后张预应力混凝土结构灌浆空洞X射线无损检测的试验研究

利用国内现有的钢结构X射线探伤设备,对后张预应力混凝土结构中灌浆空洞和预应力筋束的断丝进行无损检测的试验研究。基于混凝土内空洞的X射线透照原理,提出了波纹管内灌浆空洞的透照方法及技术指标,包括管电压、曝光时间、焦距和灵敏度等。不同强度和不同厚度混凝土试块的透照试验表明:在相同的照片黑度范围内,透照同标号混凝土的管电压和曝光时间随着混凝土厚度的增加而明显增加;在相同的透照参数下,同厚度不同标号混凝土的照片黑度差异较小;混凝土-钢材的厚度等效系数可近似取为0.2。最后,在对大量底片分析研究的基础上,给出了判别金属波纹管和PVC波纹管(包括圆形和扁形两种形式)内灌浆空洞及预应力筋束断丝的方法和步骤。

新型钢—混凝土组合的理论分析

在确定钢材和混凝土的应力—应变关系的基础上 ,应用数值方法计算了肋筋板钢—混凝土组合板的荷载—变形关系全过程曲线 ,理论计算结果与试验结果进行了比较 ,两者吻合较好。同时 ,对曲线的特点及影响参数进行了分析 ,结果表明主要影响参数是板厚 ,其次是钢材强度。

Fracture suppression at steel/concrete connection zones by ECC

In order to avoid brittle fracture failure, a ductile engineered cementitious composite （ECC） was attempted in steel/concrete connection zones to replace normal concrete. The influence of the ECC material ductility on connection failure modes and structural performance was investigated via the pushout test of stud/ECC connection, the pullout test of two-dimensional anchor bolt/ECC connection and the finite element modeling （FEM）. The experimental results suggest that the micromechanically designed ECC with a tensile ductility 300 times that of normal concrete switches the brittle fracture failure mode to a ductile one in steel connection zones. This modification in material behavior leads to higher load carrying capacity and structural ductility, which is also confirmed in FEM investigation. The enhancement in structural response through material ductility engineering is expected to be applicable to a wide range of engineering structures where steel and concrete come into contact.

预应力技术在路桥施工中的应用

目前,预应力技术在路桥工程领域引起了行业的广泛关注。采用这一先进技术,既能改善路桥工程的整体施工质量,大幅度增强路桥的使用寿命,又兼具美观性,因此具有良好的发展前景。本文中,笔者结合自身工作经验,对预应力技术做了简单论述,重点探讨了其在路桥施工中的应用情况,并强调了预应力技术在应用过程中的有关注意事项。

Flexural behaviors of steel reinforced ECC/concrete composite beams

An engineered cementitious composite （ECC） is introduced to partially substitute concrete in the tension zone of a reinforced concrete beam to form an ECC/reinforced concrete （RC） composite beam, which can increase the ductility and crack resisting ability of the beam. Based on the assumption of the plane remaining plane and the simplified constitutive models of materials, the stress and strain distributions along the depth of the composite beam in different loading stages are comprehensively investigated to obtain calculation methods of the load-carrying capacities for different stages. Also, a simplified formula for the ultimate load carrying capacity is proposed according to the Chinese code for the design of concrete structures. The relationship between the moment and curvature for the composite beam is also proposed together with a simplified calculation method for ductility of the ECC/RC composite beam. Finally, the calculation method is demonstrated with the test results of a composite beam. Comparison results show that the calculation results have good consistency with the test results, proving that the proposed calculation methods are reliable with a certain theoretical significance and reference value.

The Effect of Steel Corrosion on Bond Strength in Concrete Structures

The effect of steel corrosion on the behavior of bond between steel and the surrounding concrete was investigated. Pullout tests were carried out to demonstrate bond stress-slip response for reinforcing steel bars of a series of corrosion level. Specimens either confined or unconfined were investigated for evaluation of the effect of confinement on bond strength and failure mode. Also, the tests were analyzed using nonlinear finite element analysis. It was shown that for both confined and unconfined steel bars, bond strength generally decreases as the corrosion level increases when corrosion level is relatively high. Confinement was demonstrated to provide excellent means to conteract bond loss for corroded reinforcing steel bars. It was shown that unconfined specimens generally split at a small slip with a large crack width and result in splitting failure while confined specimens contribute to a small crack width and generally cause a pullout failure. The analysis results agree reasonably well with the experiments.

Statistical Algorithm for Damage Detection of Concrete Beams Based on Piezoelectric Smart Aggregate

The functional piezoelectric ceramic smart aggregate(SA) sensors and actuators,based on piezoelectric ceramic materials such as lead zirconium titanate(PZT),were embedded into the reinforced concrete beams with three-point bending under static loading for purposes of damage detection.The SA actuators generated the desired sine sweep excitation signals online and the SA sensors received and detected real-time signals before and after damage.The wavelet analysis and statistical characteristics about damage signals were used as a signal processing and analysis tool to extract the optimal damage information and establish a statistical damage detection algorithm.The damage index-based wavelet analysis and damage probability-based probability and statistics were proposed by PZT wavebased theory and active health monitoring technology.The results showed that the existence of cracks inside largely attenuated the amplitude of active monitoring signal after the damage of beam and the attenuation was related to the severity degree of damage.The innovative statistical algorithm of damage pattern detection based PZT-SA can effectively determine damage probability and damage degree,and provide a prediction for the critical damage location of reinforced concrete structures.The developed method can be utilized for the structural health comprehensive monitoring and damage detection on line of various large-scale concrete structures.

Electrochemical study on semiconductive properties of the passive film on rebar in concrete

The electrochemical behavior of metallic passive film on rebar in concrete is characterized by its semiconductive nature. The charge distribution at the interface between a semiconductor and an electrolyte is often determined by measuring the capacitance of the space-charge layer （Csc） as a function of the electrode potential （E）. When the space charge-layer serves as the depletion layer, the relation of Csc^-2 vs E resembles a Mott-Schottky plot （M-S plot）. The semiconductive properties of the passive film on rebar in concrete were analyzed with M-S plots to study the effect of chloride ions and mineral admixtures on rebar passive films. Some rebar electrodes were immersed in simulated concrete pore solutions, while others were embedded in concrete with/without mineral admixtures. In saturated Ca（OH）, solutions, the relation of Csc^-2-E of rebar electrodes shows linear MottSchottky relationship indicating that the passive film on rebar is a highly disordered n-type semiconductor, with donor density （ND） in the order of 10^26m^-3. After adding chloride ions （Cl wt%〈0.2%） in system solutions, the M-S plot slopes significantly decreased and ND increased, suggesting that chloride ion will cause passive film corrosion and breakdown. The M-S plots of the passive film on rebar electrodes embedded in concrete were similar to those immersed in simulated system solution. However, ND of those in concrete with mineral admixtures tended to be a little smaller, indicating that introducing proper quantity admixtures into concrete could make the rebar passive film have a thicker space-charge layer and therefore a thicker passive film layer.

Experimental study on slender reinforced concrete columns wrapped with CFRP

By axial compression tests on 6 reinforced concrete slender columns wrapped with carbon fiber-reinforced plastic (CFRP),with slenderness ratio(SR) from 4.5 to 17.5,the results show that when SR increases the retrofitting effect declines. In the case of same SR,the stability coefficient (SC) for the reinforced concrete(RC) columns with CFRP is much less than that without CFRP. There is 20% increase of stable bearing capacity to the former as compared with the latter when the SR in less than 17.5. The study summarized the simplified formula for SC,which provides a reference for engineering designers.

Fatigue properties of special kind of reinforced concrete composite beams

The special reinforced concrete composite beam consists of a steel fiber reinforced self-stressing concrete composite layer and a reinforced concrete T-beam, and constructional bars are set up at their bonding interface. Fatigue properties of the composite beam under the action of negative moment were experimentally studied. Through inverted loading mode the load-beating state of a composite beam was simulated under the action of negative moment. With the ratios of constructional bars being 0, 0.082% and 0.164% respectively as parameters, the effects of constructional bars on the properties of composite beam, such as fatigue life, crack propagation, rigidity loss as well as damage behavior of bonding interface, were studied. The mechanism of the constructional bars on the fatigue properties of the composite beams and the restriction mechanism of crack widths and rigidity loss were analyzed. The test results show that the constructional bars can enhance the shear resistance of the bonding interface between composite layer and old concrete beam and restrict expanding of steel fiber reinforced self-stressing concrete, which are beneficial to synergistic action of composite layer and old concrete beam, to reducing the stress amplitude of bars and the crack width of composite layer, and to increasing the durability and fatigue life of the composite beam.

Behaviour of GFRP R.C. Slabs in Flexure in Localenvironment An Experimental Study

A variety of new materials in the field of concrete technology have been developed during the past three decades with the ongoing demand of construction industry to meet the functional, strength, economical and durability requirements. Though reinforced concrete has high strength and is most widely used construction material it suffers from disadvantages like corrosion of steel, susceptibility to chemical and environmental attack. In order to overcome the above deficiencies of reinforced concrete new materials （special concrete composites） have been developed over the past three decades. Glass Fibre Reinforced Polymer （GFRP） is one such material with wide range of applications. Based on the preliminary investigations on GFRP bars, an optimum fiber/resin ratio of 7：3 was arrived. The tensile strength of GFRP bars is comparable to that of the mild steel as per the tests carried out, but the modulus of elasticity is about 25-30 percentage of that of steel bars. This paper deals with the experimental investigations carried out on small slab panels supported on all four edges with effective spans of 0.9 m ~ 0.45 m, which is a part of large research problem undertaken with different ratios of 10ng span to short span with different support conditions. The test results are compared with similar slab panels reinforced with conventional mild steel bars.

Double linear strain distribution assumption of RC beam strengthened with external-bonded or near-surface mounted fiber reinforced plastic

Rehabilitation of existing structures with fiber reinforced plastic(FRP)has been growing in popularity because they offer superior performance in terms of resistance to corrosion and high specific stiffness.The strain coordination results of 34 reinforced concrete beams(four groups)strengthened with different methods were presented including external-bonded or near-surface mounted glass or carbon FRP or helical rib bar in order to study the strain coordination of the strengthening materials and steel rebar of RC beam.Because there is relative slipping between concrete and strengthening materials(SM),the strain of SM and steel rebar of RC beam satisfies the double linear strain distribution assumption,that is,the strain of longitudinal fiber parallel to the neutral axis of plated beam within the scope of effective height(h0)of the cross section is in direct proportion to the distance from the fiber to the neutral axis.The strain of SM and steel rebar satisfies the equation εGCH=βεsteel,where the value of β is equal to 1.1-1.3 according to the test results.

Experimental and Computational Investigation of Hybrid FRP Bonded-Reinforced Concrete Beams under Cyclic Loading

Although several experimental and numerical studies have been carried out on the shear capacity of RC beams retrofitted by carbon or glass fibre-reinforced polymers, there has been little work on hybrid FRP sheet applications, particularly under cyclic loading. In the present research, five RC beams were constructed, and four of which were retrofitted using various schemes of FRP sheets. All beams were subjected to quasi-static cyclic loading in an attempt to represent the effect repetitive loading. The ultimate load, and deflection response at mid-span of the beams were measured and compared with predictions of a computational model based on finite element analysis. Experimental results demonstrated that hybrid applications of FRP sheets can improve the shear performance of retrofitted RC beams and increase the ultimate strain of the FRP sheets at failure. The results of the computational model were in reasonable agreement with the corresponding experimental results.

Flexural response of reinforced concrete beams strengthened with post-poured ultra high toughness cementitious composites layer

Four-point bending tests were conducted up to failure on eleven reinforced concrete (RC) beams and strengthening beams to study the effectiveness of externally pouring ultra high toughness cementitious composites (UHTCC) on improving the flexural behavior of existing RC beams.The strengthening materials included UHTCC and high strength grade concrete.The parameters,such as thickness and length of strengthening layer and reinforcement in post-poured layer,were analyzed.The flexural behavior,failure mode and crack propagation of composite beams were investigated.The test results show that the strengthening layer improves the cracking and ultimate load by increasing the cross section area.Introducing UHTCC material into strengthening not only improves the bearing capacity of the original specimens,but also disperses larger cracks in upper concrete into multiple tightly-spaced fine cracks,thus prolonging the appearance of harm surface cracks and increasing the durability of existing structures.Compared with post-poured concrete,UHTCC is more suitable for working together with reinforcement.The load?deflection plots obtained from three-dimensional finite-element model (FEM) analyses are compared with those obtained from the experimental results,and show close correlation.

Behavior and Flexural Prediction of Special Cementitious Bonding Material for Fiber Reinforced Strengthening Systems

Strengthening of RC structures with externally bonded FRP （fiber reinforced polymers） has become an important challenge in civil engineering. Epoxy is the main bonding agent used so far, but in the case of a fire, it is subjected to complete loss of his bonding capabilities. Mineral based composites strengthening systems consist of FRPs and a cementitious bonding agent which form a repair or strengthening system that is more compatible with the concrete substrata, and roved its efficiency. The current research introduces the use of a special cementitious material ＂Grancrete＂ as a bonding agent. Test results of 32 T-section RC beams strengthened with various FRG （fiber reinforced Grancrete） strengthening systems are presented. The results demonstrated that most of the specimens were likely to fail by debonding of the FRP from the concrete either at the ends or at intermediate flexural cracks. This paper presents an in-depth study aimed at the development of a better understanding of debonding failures in RC beams strengthened with externally bonded FRP systems. Different analytical models, published in the literature for plate end debonding, are reviewed and compared to test results. The results also demonstrated that when using U-wraps, the specimens were likely to fail by FRP sheet rupture.

Artificial Stone in France （1830-1930）： A Materialbetween Modernity and Tradition

1920s and 1930s architecture has often been associated with the use of modern materials, such as reinforced concrete, glass and steel, mainly thanks to the role given them by the historiography of the modern, of presenting a break with former tradition and of spreading the need of architectural renewal. The study of architecture from the point of view of construction techniques evidences, instead, how architectural renewal started earlier, during the 19 century and involved the whole realm of building, even tradition-associated materials, such as wood and stone. Indeed, artificial stone （which appeared in early 19 century） represents--above all in France--a link between traditional construction in stone and the newborn reinforced-concrete technique, so as to underline the gradual shift from 19 century construction codes to the new industrial construction techniques, which in the 1920s and 1930s tend to overlap and blend, in this way determining a material continuity of modern and 19 century architecture.

Infilled Reinforced Concrete Beams for Sustainable Construction

This paper presents a study carried out on infilled reinforced concrete beams for sustainable construction. In reinforced concrete beams, less stressed concrete below neutral axis can be replaced by some light weight material to reduce the weight of the structure and also achieve the economy. The used infilled material is brick. Sustainability can be achieved by replacing the partially used concrete. By saving concrete, the authors save cement, which reduces the green house gases emissions. So it is considered as environment friendly. Since infilled beam acts like a layered member, there needs a theory to analyze it. Method of initial functions is used for the analysis of the infilled RC （reinforced concrete） beams. This method is successfully applied on infilled beam. Results show that physical conditions are verified for infilled beam.

Renovation of the Centennial Hall

The Centennial Hall was designed as a monumental building entirely of reinforced concrete. Soon it became a model for modernist buildings of that era. During the years 2009-2011, the biggest renovation since its completion took place. All activities described in the following paper aimed to put the Centennial Hall into good repair and adjust it to the applicable requirements of modem public buildings. The primary aim is to preserve the authenticity of the original materials used in construction through the use of remedial technologies, thereby maintaining the historical integrity of the building.

Strengthening of Pultruded Glass FRP Section Combined with Concrete Slab Using CFRP Plates

This paper demonstrates the possibility of combining both glass and carbon FRP （Fibre Reinforced Polymer） composite materials with a low-cost construction material （i.e. concrete） in a hybrid system that brings higher performance levels to the design of lightweight, corrosion resistant, yet inexpensive beams providing acceptable structural properties. The objective of the research is to investigate the behaviour of a hybrid composite section under flexure. The hybrid section consists of a top concrete slab, Glass Fibre Reinforced Polymer （GFRP） beam section and Carbon Fibre Reinforced Polymer （CFRP） laminate on the extreme underside. This maximizes the benefits of each material, that is： high tensile strength of CFRP, compressive strength and low cost of concrete, light weight and lower cost of GFRP, and high corrosion resistance of all components. Three beam samples were manufactured and tested to failure while monitoring deflections and strains. By adding CFRP layers under the concrete-GFRP composite beam increases the bending strength and reduces the deflection. The most important factor in the proposed strengthening technique of GFRP-concrete composite beams by using CFRP is the adhesive material that bonds the CFRP to the GFRP. Any weakness in CFRP-GFRP bond may cause brittle failure of the beam. The study results indicate the benefits of using hybrid FRP-concrete beams to increase flexural load carrying capacity and beam stiffness and provide a numerical model that can be further developed to model more advanced material arrangements in the future. The outcome of this research provides information for both designers and researchers in the field of FRP composites.