直流磁场下双金属复层铸坯制备

借助工程应用软件FLUENT誖,模拟研究了直流磁场对双金属复层铸坯制备过程金属液流动的影响规律,依据模拟优化的工艺参数,成功制得复层铝合金铸坯。结果表明,直流磁场可以有效抑制浇注入口金属液流速度,减少其射流深度,同时还可以有效控制铸型中心处出现的回流区;电磁制动效果随着磁场强度B增大而明显增加,但是当B达到某一临界值后,继续增加B,电磁制动效果增加幅度不大;在200mm·min-1的拉坯速度下给铸型宽度方向施加0.15T直流磁场,能使两种金属液体流动平稳,不发生混流。在此工艺参数下,实验中成功制备了双金属复层铝合金铸坯。

双金属铸焊复合辊套的制备工艺

介绍了一种低合金钢套筒与高铬铸铁工作层复合的双金属铸焊工艺。该工艺是在铸造好的套筒上堆焊一层熔点低于工作层的金属,通过电磁感应线圈的预热和浇注工作层金属液时的加热,以堆焊层为中间材质的过渡方式,将套筒与工作层均匀地复合在一起。结合Fe-Cr-C三元系液相线相图确定堆焊层成分,并采用正交试验的方法对堆焊工艺参数进行优化。通过COMSOL Multiphysics软件模拟不同预热温度时套筒的应力分布云图和感应加热温度场分布,对套筒的预热温度及预热时间进行选择。当工作层浇注温度1440℃,套筒预热温度900℃,感应加热时间60 s时,成功制备出熔合层均匀、无夹杂缺陷的铸焊复合辊套,验证了该工艺方法的可行性。

后磨牙树脂金属联合桩冠的临床应用

对破坏较大的后磨牙残冠及残根的修复,除传统的整铸金属桩冠修复外,近几年已有新的报道,但对修复体边缘位置问题存在不同的看法。笔者采用的树脂金属分层次制作的联合桩冠修复,由于充分利用了树脂的粘结性能,大大改善了修复体的固位和功能,经40例临床应用,效果良好。现介绍如下:

强韧性高铬铸铁磨球的研究与应用

通过对高铬铸铁的结晶特性的研究，采用金属型群铸工艺，控制高温奥氏作的相变温度，在铸态条件下，使20～50磨球获得合金奥氏体，使60～100磨球获得合金贝氏体＋屈氏体，这两种基体上都均匀分布着精细的M7C3型碳化物，经时效处理后用于工业生产。经各类球磨机使用证明，磨球强度高、韧性好、耐磨性能优良。

Microstructure and mechanical properties of Mg-Gd-Y-Zr alloy cast by metal mould and lost foam casting

The microstructure and mechanical properties of Mg-10.1Gd-3.74Y-0.25Zr （mass fraction, %） alloy （GW104 alloy） cast by metal mould casting （MMC） and lost foam casting （LFC） were evaluated, respectively. It is revealed that different forming modes do not influence the phase composition of as-cast alloy. In the as-cast specimens, the microstructures are similar and composed of α-Mg solid solution, eutectic compound of α-Mg＋Mg 24 （Gd, Y） 5 and cuboid-shaped Mg 5 （Gd, Y） phase; whereas the average grain size of the alloy produced by metal mould casting is smaller than that by lost foam casting. The eutectic compound of the alloy is completely dissolved after solution treatment at 525 ℃for 6 h, while the Mg 5 （Gd, Y） phase still exists after solution treatment. After peak-ageing, the lost foam cast alloy exhibits the maximum ultimate tensile strength of 285 MPa, and metal mould cast specimen 325 MPa at room temperature, while the tensile yield strengths of them are comparable. It can be concluded that GW104 alloy cast by lost foam casting possesses similar microstructure and evidently lower mechanical strength compared with metal mould cast alloy, due to slow solidification rate and proneness to form shrinkage porosities during lost foam casting process.

Microstructure and crystal growth direction of Al-Cu alloy

The microstructures and crystal growth directions of permanent mould casting（PMC） and directionally solidified（DS） Al-Cu alloys with different contents of Cu were investigated. Simultaneously, the effects of pouring temperature on the microstructure and crystal growth direction of permanent mould casting pure Al were also discussed. The results indicate that the α（Al） crystals in the pure Al do not always keep common columnar grains, but change from the columnar grains to columnar dendrites with developed arms as the pouring temperature rises. The growth direction also varies with the change of pouring temperature. Cu element has similar effects on the microstructures of the PMC and DS casting Al-Cu alloys and the α（Al） crystals gradually change from columnar crystals in turn to columnar dendrites and developed equiaxed dendrites as the Cu content increases. The crystal growth direction in the PMC alloys gradually approaches （110） orientation with increasing Cu content. But the resulting crystals with growth direction of （110） do not belong to feathery grains. There are also no feathery grains to form in all of the DS Al-Cu alloys.

INVESTIGATION OF FOAM-METAL INTERFACE BEHAVIORS DURING MOLD FILLING OF MAGNESIUM ALLOY LFC PROCESS

The visual observation of the mold filling and the standard analysis-of-variance （ANOVA） for the velocity of the filling metal are conducted to study foam-metal interface behaviors during the mold filling of the lost foam casting （LFC） process of the magnesium alloy. Results show that the foam primarily melts into liquid products instead of gasifying at the pouring temperature of the magnesium alloy. Without the vacuum, the metal fills smoothly with a slightly convex metal front, and the velocity of the filling metal is low and continually decreases as the foam is displaced. The mold filling is governed by the removal of foam decomposition products at the foam-metal interface. However, when the vacuum is applied, the mold filling is controlled by the foam decomposition rate at the foam-metal interface. A pronounced irregular and concave metal front is formed. The velocity of the metal front varies tremendously during the mold filling process and is ruleless. The metal velocity increases rapidly, and the vacuum shows a strong interaction effect with the pouring temperature on the metal velocity. As the vacuum continues to increase, the pouring temperature becomes the most significant factor for the mold filling, while both the vacuum effect and the interaction effect between the vacuum and the pouring temperature on the metal velocity are substantially reduced. Based on experimental results, a model for the foam thermal degradation and the removal of decomposition products occurred at the foam-metal interface is presented during the mold filling of the magnesium alloy LFC process under the vacuum.

An Alternative Method for SU-8 Removal Using PDMS Technique

An alternative method for SU-8 removal is proposed.Instead of directly using SU-8 microstructure as the electroplating mold,a polydimethysiloxane (PDMS) replica is employed.The metallic micromold insert obtained through this method can be easily peeled off from the PDMS replica,meanwhile with high resolution and smooth surfaces.

Microstructures and properties of A356-10%SiC particle composite castings at different solidification pressures

A356-based metal matrix composites with 10% SiC particles of 10 rtm were fabricated by stir casting and direct squeeze casting process under applied pressures of 0.1 （gravity）, 25, 50 and 75 MPa. The microstructures and mechanical properties of the as-cast and T6 heat-treated castings were investigated. The results show that as the applied pressures increase, the casting defects as particle-porosity clusters reduce and the incorporation between the particles and matrix can be improved. The tensile strength, hardness, and coefficients of thermal expansion （CTE） increase with the increase of the pressures. Compared with the as-cast composite castings, the tensile strength and hardness of the heat-treated casting are improved whereas CTEs tend to decrease in T6-treated condition. For the gravity cast composites, there are some particle-porosity clusters on the fracture surface, and the clusters are hardly detected on the fracture surface of the samples solidified at the external pressures. Different fracture behaviors are found between the composites solidified at the gravity and imposed pressures.

Fabrication and characterization of stir casting AA6061-31%B_4C composite

A sophisticated stir casting route to fabricate large scale AA6061-31%B4C composite was developed. Key process parameters were studied, microstructure and mechanical properties of the composite were investigated. The results indicated that vacuum stirring/casting, B4C/Mg feeding and ingots cooling were essential to the successful fabrication of AA6061-31%B4C composite. Chemical erosion examination verified the designed B4 C content; X-ray fluorescence spectrometer（XFS） showed the chemical composition of Mg and Si in the matrix conformed to industry standards; scanning electronic microscope（SEM） and X-ray diffraction（XRD） revealed that B4 C particles were evenly distributed in the composites with well dispersed Mg2Si precipitates. Tensile testing results showed that the AA6061-31%B4C composite had a tensile strength of 340 MPa, improved by 112.5% compared with AA1100-31%B4C composite, which is attributed to the enhanced strength of the matrix alloy.

简述中国封建社会的通货膨胀

通货膨胀是社会经济生活反常中出现的一种怪物。在中国两千多年的封建社会中,历代统治者为了解脱经济危机,采取通过货币减铸金属重量、改铸大面额钱币。

牵线搭桥

【正】 七彩冷瓷是国内新近流行的高档装饰涂料。(1)适用新旧内外墙和地面以及铁、木器的涂饰;(2)不用抛光和压光直接刷滚就光亮如镜;(3)可制作色彩繁多的宝丽板、壁纸、天花板、花岗岩和地板砖图案,达到乱真效果;(4)水刷万次无损,用抹布越擦越亮;(5)坚硬耐磨;(6)耐酸碱;(7)防火阻燃;(8)无毒无味无污染。

Microstructure and properties of Al/Cu bimetal in liquid-solid compound casting process

A Ni-P coating was deposited on Cu substrate by electroless plating and the Al/Cu bimetal was produced by solid？liquid compound casting technology. The microstructure, mechanical properties and conductivity of Al/Cu joints with different process parameters （bonding temperature and preheating time） were investigated. The results showed that intermetallics formed at the interface and the thickness and variety increased with the increase of bonding temperature and preheating time. The Ni？P interlayer functioned as a diffusion barrier and protective film which effectively reduced the formation of intermetallics. The shear strength and conductivity of Al/Cu bimetal were reduced by increasing the thickness of intermetallics. In particular, the detrimental effect of Al2Cu phase was more obvious compared with the others. The sample preheated at 780 ℃ for 150 s exhibited the maximum shear strength and conductivity of 49.8 MPa and 5.29×10^5 S/cm, respectively.

Optimization of process parameters for in situ casting of Al/TiB_2 composites through response surface methodology

The mathematical models were developed to predict the ultimate tensile strength （UTS） and hardness of Al/TiB2 MMCs fabricated by in situ reaction process. The process parameters include temperature, reaction time and mass fraction of TiB2. The in-situ casting was carried out based on three-factor five-level central composite rotatable design using response surface methodology （RSM）. The validation of the model was carried out using ANOVA. The mathematical models developed for the mechanical properties were predicted at 95% confidence limit.

Microstructure and properties of high silicon aluminum alloy with 2% Fe prepared by rheo-casting

The morphology changes of both Fe-containing intermetallic compounds and the primary Si phase of Al-20Si-2Fe- 2Cu-0.4Mg-1.0Ni-0.5Mn （mass fraction, %） alloy produced by semi-solid rheo-diecasting were studied. The semi-solid slurry of high silicon aluminum alloy was prepared by direct ultrasonic vibration （DUV） which was imposed on the alloy near the liquidus temperature for about 2 rain. Then, standard test samples of 6.4 mm in diameter were formed by semi-solid rheo-diecasting. The results show that the DUV treatment suppresses the formation of needle-like ,β-Al5（Fe,Mn）Si phase, and the Fe-containing intermetallic compounds exist in the form of fine Al4（Fe, Mn）Si2 particles. Additionally, the primary Si grows up as fine and round particles with uniform distribution in α（Al） matrix of this alloy under DUV treatment. The tensile strengths of the samples at the room temperature and 573 K are 230 MPa and 145 MPa, respectively. The coefficient of thermal expansion （CTE） between 25 ℃ and 300 ℃ is 16.052 8×10^-6 ℃^-1, and the wear rate is 1.55%. The hardness of this alloy with 2% Fe reaches HB146.3. It is discovered that modified morphology and uniform distribution of the Fe-containing intermetallic compounds and the primary Si phase are the main reasons for reducing the CTE and increasing the wear resistance of this alloy.

Purification technology of molten aluminum

Various purification methods were explored to eliminate the dissolved hydrogen and nonmetallic inclusions from molten aluminum alloys. A novel rotating impeller head with self-oscillation nozzles or an electromagnetic valve in the gas circuit was used to produce pulse gas currents for the rotary impeller degassing method. Water simulation results show that the size of gas bubbles can be decreased by 10%20% as compared with the constant gas current mode. By coating ceramic filters or particles with active flux or enamels, composite filters were used to filter the scrap A356 alloy and pure aluminum. Experimental results demonstrate that better filtration efficiency and operation performance can be obtained. Based on numerical calculations, the separation efficiency of inclusions by high frequency magnetic field can be significantly improved by using a hollow cylinder-like separator or utilizing the effects of secondary flow of the melt in a square separator. A multi-stage and multi-media purification platform based on these methods was designed and applied in on-line processing of molten aluminum alloys. Mechanical properties of the processed scrap A356 alloy are greatly improved by the composite purification.

Fatigue crack growth mechanism in cast hybrid metal matrix composite reinforced with SiC particles and Al_2O_3 whiskers

The fatigue crack growth(FCG) mechanism of a cast hybrid metal matrix composite(MMC) reinforced with SiC particles and Al2O3 whiskers was investigated. For comparison, the FCG mechanisms of a cast MMC with Al2O3 whiskers and a cast Al alloy were also investigated. The results show that the FCG mechanism is observed in the near-threshold and stable-crack-growth regions.The hybrid MMC shows a higher threshold stress intensity factor range, ?Kth, than the MMC with Al2O3 and Al alloy, indicating better resistance to crack growth in a lower stress intensity factor range, ?K. In the near-threshold region with decreasing ?K, the two composite materials exhibit similar FCG mechanism that is dominated by debonding of the reinforcement–matrix interface, and followed by void nucleation and coalescence in the Al matrix. At higher ?K in the stable- or mid-crack-growth region, in addition to the debonding of the particle–matrix and whisker–matrix interface caused by cycle-by-cycle crack growth at the interface, the FCG is affected predominantly by striation formation in the Al matrix. Moreover, void nucleation and coalescence in the Al matrix and transgranular fracture of SiC particles and Al2O3 whiskers at high ?K are also observed as the local unstable fracture mechanisms.However, the FCG of the monolithic Al alloy is dominated by void nucleation and coalescence at lower ?K, whereas the FCG at higher ?K is controlled mainly by striation formation in the Al grains, and followed by void nucleation and coalescence in the Si clusters.

Effect of different casting methods on microstructure and mechanical properties of Mg-10Gd-3Y-0.6Zr alloy

The effects of two different casting methods on the microstructures and mechanical properties of as-cast and T6-cast states of Mg-10Gd-3Y-0.6Zr alloy were studied by using metal mold casting and squeeze casting.The results show that the microstructure of Mg-10Gd-3Y-0.6Zr alloy is mainly composed ofα-Mg primary phase and Mg 24(Gd,Y)5 eutectic phase.The squeeze cast grains are small with a dendrite like morphology,and the tensile strength of the alloy in T6 state can reach 285 MPa.While the metal grains are coarse,the eutectic phases are distributed in the grain boundary,and the tensile strength of the alloy in T6 state is only 250 MPa.

Orthogonal tests of lead-clad tin bimetal continuous casting by air pressure core-filling

To provide theoretical basis and practical guidance for preparing composite rods of external diameter no larger than 12 mm by directly continuous casting,low melting point materials of lead and tin were selected to prepare composite rods of external diameter 12 mm and inner diameter 8 mm with air pressing core filled continuous casting process.The orthogonal tests consisting of three factors and three levels were designed to investigate the parameters of melting lead temperature,continuous casting speed and air pressure that affect the performance of the composite rods.The results show that melting lead temperature is the most important factor that influences the solid/liquid interface location;continuous casting speed is the most important factor that influences the surface quality and lead and tin inter-diffusion amount;air pressure can improve the surface quality obviously and make the rods easily drawn out,but the surface quality cannot get obvious improvement when the air pressure is above 0.03 MPa.The composite rods have excellent surface quality,obvious intermediate layer,even thick clad,and metallurgical bonding interface under the condition of melting lead temperature of 375 °C,continuous casting speed of 10 mm/min,and air pressure of 0.03 MPa.