It is difficult to directly electroplate Al on Mg alloys. The effects of pretreatment parameters on the corrosion resistance of films obtained on AZ31 Mg alloy surface were studied by using potentiodynamic polarizatio...It is difficult to directly electroplate Al on Mg alloys. The effects of pretreatment parameters on the corrosion resistance of films obtained on AZ31 Mg alloy surface were studied by using potentiodynamic polarization curves, to produce a compact interfacial layer as zinc-immersion deposition. After the substrate was pretreated under optimized conditions, aluminum was electrodeposited on AZ31 from TMPAC-AlCl3 room temperature ionic liquids. The depositions were characterized by scanning electron microscope equipped with energy dispersion X-ray. The results show that the traditional pretreatment of Mg alloys was successfully used for the Al-electroplating process from TMPAC-AlCl3 ionic liquids. The entire procedure includes alkaline cleaning, chemical pickling, surface activation （400 mL/L HF acid, 10 min）, zinc-immersion （20 min） and anhydrous treatment. A relatively compact zinc-immersion film was prepared on the substrate surface. A silvery-colored satin aluminum deposition was obtained on AZ31 from TMPAC-AlCl3 using direct current plating.展开更多
The effects of different Zn contents in Al-Mg alloy on the microstructure characterizations were observed by advanced electron microscopy and the corrosion properties were investigated by the inter-granular corrosion ...The effects of different Zn contents in Al-Mg alloy on the microstructure characterizations were observed by advanced electron microscopy and the corrosion properties were investigated by the inter-granular corrosion tests,the exfoliation corrosion tests,and the Potentiodynamic polarizaion tests.The τ phase(Mg_(32)(Al,Zn)_(49)) forms on the pre-existing Mn-rich particles and at the grain boundaries.According to the theory of binding energy,the formation of τ phase is much easier than that of β phase(Al_3Mg_2),somehow replacing β phase and reducing the possibility of β phase precipitation.This change dramatically decreases the susceptibility of corrosion.The Zn addition increases the corrosion resistance of Al-Mg alloy with an optimal value of 0.31%.When the Zn addition is increased to 0.78%,however,the corrosion resistance of alloy decreases once again but it is still better than that of the alloy without Zn addition.展开更多
The microstructures and mechanical properties of Al-6Zn-2Mg-1.5Cu-0.4Er alloy under different treatment conditions were investigated by transmission electron microscopy （TEM） observation, and tensile properties and ...The microstructures and mechanical properties of Al-6Zn-2Mg-1.5Cu-0.4Er alloy under different treatment conditions were investigated by transmission electron microscopy （TEM） observation, and tensile properties and hardness test, respectively. The relationship between mechanical properties and microstructures of the alloys was discussed. With trace Er addition to A1-Zn-Mg-Cu alloy, Er and Al interact to form Al3Er phase, which is coherent with a（A1） matrix. The results show that Al-Zn-Mg-Cu alloy after retrogression and re-ageing （RRA） heat treatment exhibits higher tensile strength, ductility and conductivity.展开更多
Effects of electromagnetic stirring on the microstructure and mechanical properties of the magnesium-lithium-aluminum alloy were studied.The results reveal that,the morphology of theαphase changes from the long block...Effects of electromagnetic stirring on the microstructure and mechanical properties of the magnesium-lithium-aluminum alloy were studied.The results reveal that,the morphology of theαphase changes from the long block to globular structure andβ phase distributes more widely in the periphery ofαphase when the electromagnetic stirring voltage is higher than 110 V.The mechanical properties are increased significantly with the increasing electromagnetic stirring.The tensile strength is improved from 172 to 195 MPa,and the elongation is increased from 10.65%to 25.75%.展开更多
文摘It is difficult to directly electroplate Al on Mg alloys. The effects of pretreatment parameters on the corrosion resistance of films obtained on AZ31 Mg alloy surface were studied by using potentiodynamic polarization curves, to produce a compact interfacial layer as zinc-immersion deposition. After the substrate was pretreated under optimized conditions, aluminum was electrodeposited on AZ31 from TMPAC-AlCl3 room temperature ionic liquids. The depositions were characterized by scanning electron microscope equipped with energy dispersion X-ray. The results show that the traditional pretreatment of Mg alloys was successfully used for the Al-electroplating process from TMPAC-AlCl3 ionic liquids. The entire procedure includes alkaline cleaning, chemical pickling, surface activation （400 mL/L HF acid, 10 min）, zinc-immersion （20 min） and anhydrous treatment. A relatively compact zinc-immersion film was prepared on the substrate surface. A silvery-colored satin aluminum deposition was obtained on AZ31 from TMPAC-AlCl3 using direct current plating.
基金Project(2011-006)supported by the State Administration of Science,Technology and Industry for National Defence,China
文摘The effects of different Zn contents in Al-Mg alloy on the microstructure characterizations were observed by advanced electron microscopy and the corrosion properties were investigated by the inter-granular corrosion tests,the exfoliation corrosion tests,and the Potentiodynamic polarizaion tests.The τ phase(Mg_(32)(Al,Zn)_(49)) forms on the pre-existing Mn-rich particles and at the grain boundaries.According to the theory of binding energy,the formation of τ phase is much easier than that of β phase(Al_3Mg_2),somehow replacing β phase and reducing the possibility of β phase precipitation.This change dramatically decreases the susceptibility of corrosion.The Zn addition increases the corrosion resistance of Al-Mg alloy with an optimal value of 0.31%.When the Zn addition is increased to 0.78%,however,the corrosion resistance of alloy decreases once again but it is still better than that of the alloy without Zn addition.
基金Project(2005CB623706) supported by the National Basic Research Program of China
文摘The microstructures and mechanical properties of Al-6Zn-2Mg-1.5Cu-0.4Er alloy under different treatment conditions were investigated by transmission electron microscopy （TEM） observation, and tensile properties and hardness test, respectively. The relationship between mechanical properties and microstructures of the alloys was discussed. With trace Er addition to A1-Zn-Mg-Cu alloy, Er and Al interact to form Al3Er phase, which is coherent with a（A1） matrix. The results show that Al-Zn-Mg-Cu alloy after retrogression and re-ageing （RRA） heat treatment exhibits higher tensile strength, ductility and conductivity.
基金Project(2009AA03Z525)supported by the National High-tech Research and Development Program of ChinaProject(NCET-08-0080)supported by the Program of New Century Excellent Talents of the Ministry of Education of ChinaProject(20082172)supported by the Natural Science Foundation of Liaoning Province,China
文摘Effects of electromagnetic stirring on the microstructure and mechanical properties of the magnesium-lithium-aluminum alloy were studied.The results reveal that,the morphology of theαphase changes from the long block to globular structure andβ phase distributes more widely in the periphery ofαphase when the electromagnetic stirring voltage is higher than 110 V.The mechanical properties are increased significantly with the increasing electromagnetic stirring.The tensile strength is improved from 172 to 195 MPa,and the elongation is increased from 10.65%to 25.75%.
