冬季施工混凝土拌和物用水温度控制

钢筋混凝土冬季施工,使用按热平衡理论绘制的拌和物温度与水温的变化关系曲线,可随时根据拌和物的温度查出用水温度,给施工带来方便。

Strengthening effects of BFRP on reinforced concrete beams

Reinforced concrete （RC） beams externally bonded with basalt fiber reinforced polymer （BFRP） are experimentally investigated by using different numbers of bonding plies, transverse anchorages as well as the initial conditions of strengthened beams. The performances of the BFRP strengthening are compared with those of the carbon fiber reinforced polymer （CFRP） and the glass fiber reinforced polymer （GFRP） under the same experimental condition. Experimental results indicate that the strength and ductility of the strengthened beam with two plies of the BFRP are improved remarkably than those with one ply. The strengthening effects of the BFRP lie between those of the CFRP and the GFRP. The BFRP strengthening is little influenced by pre-cracks of concrete. Most failures are caused by interfaciai debonding induced by flexural cracks in the experiment. Clamping of Uwraps along the whole beam is less efficient than endpoint anchorage for increasing the ultimate load of the strengthened beam. Finally, the models suggested by the five guidelines for predicting the debonding strain of the CFRP are extended to the BFRP and the conservative estimates of the debonding strain of the BFRP are given as well.

Durability of concrete beams reinforced with CFRP sheet under wet-dry cycles and loading

The test results of eight concrete beams reinforced with carbon fiber reinforced polymer （CFRP） sheets subjected to an aggressive environment under a sustained load are presented. The beams are 1 700 mm long with a rectangular cross-section of 120- mm width and 200-mm depth. The beams are precracked with a four-point flexural load, bonded CFRP sheets, and placed into wet-dry saline water（ NaCl） either in an unstressed state or loaded to about 30% or 60% of the initial ultimate load. The individual and coupled effects of wet-dry saline water and sustained bending stresses on the long term behaviour of concrete beams reinforced with the CFRP are investigated. The test results show that the coupled action of wet-dry saline water and sustained bending stresses appears to significantly affect the load capacity and the failure mode of beam strengthened with CFRP, mainly due to the degradation of the bond between CFRP and concrete. However, the stiffness is not affected by the coupled action of wet-dry cycles and a sustained load.

Static cyclic-loading test on new type of rigid connection of steel girder and reinforced concrete pier

A new type of rigid connection of steel girder and reinforced concrete pier of a bridge is proposed. The components in rigid connection are installed by high strength bolts on the spot, which are very convenient in construction. The moment from superstructure can be effectively transferred to substructure, and the plates provided for shear transferring can withstand the majority of total horizontal force. With static cyclic loading test, useful experimental data is obtained on the new type of connection of steel superstructure and concrete substructure. As a result, the stress transfer mechanism of the rigid connection can be made clearly and the seismic performance of this structure can also be clarified. Compared computed strength and ductility with actual results, it can be found that this type of connection has good energy absorption capacity in spite of large displacement and no local buckling arises at the locations where stress concentration occurs. Because of doing away with the expensive bearing, this new type of composite structure can be expected to construct a bridge with high seismic resistant capacity thus saving in total construction cost.

Fatigue behavior of crane beam strengthened with CFRP

In order to study the fatigue behavior of the damaged reinforced concrete （RC） beams strengthened by carbon fiber reinforced polymer （CFRP） laminate, three T-shaped beams strengthened by CFRP and one contrasting beam are tested under fatigue loading, with the parameters of different modes of strengthening and different fatigue load levels considered. The main results obtained from the tests are： the width of the crack decreases 50. 2% to 66%, and the development of the crack is limited; the stress of steel decreases 24. 1% to 28. 2%, and the stiffness increases 14.9% to 16. 1% after being strengthened. Based on the technical specification for strengthening concrete structures with CFRP and the conclusions from the tests, a calculating scheme of the flexure stiffness is given, which can be used for reference in engineering design. Finally, some suggestions are given for design in fatigue strengthening.

Behavior of interfacial stresses between RC beams and GFRP sheets

Seven reinforced concrete （RC） beams with epoxy-bonded glass fiber reinforced plastic （GFRP） sheets and two control RC beams were experimentally tested to investigate the bond behavior of the interfaces between RC beams and GFRP sheets. The variable parameters considered in test beams are the layers of GFRP sheets, the bond lengths and the reinforcement ratios. The results indicate that the flexural strength of the repaired beams is increased, but the ultimate load of beams with GFRP sheets debonding failure is reduced relatively. The bond length is the main factor that results in bonding failure of the strengthened beams. An experimental method of interfacial shear stress is proposed to analyze the distribution of shear stress according to experimental results. The analytical method of shear and normal stresses and a simple equation are proposed to predict the peeling loads. The proposed model is applied to experimental beams. The analytical results show a good agreement with the experimental results.

Ultimate flexural strength of normal section of FRP-confined RC circular columns

Numerical analysis is carried out to study the sectional properties of the fiber-reinforced polymer（FRP）-confined reinforced concrete（RC）circular columns. The axial load ratio, the FRP confinement ratio and the longitudinal reinforcement characteristic value are the three main parameters that can influence the neutral axis depth when concrete compression strain reaches an ultimate value. The formula for computing the central angle θ, corresponding to the compression zone, is established according to the data regression of the numerical analysis results. The numerical analysis results demonstrate that the concrete stress enhancement from transverse confinement and strain hardening of the longitudinal reinforcement can cause a much greater flexural strength than that defined by the design code. Based on the analytical studies and the test results of 36 large scale columns, the formula to calculate the flexural strength when columns fail under seismic loading is proposed, and the calculated results agree well with the test results. Finally, parametric studies are conducted on a typical column with different axial load ratios, longitudinal reinforcement characteristic value and FRP confinement ratios. Analysis of the results shows that the calculated flexural strength can be increased by 50% compared to that of unconfined columns defined by the code.

Seismic strengthening of reinforced concrete columns damaged by rebar corrosion using combined CFRP and steel jacket

In order to study the effectiveness of combined carbon fiber-reinforced polymer （CFRP） sheets and steel jacket in strengthening the seismic performance of corrosion-damaged reinforced concrete （RC） columns, twelve reinforced concrete columns are tested under combined lateral cyclic displacement excursions and constant axial load. The variables studied in this program include effects of corrosion degree of the rebars, level of axial load, the amount of CFRP sheets and steel jacket. The results indicate that the combined CFRP and steel jacket retrofitting technique is effective in improving load-carrying, ductility and energy absorption capacity of the columns. Compared with the corrosion-damaged RC column, the lateral load and the ductility factor of many strengthened columns increase more than 90% and 100%, respectively. The formulae for the calculation of the yielding load, the maximum lateral load and the displacement ductility factor of the strengthened columns under combined constant axial load and cyclically increasing lateral loading are developed. The test results are also compared with the results obtained from the proposed formulae. A good agreement between calculated values and experimental results is observed.

Flexural behaviors of FRP strengthened corroded RC beams

The flexural behavior of eight FRP （ fiber reinforced polymer） strengthened RC （reinforced concrete） beams with different steel corrosion rates are numerically studied by Ansys finite element software. The influences of the corrosion rate on crack pattern, failure mechanism, ultimate strength, ductility and deformation capacity are also analyzed. Modeling results show that the beams with low corrosion rates fail by the crushing of the concrete in the compression zone. For the beams with medium corrosion rates, the bond slip between the concrete and the longitudinal reinforcement occurs after steel yielding, and the beams finally fail by the debonding of the FRP plates. For the beams with high corrosion rates, the bond slip occurs before steel yielding, and the beams finally fail by the crushing of the concrete in the compression zone. The higher the corrosion rates of the longitudinal reinforcement, the more the carrying capacity of FRP strengthened RC beams reduces. The carrying capacity of RCB-1 （the corrosion rate is 0） is 115 kN, and the carrying capacity of RCB-7 （the corrosion rate is 20% ） is 42 kN. The deformation capacity of FRP strengthened corroded RC beams is higher than that of FRP strengthened uucorroded RC beams. The ultimate deflection of RCB-1 and RCB-7 are 20 mm and 35 nun, respectively, and the ultimate deflection of RCB-5 （the corrosion rate is 10% ） reaches 60 ilUn.

STATE-OF-ART ON CORROSION AND PREVENTION OF REINFORCED CONCRETE

The corrosion causes of rebar in concrete under corrosive environment are analyzed and discussed. It is mainly suffered from the penetration of corrosive species from environment in to the surface of rebar. Corrosion is initiated by penetration of chlorides and breakdown of passivation, and then propagated by crack of concrete induced by st ress from volume expansion of corrosion product of rebar in succession. Some eff ective countermeasures for corrosion prevention for reinforced concrete are brie fly specified and discussed. Finally, some important techniques commonly used or to be developed are also suggested.

Comparison study on calculation methods of bending behavior of Chinese reinforced concrete beams from 1912 to 1949

In order to study the calculation methods of bending behavior of Chinese reinforced concrete beams from 1912 to 1949, tests on the mechanical performance of 66 rebars from different modem Chinese concrete buildings, the concrete compressive strength of 12 modem Chinese concrete buildings, and the concrete cover thickness of 9 modem Chinese concrete buildings are carried out; and the actual material properties and structural conformations of modem Chinese concrete buildings are obtained. Then, the comparison on calculation methods of bending behavior including the original Chinese calculation method, the present Chinese calculation method, the present American calculation method and the present European calculation method is studied. The results show that the original Chinese calculation method of bending behavior is based on the allowable stress calculation method, and the design safety factors are 3.55 to 4. 0. In term of the calculation area of longitudinal rebars of reinforced concrete beams, without considering earthquake action, the original Chinese structural calculation method is safer than the present Chinese structural calculation method, the present European structural calculation method, and the present American structural calculation method. The results can provide support for the structural safety assessments of modem Chinese reinforced concrete buildings.

MODIFICATON AND RESEARCH ON BENDING RIGIDITY FORMULA OF REINFORCED CONCRETE BEAM

Beam stiffness degrades with its age in service and its service performance is weakened.According to the fundamental characteristics of the reinforced concrete,the influence of stiffness degradation caused by different kinds of damage is obtained.Among them,the crack is the most direct and obvious factor.Furthermore,according to the analysis of bending rigidity formula presented in current standard,an influence parameter of crack development on the stiffness degradation,i.e.,nonuniformity coefficient of tensile steel strain φ,is extracted.Average crack distance and crack depth are taken as crack statistic parameters.Based on analysis and modeling with ANSYS,the modified bending rigidity formula related to crack is obtained.

Nonlinear Behavior of Reinforced Concrete Slit Shear Walls under Seismic Actions *

A reinforced concrete slit shear wall is a new breed of earthquake resistant structure recently proposed by the authors. In this paper, the seismic responses of the slit shear walls under the shake of earthquake excitation have been dealt with. Based on a simplified structural model, which is shown to have a sufficient accuracy for the real slit shear wall structure, the analysis focuses on the influence of nonlinear behavior of the connecting beams between the slits on the dynamic performance of the whole slit shear wall structure. It has been found that the yielding of connecting beams in a slit shear wall can provide significant improvement in reducing the structural responses, and by choosing an appropriate strength value for the connecting beams, it is possible to optimize the seismic response of the slit shear wall.

Probabilistic durability assessment approach of deteriorating RC bridges

A stochastic finite element computational methodology for probabilistic durability assessment of deteriorating reinforced concrete（RC） bridges by considering the time-and space-dependent variabilities is presented.First,finite element analysis with a smeared cracking approach is implemented.The time-dependent bond-slip relationship between steel and concrete,and the stress-strain relationship of corroded steel bars are considered.Secondly,a stochastic finite element-based computational framework for reliability assessment of deteriorating RC bridges is proposed.The spatial and temporal variability of several parameters affecting the reliability of RC bridges is considered.Based on the data reported by several researchers and from field investigations,the Monte Carlo simulation is used to account for the uncertainties in various parameters,including local and general corrosion in rebars,concrete cover depth,surface chloride concentration,chloride diffusion coefficient,and corrosion rate.Finally,the proposed probabilistic durability assessment approach and framework are applied to evaluate the time-dependent reliability of a girder of a RC bridge located on the Tianjin Binhai New Area in China.

Reliability analysis for anchorage of reinforced concrete beams with longitudinal cracks due to corrosion at anchorage zone

An anchorage reliability analysis approach for simply supported reinforced concrete beams under corrosion attack in the anchorage zone is developed.The first-order second-moment method is employed to analyze the effects of various factors on the anchorage reliability.These factors include both the length and width of cover cracking due to reinforcement corrosion,the cover thickness,the anchorage length,and the stirrup ratio.The results show that the effect of corrosion-induced crack length on the reliability index for anchorage,β0,is negligible when the crack on the concrete surface is just appearing,but with the crack widening,the β0 value is reduced significantly;the considerable changes in β0 result from a variation in cover depth and anchorage length;the effect of changes in the diameter or space of stirrups on the anchorage resistance is very limited,and the variation in β0 is also very low.

Experimental study and calculation of flexural capacity of RC beams strengthened with GFRP sheets

Nine reinforced concrete (RC) beams strengthened by glass fiber reinforced polymer (GFRP) sheets and three control beams are tested. Four parameters are considered in this experimental program included the concrete strength, the reinforcement ratio, the number of GFRP sheets, and the shear span ratio. It is shown that the application of GFRP sheets can increase the ultimate flexural capacity. The effect of the concrete strength, the reinforcement ratio and the number of GFRP sheets on load capacity is obvious. The shear span ratio can affect the failure mode of RC beams strengthened by GFRP sheets. A theoretical model for flexural behavior of the strengthened RC beam is also developed.

Strength of circular concrete columns under concentric compression

An experimental study, in which six columns were loaded concentrically toinvestigate the behavior of reinforced normal strength and high strength circular columns underconcentric compression, is described. The concrete strengths of the columns were 30 MPa and 60 MPa.The primary variables considered were the concrete strength and the amount of transversereinforcement. Test results indicate that smaller hoop spacing provides higher column capacity andgreater strength enhancement in a confined concrete core of columns. For the same lateralconfinement, high strength concrete columns develop lower strength enhancement than normal strengthconcrete columns. Both the strength enhancement ratio (f'_(cc) /f'_(co)) and the column capacityratio (P_(test)/P_o) were observed to show linear increase variations with rho_s f_(yt)/f'_c incircular columns.

Application of ALE Method on the Numerical Simulation of Reinforced Concrete Penetration

LS-DYNA program and the principle of ALE method were introduced, and the target features of the reinforced concrete penetration were analyzed by using the D material model and the ALE method. A numerical simulation has been done to show the penetration visually and veritably. The simulation results are analyzed carefully and explicitly prove their significance to the research of reinforced concrete penetration.

Flexural behaviors of steel reinforced ECC/concrete composite beams

An engineered cementitious composite （ECC） is introduced to partially substitute concrete in the tension zone of a reinforced concrete beam to form an ECC/reinforced concrete （RC） composite beam, which can increase the ductility and crack resisting ability of the beam. Based on the assumption of the plane remaining plane and the simplified constitutive models of materials, the stress and strain distributions along the depth of the composite beam in different loading stages are comprehensively investigated to obtain calculation methods of the load-carrying capacities for different stages. Also, a simplified formula for the ultimate load carrying capacity is proposed according to the Chinese code for the design of concrete structures. The relationship between the moment and curvature for the composite beam is also proposed together with a simplified calculation method for ductility of the ECC/RC composite beam. Finally, the calculation method is demonstrated with the test results of a composite beam. Comparison results show that the calculation results have good consistency with the test results, proving that the proposed calculation methods are reliable with a certain theoretical significance and reference value.

Bond strength improvement of GFRP rebars with different rib geometries

Based on the Canadian Standards Association (CSA) criteria,105 pullout specimens were tested to investigate the effect of different rib geometries on bond strength of glass fiber reinforced polymer (GFRP) rebars embedded in concrete. Two kinds of conventional reinforcing rebars were also studied for comparison. Each rebar was embedded in a 150 mm concrete cube,with the embedded length being four times the rebar diameter. The experimental parameters were the rebar type,rebar component,rebar diameter,rebar surface texture,rib height,rib spacing and rib width. Theoretical analysis was also carried out to explain the experimental phenomena and results. The experimental and theoretical results indicated that the bond strength of GFRP rebars was about 13%～35% lower than that of steel rebars. The bond strength and bond-slip behavior of the specially machined rebars varied with the rebar type,rebar diameter,rebar surface texture,rib height,rib spacing and rib width. Using the results,design recom-mendations were made concerning optimum rib geometries of GFRP ribbed rebars with superior bond-slip characteristics,which concluded that the optimal rib spacing of ribbed rebars is the same as the rebar diameter,and that the optimal rib height is 6% of the rebar diameter.