YG类硬质合金中钴镍合量的测定

研究了 YG类硬质合金中钴镍合量的测定条件 ,建立了分析方法 ,克服了原测定钴分析方法不能满足生产的弊端 。

Research and Development of Heat-Resistant Materials for Advanced USC Power Plants with Steam Temperatures of 700℃ and Above

Materials-development projects for advanced ultra-supercritical(A-USC) power plants with steam temperatures of 700℃ and above have been performed in order to achieve high efficiency and low CO_2 emissions in Europe, the US, Japan, and recently in China and India as well. These projects involve the replacement of martensitic 9%–12% Cr steels with nickel(Ni)-base alloys for the highest temperature boiler and turbine components in order to provide sufficient creep strength at 700℃ and above. To minimize the requirement for expensive Ni-base alloys, martensitic 9%–12% Cr steels can be applied to the next highest temperature components of an A-USC power plant, up to a maximum of 650℃. This paper comprehensively describes the research and development of Ni-base alloys and martensitic 9%–12% Cr steels for thick section boiler and turbine components of A-USC power plants, mainly focusing on the long-term creep-rupture strength of base metal and welded joints, strength loss in welded joints, creep-fatigue properties, and microstructure evolution during exposure at elevated temperatures.

Effects of heat treatment on microstructure and mechanical properties of Inconel 625 alloy fabricated by wire arc additive manufacturing process

The microstructure and mechanical properties of Inconel 625 alloy fabricated by wire arc additive manufacturing process were evaluated under as-prepared and heat-treated conditions.A dendritic Ni-based solid solution phase along with(Nb,Ti)C carbide,Laves,and δ-Ni3Nb secondary phases were developed in the microstructure of the as-prepared alloy.Solution heat treatment led to the dissolution of Laves and Ni3Nb phases.In addition,dendrites were replaced with large columnar grains.Aging heat treatment resulted in the formation of grain boundary M23C6 carbide and nanometric γ''precipitates.Hardness,yield and tensile strengths,as well as elongation of the as-prepared part,were close to those of the cast alloy and its fracture occurred in a transgranular ductile mode.Solution heat treatment improved hardness and yield strength and declined the elongation,but it did not have a considerable impact on the tensile strength.Furthermore,aging heat treatment caused the tensile properties to deteriorate and changed the fracture to a mixture of transgranular ductile and intergranular brittle mode.

Synthesis of flowerlike nickel particles and their microwave absorbing properties

Two kinds of nickel particles with flower-like struc~＇es assembled with a number of nano-flakes were synthesized and the relationship of their morphology and microwave absorbing properties was studied. The electromagnetic parameters of these flower-like Ni were measured with vector network analyzer at 2-18 GHz frequency and the reflection losses （RL） with different sample thicknesses were calculated. The results indicate that the flower-like nickel-wax composites with the sample thickness less than 2 mm show excellent absorbing ability. This result is expected to play a guiding role in the preparation of the highly efficient absorber.

Kinetics of acid-oxygen leaching of low-sulfur Ni-Cu matte at atmospheric pressure

The leaching of low-sulfur Ni-Cu matte in acid-oxygen(CuSO4-H2SO4-O2)solution at atmospheric pressure was researched.This matte was obtained from high grade Ni-Cu matte by magnetic separation,which mainly contained Ni-Cu alloy and a small quantity of sulfides.The effects of temperature,agitation speed,oxygen flow rate,particle size,acid concentration and concentration of copper ion were studied.It is found that the matte particles are leached by shrinking core mechanism and the leaching process is electrochemically controlled.In a temperature range of 30-60℃,the surface reaction is rate-limiting step,with an apparent activation energy of 41.9 kJ/mol.But at higher temperature(70-85℃),the rate process is controlled by diffusion through the product layer,with an apparent activation energy of 7.3 kJ/mol.

Influence of Chemical Effect on the Kβ/Kα Intensity Ratios and Kβ Energy Shift of Co, Ni, Cu, and Zn Complexes

Chemical effects on the Kβ/Kα intensity ratios and △E energy differences for Co, Ni, Cu, and Zn complexes were investigated. The samples were excited by 59.5 keV γ-rays from a ^241Am annular radioactive source. K X-rays emitted by samples were counted by an Ultra-LEGe detector with a resolution of 150 eV at 5.9 keV. We observed the effects of different ligands on the Kβ/Kα intensity ratios and △E energy differences for Co, Ni, Cu, and Zn complexes. We tried to investigate chemical effects on central atoms using the behaviors of different ligands in these complexes. The experimental values of Kβ/Kα were compared with the theoretical and other experimental values of pure Co, Ni, Cu, and Zn.

Forced Convective Heat Transfer Experiment of Supercritical Water in Different Diameter of Tubes

Forced convective experiment of supercritical water was performed in Inconel-625 tubes of 4.62 mm, 7.98 mm and 10.89 mm in diameter. The water flowed upward, covering the ranges of pressure of 23.4 MPa to 25.8 MPa, mass flux of 90 kg/m^2s to 3,281 kg/m^2s, local bulk temperature of 102-384 ℃, inner wall temperature of 167-669℃ and heat flux of up to 2.41 MW/m^2. The results exhibited severe deteriorated and enhancement heat transfer. The experimental results can be calculated by the Jackson＇s correlation and the Bishop＇s correlation mostly. But some data with strong effects of the buoyancy force and the variations of flow regimes can not be predicted properly.

New Silver Nanosensor for Nickel Traces： Synthesis, Characterization and Analytical Parameters

A new fluorescence silver nanosensor assisted by surfactant has been synthesized and applied to ultra trace nickel determination. Operational variables which influence nanomaterial synthesis have been studied and optimized. Synthesis was very fast and simple using non polluting solvents; silver chemical reduction was carried out at room temperature. Spectroscopic studies were carried out in order to assure the uniformed of nanomaterial obtained. Fluorescent signal of silver nanoparticles resulted enhanced in presence of Ni（II）. At optimal experimental conditions, a detection limit of 0.036 pg＇L1 and quantification limit 0.12 pg＇L~ were obtained. The calibration sensitivity was 2 x 1014 L.pg-l.cm1 for the new methodology, with a range of linearity of six orders of magnitude between 0.12 and 2.93 × 10^5 pg L^-1. The tolerance levels for potential interferent ions were studied with good results. The proposed methodology represents a promising approach for Ni（II） traces quantification due to its low operation cost, simplicity of instrumentation, high sampling speed and non-polluting solvents.

Thermodynamic prediction of metastable phases of Ni-Ti system formed by ion beam mixing

By taking into account the valence electron number and periodic number of constituting metals, a new method is first proposed to calculate the structural enthalpy in the Miedema's model and the modified Miedema's model is then used to predict the formation of metastable phases in Ni-Ti system. To testify the relevance of the present prediction, the multilayered films of Ni1-xTix (x=27.3, 30.5, 42.4, 83.1, 89) are prepared and irradiated by 200 keV xenon ions. Experiment results reveal that uniform amorphous phases are obtained in the Ni72.7Ti27.3, Ni69.5Ti30.5, and Ni57.6Ti42.4 films by increasing the irradiation dose. While for the Ni16.9Ti83.1 and Ni11Ti89 films, an hcp Ti-based solid solution phase and a bcc Ti-rich solid solution phase coexist upon irradiation dose higher than 6×1014 Xe+/cm2. The predictions of relative stabilities of metastable phases in Ni-Ti system by the modified Miedema's model match well with IBM experiments, thus justifying the modification proposed in the present study.

Sulfur/nickel ferrite composite as cathode with high-volumetric-capacity for lithium-sulfur battery

Low volumetric energy density is a bottleneck for the application of lithium-sulfur (Li-S)battery.The low- density sulfur cooperated with the light-weight carbon sub- strate realizes electrochemical cycle stability,but leads to worse volumetric energy density.Here,nickel ferrite (NiFe2O4)nanofibers as novel substrate for sulfur not only anchor lithium polysulfides to enhance the cycle stability of sulfur cathode,but also contribute to the high volumetric capacity of the S/nickel ferrite composite.Specifically,the S/ nickel ferrite composite presents an initial volumetric capacity of 1,281.7mA h cm^-3-composite at 0.1C rate,1.9times higher than that of S/carbon nanotubes,due to the high tap density of the S/nickel ferrite composite.