The inhomogeneity of density and mechanical properties of A357 aluminum alloy in the semi-solid state were investigated.Numerical simulation and backward extrusion were adopted to study the preparation of cup shells.T...The inhomogeneity of density and mechanical properties of A357 aluminum alloy in the semi-solid state were investigated.Numerical simulation and backward extrusion were adopted to study the preparation of cup shells.The results show that the relative density of the wall is the lowest in samples,and that of the base is the highest.With increasing the billet height,more time is needed for relative density of the corner to reach the maximum value,and the relative densities in every region improve evidently with increasing the pressure.The tensile stress was simulated to be the largest at the corner,and the hot tearings were forecasted to mainly appear at the corner too.By employing proper billet height and pressure,the extruded samples consisted of fine and uniform microstructures,and can obtain excellent mechanical properties and Brinell hardness.展开更多
The effect of dynamic recrystallization(DRX)on the microstructure and mechanical properties of 6063 aluminum alloy profile during porthole die extrusion was studied through experiment and simulation.The grain morpholo...The effect of dynamic recrystallization(DRX)on the microstructure and mechanical properties of 6063 aluminum alloy profile during porthole die extrusion was studied through experiment and simulation.The grain morphology was observed by means of electron backscatter diffraction(EBSD)technology.The results show that,at low ram speeds,increasing the ram speed caused an increase in DRX fraction due to the increase of temperature and strain rate.In contrast,at high ram speeds,further increasing ram speed had much less effect on the temperature,and the DRX faction decreased due to high stain rates.The microhardness and fraction of low angle boundaries in the welding zones were lower than those in the matrix zones.The grain size in the welding zone was smaller than that in the matrix zone due to lower DRX fraction.The decrease of grain size and increase of extrudate temperature were beneficial to the improvement of microhardness.展开更多
The 4-lobe aluminum alloy helical surface rotors are widely applied in industry,such as superchargers.Generally,the conventional manufacturing processes of aluminum alloy helical surface are time consuming and costly....The 4-lobe aluminum alloy helical surface rotors are widely applied in industry,such as superchargers.Generally,the conventional manufacturing processes of aluminum alloy helical surface are time consuming and costly.To make the manufacturing processes more flexible and economical,the forward hot extrusion process is proposed to form the 4-lobe aluminum alloy helical surface rotors.In this work,we implement both simulations and experiments to the forming process of the helical surface,of which the material is 6063 aluminum alloy.The forward hot extrusion process is simulated with finite element method in DEFORM-3D.Based on the simulation method,the influences of different extrusion parameters,such as extrusion temperature,extrusion speed and extrusion ratio,on the extrusion process are studied.According to the numerical simulation results,the optimal case is chosen to carry out the experiment.Furthermore,the experimental results show that the surface is smooth;the toothed fill is full;the twist angle in the length direction is evenly distributed;the value of twist angle is roughly in line with the design angle,which is mainly due to the modified die structure,having a positive and significant effect on the increment of twist angle.Therefore,the twist angle has an increase of about 76%,which verifies the modified die structure.展开更多
An innovative approach was introduced for the development of a AA6063 recrystallization model.This method incorporated a regression-based technique for the determination of material constants and introduced novel equa...An innovative approach was introduced for the development of a AA6063 recrystallization model.This method incorporated a regression-based technique for the determination of material constants and introduced novel equations for assessing the grain size evolution.Calibration and validation of this methodology involved a combination of experimentally acquired microstructural data from the extrusion of three different AA6063 profiles and results from the simulation using the Qform Extrusion UK finite element code.The outcomes proved the agreement between experimental findings and numerical prediction of the microstructural evolution.The trend of the grain size variation based on different process parameters was accurately simulated,both after dynamic and static recrystallization,with an error of less than 25% in almost the whole sampling computations.展开更多
基金Projects(50774026,50875059)supported by the National Natural Science Foundation of ChinaProject(20070420023)supported by the China Postdoctoral Science FoundationProject(2008AA03A239)supported by the High-tech Research and Development Program of China
文摘The inhomogeneity of density and mechanical properties of A357 aluminum alloy in the semi-solid state were investigated.Numerical simulation and backward extrusion were adopted to study the preparation of cup shells.The results show that the relative density of the wall is the lowest in samples,and that of the base is the highest.With increasing the billet height,more time is needed for relative density of the corner to reach the maximum value,and the relative densities in every region improve evidently with increasing the pressure.The tensile stress was simulated to be the largest at the corner,and the hot tearings were forecasted to mainly appear at the corner too.By employing proper billet height and pressure,the extruded samples consisted of fine and uniform microstructures,and can obtain excellent mechanical properties and Brinell hardness.
基金Project(U1664252)supported by the National Natural Science Foundation of China
文摘The effect of dynamic recrystallization(DRX)on the microstructure and mechanical properties of 6063 aluminum alloy profile during porthole die extrusion was studied through experiment and simulation.The grain morphology was observed by means of electron backscatter diffraction(EBSD)technology.The results show that,at low ram speeds,increasing the ram speed caused an increase in DRX fraction due to the increase of temperature and strain rate.In contrast,at high ram speeds,further increasing ram speed had much less effect on the temperature,and the DRX faction decreased due to high stain rates.The microhardness and fraction of low angle boundaries in the welding zones were lower than those in the matrix zones.The grain size in the welding zone was smaller than that in the matrix zone due to lower DRX fraction.The decrease of grain size and increase of extrudate temperature were beneficial to the improvement of microhardness.
基金Project(zzyjkt2014-09)supported by the National Key Laboratory of High Performance and Complex Manufacturing,ChinaProject(2015GK3006)supported by Key R&D Program of Science and Technology Department of Hunan Province,China
文摘The 4-lobe aluminum alloy helical surface rotors are widely applied in industry,such as superchargers.Generally,the conventional manufacturing processes of aluminum alloy helical surface are time consuming and costly.To make the manufacturing processes more flexible and economical,the forward hot extrusion process is proposed to form the 4-lobe aluminum alloy helical surface rotors.In this work,we implement both simulations and experiments to the forming process of the helical surface,of which the material is 6063 aluminum alloy.The forward hot extrusion process is simulated with finite element method in DEFORM-3D.Based on the simulation method,the influences of different extrusion parameters,such as extrusion temperature,extrusion speed and extrusion ratio,on the extrusion process are studied.According to the numerical simulation results,the optimal case is chosen to carry out the experiment.Furthermore,the experimental results show that the surface is smooth;the toothed fill is full;the twist angle in the length direction is evenly distributed;the value of twist angle is roughly in line with the design angle,which is mainly due to the modified die structure,having a positive and significant effect on the increment of twist angle.Therefore,the twist angle has an increase of about 76%,which verifies the modified die structure.
文摘An innovative approach was introduced for the development of a AA6063 recrystallization model.This method incorporated a regression-based technique for the determination of material constants and introduced novel equations for assessing the grain size evolution.Calibration and validation of this methodology involved a combination of experimentally acquired microstructural data from the extrusion of three different AA6063 profiles and results from the simulation using the Qform Extrusion UK finite element code.The outcomes proved the agreement between experimental findings and numerical prediction of the microstructural evolution.The trend of the grain size variation based on different process parameters was accurately simulated,both after dynamic and static recrystallization,with an error of less than 25% in almost the whole sampling computations.
