2400kW工频感应铜熔化炉的主回路分析

某铜业公司由 Ajax 公司引进的2400kW 铜熔化炉是目前国内最大的工频感应铜熔化炉,采用两只感应器、T 型接线及晶闸管无级调压调功。本文对这台熔化炉的主回路进行了详细分析,指出了其几个值得借鉴的设计特点,并结合国内外工频感应炉的现状,探讨了未来工频感应炉的发展方向。

有芯工频熔铜炉筑炉启炉工艺

正确的筑炉方法是保证有芯工频感应熔铜炉开炉成功的基本前提。选用合理的捣打料,进行正确的粒度配合,并添加一定比例的红柱石、碳化硅是提高熔铜炉的烧结强度的有效措施。采用分层递降厚度的加料方式,打结层表面拉毛并取出细粉,有利于料层之间的粘接。采用中心环形辐射式向外逐圈打结的方法,二级密实的捣打工艺,并进行三段式烘炉启炉,有利于启炉成功和延长炉龄。

Thermodynamic analysis and process optimization of zinc and lead recovery from copper smelting slag with chlorination roasting

An efficient chlorination roasting process for recovering zinc(Zn)and lead(Pb)from copper smelting slag was proposed.Thermodynamic models were established,illustrating that Zn and Pb in copper smelting slag can be efficiently recycled during the chlorination roasting process.By decreasing the partial pressure of the gaseous products,chlorination was promoted.The Box−Behnken design was applied to assessing the interactive effects of the process variables and optimizing the chlorination roasting process.CaCl_(2) dosage and roasting temperature and time were used as variables,and metal recovery efficiencies were used as responses.When the roasting temperature was 1172℃ with a CaCl_(2) addition amount of 30 wt.%and a roasting time of 100 min,the predicted optimal recovery efficiencies of Zn and Pb were 87.85%and 99.26%,respectively,and the results were validated by experiments under the same conditions.The residual Zn-and Pb-containing phases in the roasting slags were ZnFe_(2)O_(4),Zn_(2)SiO_(4),and PbS.

Iron and copper recovery from copper slags through smelting with waste cathode carbon from aluminium electrolysis

To recover metal from copper slags,a new process involving two steps of oxidative desulfurization followed by smelting reduction was proposed in which one hazardous waste(waste cathode carbon)was used to treat another(copper slags).The waste cathode carbon is used not only as a reducing agent but also as a fluxing agent to decrease slag melting point.Upon holding for 60 min in air atmosphere first and then smelting with 14.4 wt%waste cathode carbon and 25 wt%CaO for 180 min in high purity Ar atmosphere at 1450℃,the recovery rates of Cu and Fe reach 95.89%and 94.64%,respectively,and meanwhile greater than 90%of the fluoride from waste cathode carbon is transferred into the final slag as CaF_(2) and Ca_(2)Si_(2)F_(2)O_(7),which makes the content of soluble F in the slag meet the national emission standard.Besides,the sulphur content in the obtained Fe-Cu alloy is low to 0.03 wt%.

电厂发电机转子开裂失效分析

某电厂发电机大轴正极发生短路事故,转子内部产生裂纹。通过宏观检查、微观组织分析、扫描电镜分析、能谱分析及化学成分分析等对发电机转子内部开裂情况进行了失效分析。结果表明,转子大轴主要失效模式为液态金属脆断。对脆化裂纹的失效特征及产生机理进行了分析,并对发电机大轴的安全使用提供了处理方案和合理化建议。

Electrolytic production of Cu-Ni alloys in CaCl_2-Cu_2S-NiS molten salt

An alternative metal/alloy production method,known as direct electrochemical reduction(DER),was introduced for the fabrication of CuNi alloys from mixed sulfides(Cu2S,NiS)under both galvanostatic and potentiostatic conditions.The influences of the process parameters(e.g.,cell voltage and current)on the compositions of the reduced compounds were investigated to yield industrially desirable alloys,namely,CuNi10,CuNi20,and CuNi30.The electrochemical behaviors of Cu2S and NiS in CaCl2 melt were examined at a temperature of 1200°C via cyclic voltammetry(CV).Based on the CV results,the cathodic reduction of Cu2S occurred in one step and cathodic reductions of NiS occurred in two steps,i.e.,Cu2S?Cu for copper reduction and NiS?Ni3S2?Ni for nickel reduction.Galvanostatic studies revealed that it was possible to fabricate high-purity CuNi10 alloys containing a maximum sulfur content of 320×10-6 via electrolysis at 10 A for 15 min.Scanning electron microscopy along with energy-dispersive X-ray spectrometry and optical emission spectroscopy(OES)examinations showed that it was possible to fabricate CuNi alloys of preferred compositions and with low levels of impurities,i.e.,less than 60×10-6 sulfur,via DER at 2.5 V for 15 min.

Development of non-premixed porous inserted regenerative thermal oxidizer

In this study, a porous inserted regenerative thermal oxidizer （PRTO） system was developed for a 125 kW industrial copper-melting furnace, due to its advantages of low NOr emissions and high radiant efficiency. Zirconium dioxide （ZrOz） ce- ramic foams were placed into the combustion zone of a regenerative thermal oxidizer （RTO）. Different performance characteris- tics of the RTO and PRTO systems, including pressure drop, temperature distribution, emissions, and energy efficiency, were evaluated to study the effects of the porous inserts on non-premixed CH4 combustion. It was found that the PRTO system achieved a significant reduction in the NOx emission level and a fuel saving of approximately 30% compared to the RTO system. It is most suitable for a lean combustion process at an equivalence ratio 〈0.4 with NOx and CO emission levels within 0.002%~）.003% and 0.001%q3.002%, respectively.

Dendritic growth and solute trapping in rapidly solidified Cu-based alloys

Rapid solidification of binary Cu-22%Sn peritectic alloys and Cu-5%Sn-5%Ni-5%Ag quaternary alloys was accomplished by glass fluxing, drop tube and melt spinning methods. The undercooled, by glass fluxing method, Cu-22%Sn peritectic alloy was composed of a（Cu） and δ（Cu41Snll） phases. If rapidly solidified in a drop tube, the alloy phase constitution changed from α（Cu） and δ（Cu41Sn11） phases into a single supersaturated （Cu） phase with the reducing of droplet diameter, and the maximum solubility of Sn in （Cu） phase extended to 22%. The Cu-5%Sn-5%Ni-5%Ag quaternary alloy was composed of （Cu） and （Ag） phases under the containerless processing condition in a drop tube, and the solute microsegregation of （Cu） phase was obvious. When the Cu-5%Sn-5%Ni-5%Ag quaternary alloy was solidified by melt spinning method, microsegregation was suppressed and solute trapping occurred. The experimental results show that the microstructures of primary （Cu） phase in the two alloys transfer from coarse dendrites into equiaxed grains with the increase of cooling rate and undercooling, which is accompanied by the grain refinement effect.