采用离散单元法DEM（discrete element method）对圆柱形生物质颗粒和钢球颗粒在滚筒中的混合进行了数值模拟,分析了滚筒转速和颗粒数量比对混合质量的影响。结果表明：在本文设定的工况下,颗粒的混合模式为阶梯模式,并且颗粒在混合时...采用离散单元法DEM（discrete element method）对圆柱形生物质颗粒和钢球颗粒在滚筒中的混合进行了数值模拟,分析了滚筒转速和颗粒数量比对混合质量的影响。结果表明：在本文设定的工况下,颗粒的混合模式为阶梯模式,并且颗粒在混合时可以分成3个区域,即左面的单层钢球颗粒区、中间的钢球颗粒和生物质颗粒混合区、右面的生物质颗粒堆积区。左右两边的颗粒混合效果较差,中间的颗粒混合效果较好。当滚筒转速相同时,钢球颗粒和生物质颗粒数量比为3000∶200时的颗粒混合效果比钢球颗粒和生物质颗粒数量比为3000∶100时的好,即当钢球颗粒数量远大于生物质颗粒数量时,增加生物质颗粒的数量可以提高混合效果。在钢球颗粒和生物质颗粒数量比相同的情况下,当滚筒转速在5-25r/min的范围内,滚筒转速越高,颗粒的混合质量越好,并且颗粒混合达到稳定的时间就越短。展开更多
TiN/TiAlN multilayer coatings were prepared by arc ion plating with separate targets. In order to decrease the unfavorable macroparticles, a straight magnetized filter was used for the low melting aluminium target. Th...TiN/TiAlN multilayer coatings were prepared by arc ion plating with separate targets. In order to decrease the unfavorable macroparticles, a straight magnetized filter was used for the low melting aluminium target. The results show that the output plasmas of titanium target without filter and aluminium target with filter reach the substrate with the same order of magnitude. Meanwhile, the number of macropartieles in TiN/TiAlN multilayer coatings deposited with separate targets is only 1/10-1/3 of that deposited with alloy target reported in literature. Al atom addition may lead to the decrease of peak at （200） lattice plane and strengthening of peak at （111） and （220） lattice planes. The measured hardness of TiN/TiAlN multilayer coatings accords with the mixture principle and the maximum hardness is HV2495. The adhesion strength reaches 75 N.展开更多
通过调整WC颗粒尺寸(50μm和100μm)和质量分数(25%、35%和45%),采用新型的复合电冶熔铸工艺制备了4种WC颗粒增强钢基复合材料,以及作为对比的5Cr Ni Mo钢,对经过不同热处理的复合材料进行干滑动摩擦磨损试验,研究了各试样的摩擦因数和...通过调整WC颗粒尺寸(50μm和100μm)和质量分数(25%、35%和45%),采用新型的复合电冶熔铸工艺制备了4种WC颗粒增强钢基复合材料,以及作为对比的5Cr Ni Mo钢,对经过不同热处理的复合材料进行干滑动摩擦磨损试验,研究了各试样的摩擦因数和磨损量,并对磨损形貌进行分析。结果表明:随着WC含量或颗粒度在一定范围内增大,摩擦因数呈提高的趋势。在1000℃淬火+180℃回火,粗颗粒的WC含量为45%时,复合材料表现出最佳的耐磨性,是5Cr Ni Mo钢的21.96倍,是粗颗粒含量25%和35%时的10.65倍和8.91倍,是细颗粒含量45%时的5.35倍。PRMMC在干滑动摩擦磨损条件下的磨损机制为磨粒磨损和氧化磨损。展开更多
Impact wear behaviors of Hadfield manganese steel at different impact angles were investigated. The results of impact wear tests show that there exists a critical impact load for Hadfield steel. The wear rate suddenly...Impact wear behaviors of Hadfield manganese steel at different impact angles were investigated. The results of impact wear tests show that there exists a critical impact load for Hadfield steel. The wear rate suddenly turns down after some impact cycles when the impact load is greater than the critical load. The critical impact load is smaller than 8.2 J in this research because the nano-sized austenitic grains embedded in amorphous delay the crack propagation in subsurface. From high resolution transmission electron microscope (HRTEM) examination of subsurface microstructure, it is found that a large amount of nano-sized grains embedded in bulk amorphous matrix are fully developed and no martensitic transformation occurs during the impact wear process. The analytical results of worn surface morphology and debris indicate that the initiation of crack, propagation and spalling are restricted in the amorphous phase, resulting in the size distribution of debris in nano-sizes, which is the reason why the wear rate of Hadfield steel is greatly decreased at high impact load.展开更多
The carbon steels dispersed with ultrafine TiC particles were fabricated by conventional casting method. The casting process is more economical than other available routes for metal matrix composite production, and th...The carbon steels dispersed with ultrafine TiC particles were fabricated by conventional casting method. The casting process is more economical than other available routes for metal matrix composite production, and the large sized components to be fabricated in short processing time. However, it is extremely difficult to obtain uniform dispersion of ultrafine ceramic particles in liquid metals due to the poor wettability and the specific gravity difference between the ceramic particle and metal matrix. In order to solve these problems, the mechanical milling (MM) and surface-active processes were introduced. As a result, Cu coated ultrafine TiC powders made by MM process using high energy ball milling machine were mixed with Sn powders as a surfactant to get better wettability by lowering the surface tension of carbon steel melt. The microstructural investigations by OM show that ultrafine TiC particles are distributed uniformly in carbon steel matrix. The grain sizes of the cast matrix with ultrafine TiC particles are much smaller than those without ultrafine TiC particles. This is probably due to the fact that TiC particles act as nucleation sites during solidification. The wear resistance of cast carbon steel composites added with MMed TiC/Cu-Sn powders is improved due to grain size refinement.展开更多
文摘采用离散单元法DEM（discrete element method）对圆柱形生物质颗粒和钢球颗粒在滚筒中的混合进行了数值模拟,分析了滚筒转速和颗粒数量比对混合质量的影响。结果表明：在本文设定的工况下,颗粒的混合模式为阶梯模式,并且颗粒在混合时可以分成3个区域,即左面的单层钢球颗粒区、中间的钢球颗粒和生物质颗粒混合区、右面的生物质颗粒堆积区。左右两边的颗粒混合效果较差,中间的颗粒混合效果较好。当滚筒转速相同时,钢球颗粒和生物质颗粒数量比为3000∶200时的颗粒混合效果比钢球颗粒和生物质颗粒数量比为3000∶100时的好,即当钢球颗粒数量远大于生物质颗粒数量时,增加生物质颗粒的数量可以提高混合效果。在钢球颗粒和生物质颗粒数量比相同的情况下,当滚筒转速在5-25r/min的范围内,滚筒转速越高,颗粒的混合质量越好,并且颗粒混合达到稳定的时间就越短。
基金Projects (50773015, 10775036) supported by the National Natural Science Foundation of China
文摘TiN/TiAlN multilayer coatings were prepared by arc ion plating with separate targets. In order to decrease the unfavorable macroparticles, a straight magnetized filter was used for the low melting aluminium target. The results show that the output plasmas of titanium target without filter and aluminium target with filter reach the substrate with the same order of magnitude. Meanwhile, the number of macropartieles in TiN/TiAlN multilayer coatings deposited with separate targets is only 1/10-1/3 of that deposited with alloy target reported in literature. Al atom addition may lead to the decrease of peak at （200） lattice plane and strengthening of peak at （111） and （220） lattice planes. The measured hardness of TiN/TiAlN multilayer coatings accords with the mixture principle and the maximum hardness is HV2495. The adhesion strength reaches 75 N.
文摘通过调整WC颗粒尺寸(50μm和100μm)和质量分数(25%、35%和45%),采用新型的复合电冶熔铸工艺制备了4种WC颗粒增强钢基复合材料,以及作为对比的5Cr Ni Mo钢,对经过不同热处理的复合材料进行干滑动摩擦磨损试验,研究了各试样的摩擦因数和磨损量,并对磨损形貌进行分析。结果表明:随着WC含量或颗粒度在一定范围内增大,摩擦因数呈提高的趋势。在1000℃淬火+180℃回火,粗颗粒的WC含量为45%时,复合材料表现出最佳的耐磨性,是5Cr Ni Mo钢的21.96倍,是粗颗粒含量25%和35%时的10.65倍和8.91倍,是细颗粒含量45%时的5.35倍。PRMMC在干滑动摩擦磨损条件下的磨损机制为磨粒磨损和氧化磨损。
基金Project(59771048) supported by the National Natural Science Foundation of China project(2002AA302509) supportedby the High Technology Research and Development Program of China
文摘Impact wear behaviors of Hadfield manganese steel at different impact angles were investigated. The results of impact wear tests show that there exists a critical impact load for Hadfield steel. The wear rate suddenly turns down after some impact cycles when the impact load is greater than the critical load. The critical impact load is smaller than 8.2 J in this research because the nano-sized austenitic grains embedded in amorphous delay the crack propagation in subsurface. From high resolution transmission electron microscope (HRTEM) examination of subsurface microstructure, it is found that a large amount of nano-sized grains embedded in bulk amorphous matrix are fully developed and no martensitic transformation occurs during the impact wear process. The analytical results of worn surface morphology and debris indicate that the initiation of crack, propagation and spalling are restricted in the amorphous phase, resulting in the size distribution of debris in nano-sizes, which is the reason why the wear rate of Hadfield steel is greatly decreased at high impact load.
基金supported by the Korea Atomic Energy Research Institute (KAERI) R&D Program
文摘The carbon steels dispersed with ultrafine TiC particles were fabricated by conventional casting method. The casting process is more economical than other available routes for metal matrix composite production, and the large sized components to be fabricated in short processing time. However, it is extremely difficult to obtain uniform dispersion of ultrafine ceramic particles in liquid metals due to the poor wettability and the specific gravity difference between the ceramic particle and metal matrix. In order to solve these problems, the mechanical milling (MM) and surface-active processes were introduced. As a result, Cu coated ultrafine TiC powders made by MM process using high energy ball milling machine were mixed with Sn powders as a surfactant to get better wettability by lowering the surface tension of carbon steel melt. The microstructural investigations by OM show that ultrafine TiC particles are distributed uniformly in carbon steel matrix. The grain sizes of the cast matrix with ultrafine TiC particles are much smaller than those without ultrafine TiC particles. This is probably due to the fact that TiC particles act as nucleation sites during solidification. The wear resistance of cast carbon steel composites added with MMed TiC/Cu-Sn powders is improved due to grain size refinement.
