The influence of Ga and Bi on the microstructure and electrochemical performance of Al-7Zn-0.1Sn （mass fraction,%） sacrificial anodes was investigated by means of optical microscopy （OM）,scanning electron microsco...The influence of Ga and Bi on the microstructure and electrochemical performance of Al-7Zn-0.1Sn （mass fraction,%） sacrificial anodes was investigated by means of optical microscopy （OM）,scanning electron microscopy/energy dispersive X-ray analysis （SEM/EDAX） and electrochemical measurements.It was found that the coarse dendrites structure transformed into the equiaxed grains as well as a small amount of dendrite grains after adding Ga and Bi into Al-Zn-Sn alloys.A high current efficiency of 97% and even corrosion morphology were obtained for Al-7Zn-0.1Sn-0.015Ga-0.1Bi alloy.The results indicate that the proper amount of Ga and Bi is effective on improving the microstructure and electrochemical performance of Al-Zn-Sn alloy.展开更多
Electrochemical impendence spectroscopy （EIS） is applied to investigate the dissolution behavior of Al-Zn alloys in 3% NaCl solution at different polarization potentials. A new reaction model is proposed, and the ac...Electrochemical impendence spectroscopy （EIS） is applied to investigate the dissolution behavior of Al-Zn alloys in 3% NaCl solution at different polarization potentials. A new reaction model is proposed, and the activation mechanism of zinc in Al-Zn alloys is achieved. There are three intermediates in the dissolution process： Znad^＋, Znad^2＋ and Alad^＋, ,of which only Zni can activate Al-Zn alloys. Most Znnd^＋ is produced by β-phase,and the alloys with 2. 3% - 3. 8% （wt） Zn dissolve rapidly. The Al-Zn alloys of heart-shaped EIS are active in 3% NaCl solution, thus EIS characteristic can be used to distinguish the activa-tion of Al-Zn alloys.展开更多
The electrical performance including breakdown voltage and turn-off speed of SOI-LIGBT is improved by incorporating a resistive field plate (RFP) and a p-MOSFET.The p-MOSFET is controlled by a signal detected from a p...The electrical performance including breakdown voltage and turn-off speed of SOI-LIGBT is improved by incorporating a resistive field plate (RFP) and a p-MOSFET.The p-MOSFET is controlled by a signal detected from a point of the RFP.During the turning-off of the IGBT,the p-MOSFET is turned on,which provides a channel for the excessive carriers to flow out of the drift region and prevents the carriers from being injected into the drift region.At the same time,the electric field affected by the RFP makes the excessive carriers flow through a wider region,which almost eliminates the second phase of the turning-off of the SOI-LIGBT caused by the substrate bias.Faster turn-off speed is achieved by above two factors.During the on state of the IGBT,the p-MOSFET is off,which leads to an on-state performance like normal one.At least,the increase of the breakdown voltage for 25% and the decrease of the turn-off time for 65% can be achieved by this structure as can be verified by the numerical simulation results.展开更多
The article improves the process of dielectric barrier discharge(DBD)activated anode bonding.The treated surface was characterized by the hydrophilic surface test.The results showed that the hydrophilic angle was sign...The article improves the process of dielectric barrier discharge(DBD)activated anode bonding.The treated surface was characterized by the hydrophilic surface test.The results showed that the hydrophilic angle was significantly reduced under nano-gap conditions and the optimal discharge voltage was 2 kV.Then,the anodic bonding and dielectric barrier discharge activated bonding were performed in comparison experiments,and the bonding strength was characterized by tensile failure test.The results showed that the bonding strength was higher under the nano-gap dielectric barrier discharge.This process completed 110°C ultra-low temperature anodic bonding and the bonding strength reached 2 MPa.Finally,the mechanism of promoting bonding after activation is also discussed.展开更多
Zirconium oxide nanoparticles with 0.4 wt.%and 0.8 wt.%are incorporated into the Al-0.65 Mg-0.05 Ga-0.15 Sn(wt.%)alloy anode(base alloy)in order to improve the performance of the resulting anodes.Electrochemical chara...Zirconium oxide nanoparticles with 0.4 wt.%and 0.8 wt.%are incorporated into the Al-0.65 Mg-0.05 Ga-0.15 Sn(wt.%)alloy anode(base alloy)in order to improve the performance of the resulting anodes.Electrochemical characterization of the reinforced alloys was done by potentiodynamic polarization,electrochemical impedance spectroscopy and galvanostatic discharge and corrosion behavior was evaluated using self-corrosion rate and hydrogen evolution in 4 mol/L KOH solution.The surface morphology of the alloys was also studied using field emission scanning electron microscope(FESEM).The obtained results indicate that the base alloy shows high corrosion rate in 4 mol/L KOH solution by releasing 0.47 m L/(min·cm^2)hydrogen gas,whereas the alloy containing 0.8 wt.%Zr O2 provides the lowest hydrogen evolution rate by releasing 0.32 m L/(min·cm^2)hydrogen gas.Furthermore,by increasing zirconium oxide nanoparticles,the corrosion current density of the aluminum anodes is decreased and their corrosion resistance increases significantly compared to the base alloy in alkaline solution.In addition,nanometer-sized zirconium oxide incorporated anodes exhibit the improved galvanic discharge efficiencies,so that 0.8 wt.%nano-zirconium oxide incorporated base alloy displays the highest power density and anodic utilization compared with the others in 4 mol/L KOH solution.展开更多
Mg-6%Al-5%Pb(mass fraction) anodes with different contents of zinc were prepared by melting and casting.The electrochemical discharge behavior of these anodes in 3.5% NaCl solutions was investigated by galvanostatic t...Mg-6%Al-5%Pb(mass fraction) anodes with different contents of zinc were prepared by melting and casting.The electrochemical discharge behavior of these anodes in 3.5% NaCl solutions was investigated by galvanostatic test and electrochemical impedance spectroscopy(EIS).The microstructures and the corroded surfaces of these anodes were studied by scanning electron microscopy(SEM) and emission spectrum analysis(ESA).The phase structures and the corrosion products of the anodes were analyzed by X-ray diffraction(XRD).The results show that zinc promotes the grain refinement of Mg-6%Al-5%Pb anode and makes the average discharge potential of Mg-6%Al-5%Pb anode more negative during galvanostatic test.Mg-6%Al-5%Pb anode with the addition of 1%(mass fraction) zinc has the best electrochemical performance.The activation mechanism of zinc to Mg-6%Al-5%Pb anode is as follows:The hydrolyzation of dissolved Zn2+ ions reduces the pH value of the solution near the surface of the anode and accelerates the dissolution of Mg(OH)2 film;The precipitated Zn(OH)2 with similar structure as Mg(OH)2 combines with Mg(OH)2 film easily and makes it break down.展开更多
Experimental research of anode current and anode voltage influence on the speed of decaying plasma resistance change and the time ofthyratron cutoff. Anode current resistance increase is shown to cause thyratron cutof...Experimental research of anode current and anode voltage influence on the speed of decaying plasma resistance change and the time ofthyratron cutoff. Anode current resistance increase is shown to cause thyratron cutoff time increase in case of fixed anode voltage. In turn anode voltage increase in case of fixed anode current causes earlier increase of decaying plasma resistance growth speed and quicker apparatus cutoff：展开更多
Ni-Fe/Cu/Co/Cu multilayered nanowire arrays were electrodeposited into anodic aluminum oxide template by using dual-bath method at room temperature. Scanning electron microscopy and transmission electron microscopy we...Ni-Fe/Cu/Co/Cu multilayered nanowire arrays were electrodeposited into anodic aluminum oxide template by using dual-bath method at room temperature. Scanning electron microscopy and transmission electron microscopy were used to characterize the morphology and structure of the multilayered nanowire arrays. Vibrating sample magnetometer and physical property measurement system were used to measure their magnetic and giant magnetoresistance （GMR） properties. The effect of sub-layer thickness on the magnetic and GMR properties was investigated. The results indicate that magnetic properties of electmdeposited nanowires are not affected obviously by Cu layer thickness, while magnetic layers （Ni-Fe and Co layers） have significant influence. In addition, GMR ratio presents an oscillatory behavior as Cu layer thickness changes. The magnetic and GMR properties of the multilayered nanowire arrays are optimum at room temperature for the material structure of Ni-Fe （25 nm）/Cu （15 nm）/Co （25 nm）/Cu （15 nm） with 30 deposition cycles.展开更多
基金Project(094200510019) supported by Technology Creative Programmer of Henan for Excellent Talents,ChinaProject(092300410132) supported by the Natural Science Foundation of Henan Province,China
文摘The influence of Ga and Bi on the microstructure and electrochemical performance of Al-7Zn-0.1Sn （mass fraction,%） sacrificial anodes was investigated by means of optical microscopy （OM）,scanning electron microscopy/energy dispersive X-ray analysis （SEM/EDAX） and electrochemical measurements.It was found that the coarse dendrites structure transformed into the equiaxed grains as well as a small amount of dendrite grains after adding Ga and Bi into Al-Zn-Sn alloys.A high current efficiency of 97% and even corrosion morphology were obtained for Al-7Zn-0.1Sn-0.015Ga-0.1Bi alloy.The results indicate that the proper amount of Ga and Bi is effective on improving the microstructure and electrochemical performance of Al-Zn-Sn alloy.
基金National Natural Science Foundation of China(Nos.51204147,51274175,51574206,51574207)Program for International S&T Cooperation Projects of China(No.2014DFA50320)+1 种基金Program for International S&T Cooperation Projects of Shanxi Province(No.201381017)Technological Projects of Shanxi Province(No.20150313002-3)
文摘Electrochemical impendence spectroscopy （EIS） is applied to investigate the dissolution behavior of Al-Zn alloys in 3% NaCl solution at different polarization potentials. A new reaction model is proposed, and the activation mechanism of zinc in Al-Zn alloys is achieved. There are three intermediates in the dissolution process： Znad^＋, Znad^2＋ and Alad^＋, ,of which only Zni can activate Al-Zn alloys. Most Znnd^＋ is produced by β-phase,and the alloys with 2. 3% - 3. 8% （wt） Zn dissolve rapidly. The Al-Zn alloys of heart-shaped EIS are active in 3% NaCl solution, thus EIS characteristic can be used to distinguish the activa-tion of Al-Zn alloys.
文摘The electrical performance including breakdown voltage and turn-off speed of SOI-LIGBT is improved by incorporating a resistive field plate (RFP) and a p-MOSFET.The p-MOSFET is controlled by a signal detected from a point of the RFP.During the turning-off of the IGBT,the p-MOSFET is turned on,which provides a channel for the excessive carriers to flow out of the drift region and prevents the carriers from being injected into the drift region.At the same time,the electric field affected by the RFP makes the excessive carriers flow through a wider region,which almost eliminates the second phase of the turning-off of the SOI-LIGBT caused by the substrate bias.Faster turn-off speed is achieved by above two factors.During the on state of the IGBT,the p-MOSFET is off,which leads to an on-state performance like normal one.At least,the increase of the breakdown voltage for 25% and the decrease of the turn-off time for 65% can be achieved by this structure as can be verified by the numerical simulation results.
基金Project(6140863020216JW30001)supported by the General Armaments Department Pre-research Fund,China。
文摘The article improves the process of dielectric barrier discharge(DBD)activated anode bonding.The treated surface was characterized by the hydrophilic surface test.The results showed that the hydrophilic angle was significantly reduced under nano-gap conditions and the optimal discharge voltage was 2 kV.Then,the anodic bonding and dielectric barrier discharge activated bonding were performed in comparison experiments,and the bonding strength was characterized by tensile failure test.The results showed that the bonding strength was higher under the nano-gap dielectric barrier discharge.This process completed 110°C ultra-low temperature anodic bonding and the bonding strength reached 2 MPa.Finally,the mechanism of promoting bonding after activation is also discussed.
文摘Zirconium oxide nanoparticles with 0.4 wt.%and 0.8 wt.%are incorporated into the Al-0.65 Mg-0.05 Ga-0.15 Sn(wt.%)alloy anode(base alloy)in order to improve the performance of the resulting anodes.Electrochemical characterization of the reinforced alloys was done by potentiodynamic polarization,electrochemical impedance spectroscopy and galvanostatic discharge and corrosion behavior was evaluated using self-corrosion rate and hydrogen evolution in 4 mol/L KOH solution.The surface morphology of the alloys was also studied using field emission scanning electron microscope(FESEM).The obtained results indicate that the base alloy shows high corrosion rate in 4 mol/L KOH solution by releasing 0.47 m L/(min·cm^2)hydrogen gas,whereas the alloy containing 0.8 wt.%Zr O2 provides the lowest hydrogen evolution rate by releasing 0.32 m L/(min·cm^2)hydrogen gas.Furthermore,by increasing zirconium oxide nanoparticles,the corrosion current density of the aluminum anodes is decreased and their corrosion resistance increases significantly compared to the base alloy in alkaline solution.In addition,nanometer-sized zirconium oxide incorporated anodes exhibit the improved galvanic discharge efficiencies,so that 0.8 wt.%nano-zirconium oxide incorporated base alloy displays the highest power density and anodic utilization compared with the others in 4 mol/L KOH solution.
基金Project(JPPT-115-168) supported by the National Key Science and Technological Program of China
文摘Mg-6%Al-5%Pb(mass fraction) anodes with different contents of zinc were prepared by melting and casting.The electrochemical discharge behavior of these anodes in 3.5% NaCl solutions was investigated by galvanostatic test and electrochemical impedance spectroscopy(EIS).The microstructures and the corroded surfaces of these anodes were studied by scanning electron microscopy(SEM) and emission spectrum analysis(ESA).The phase structures and the corrosion products of the anodes were analyzed by X-ray diffraction(XRD).The results show that zinc promotes the grain refinement of Mg-6%Al-5%Pb anode and makes the average discharge potential of Mg-6%Al-5%Pb anode more negative during galvanostatic test.Mg-6%Al-5%Pb anode with the addition of 1%(mass fraction) zinc has the best electrochemical performance.The activation mechanism of zinc to Mg-6%Al-5%Pb anode is as follows:The hydrolyzation of dissolved Zn2+ ions reduces the pH value of the solution near the surface of the anode and accelerates the dissolution of Mg(OH)2 film;The precipitated Zn(OH)2 with similar structure as Mg(OH)2 combines with Mg(OH)2 film easily and makes it break down.
文摘Experimental research of anode current and anode voltage influence on the speed of decaying plasma resistance change and the time ofthyratron cutoff. Anode current resistance increase is shown to cause thyratron cutoff time increase in case of fixed anode voltage. In turn anode voltage increase in case of fixed anode current causes earlier increase of decaying plasma resistance growth speed and quicker apparatus cutoff：
基金Supported by the Natural Science Foundation of Tianjin,China(08JCZDJC17400)
文摘Ni-Fe/Cu/Co/Cu multilayered nanowire arrays were electrodeposited into anodic aluminum oxide template by using dual-bath method at room temperature. Scanning electron microscopy and transmission electron microscopy were used to characterize the morphology and structure of the multilayered nanowire arrays. Vibrating sample magnetometer and physical property measurement system were used to measure their magnetic and giant magnetoresistance （GMR） properties. The effect of sub-layer thickness on the magnetic and GMR properties was investigated. The results indicate that magnetic properties of electmdeposited nanowires are not affected obviously by Cu layer thickness, while magnetic layers （Ni-Fe and Co layers） have significant influence. In addition, GMR ratio presents an oscillatory behavior as Cu layer thickness changes. The magnetic and GMR properties of the multilayered nanowire arrays are optimum at room temperature for the material structure of Ni-Fe （25 nm）/Cu （15 nm）/Co （25 nm）/Cu （15 nm） with 30 deposition cycles.
