The effects of relative humidity (RH) on a printed circuit board finished with electroless nickel immersion gold (PCB-ENIG) under an adsorbed thin electrolyte layer (ATEL) were investigated in situ via the measurement...The effects of relative humidity (RH) on a printed circuit board finished with electroless nickel immersion gold (PCB-ENIG) under an adsorbed thin electrolyte layer (ATEL) were investigated in situ via the measurement of cathodic polarization curves, electrochemical impedance spectroscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray photoelectron spectroscopy to clearly elaborate the corrosion behavior of PCB-ENIG in the atmospheric environment. Results indicated that the cathodic process of PCB-ENIG under ATEL was dominated by the reduction of dissolved oxygen, corrosion products, and H2O. The cathodic current density of PCB-ENIG increased progressively with increasing RH. Moreover, its cathodic current density in the solution was greater than that under ATEL. This result demonstrated that the diffusion process was not the controlling step during the limiting reduction of cathodic oxygen. When the polarization potentials were located in a more negative region, the cathodic polarization current density gradually decreased under 75% and 85% RH. Notably, the anodic process became the controlling step in the extremely thin liquid film during the remainder of the experiment.展开更多
The process parameters were optimized for the electrodeposition of cobalt from cobalt chloride solution in the membrane electrolytic reactor. Effects of parameters such as catholyte composition, current density and t...The process parameters were optimized for the electrodeposition of cobalt from cobalt chloride solution in the membrane electrolytic reactor. Effects of parameters such as catholyte composition, current density and temperature on the current efficiency, specific power consumption and quality of deposition were studied. The catholyte was a mixed solution of cobalt chloride, the initial middle electrolyte consisted of diluted hydrochloric acid, and the anolyte was sulfuric acid. An anion exchange membrane separated the catholyte from the middle electrolyte, and a cation exchange membrane separated the anolyte from the middle electrolyte. The results showed that a maximum current efficiency of 97.5% was attained under the optimum experimental condition of an catholyte composition of 80 g/L Co^2＋, 20 g/L H3BO3, 3 g/L NaF and pH of 4, at a cathode current density of 250 A/m2 and a temperature of 50 ℃ HCl could be produced in the middle compartment electrochemically up to 0.45 mol/L.展开更多
LiCo0.8M0.2O2 （M=Ni,Zr） films were fabricated by radio frequency sputtering deposition combined with conventional annealing methods. The strtuctures of the films were characterized with X-ray diffraction （XRD）, Ra...LiCo0.8M0.2O2 （M=Ni,Zr） films were fabricated by radio frequency sputtering deposition combined with conventional annealing methods. The strtuctures of the films were characterized with X-ray diffraction （XRD）, Raman spectroscopy and scarming electron microscopy （SEM） techniques. It was shown that the 700 ℃- annealed LiCo0.8M0.2O2 has an α-NaFeO2 like layered structure. All-solid-state thin-film batteries （TFBs） were fabrieated with these films as the cathode and their eleetroctemical performances were evaluated. It was found that doping of electrochemically active Ni and inactive Zr has different effects on the structural and elcctrochemical properties of the LiCoO2 cathode films. Ni doping increases the discharge capacity of the film while Zr doping improves its cycling stability.展开更多
Diamond like carbon thin film is successfully deposited on silicon, titanium and stainless steel substrate at low temperature in a filtered vacuum arc deposition system. Arc discharges are established on a graphite ...Diamond like carbon thin film is successfully deposited on silicon, titanium and stainless steel substrate at low temperature in a filtered vacuum arc deposition system. Arc discharges are established on a graphite cathode in the system with a toroidal macroparticle filter. A cathode activating magnetic field and a filtered magnetic field to collimate the plasma beam are applied. Ion current convected by the plasma beam is measured with a negatively biased probe. It is shown that the magnetic field of the coils located on the plasma duct has a strong influence on cathode spot behavior. Orthogonally the designed experiments are carried out to optimize the deposition parameters of arc stability. Finally, the diamond like carbon thin films are studied by scanning electron microscope (SEM) and Raman spectrum.展开更多
Diamond like carbon (DLC) films was grown successfully on silicon, titanium and high speed steel (HSS) substrate at low temperature in a filtered vacuum arc deposition system. Arc discharges were established on a gra...Diamond like carbon (DLC) films was grown successfully on silicon, titanium and high speed steel (HSS) substrate at low temperature in a filtered vacuum arc deposition system. Arc discharges were established on a graphite cathode in this home built system with a toridal macroparticles filter. Ion current convected by the plasma beam was measured with a negatively biased probe. It was shown that the magnetic field of the coils located on the plasma duct has a strong influence on ion current. Scanning electron microscope (SEM), atomic force microscope (AFM) and Raman spectrum are used to study the DLC films. Tribological behaviors of the deposited film are also studied.展开更多
A phosphate solution free of chromate, fluoride and nitrite was prepared and an environment-friendly film was obtained on AZ31 magnesium alloy surface via the chemical deposition method. The morphology, composition, p...A phosphate solution free of chromate, fluoride and nitrite was prepared and an environment-friendly film was obtained on AZ31 magnesium alloy surface via the chemical deposition method. The morphology, composition, phase structure and its corrosion resistance were studied. The effects of film-forming temperature and free acid on corrosion resistance, microstructure and electrochemical behavior of the film were discussed. The results indicate that the corrosion resistance of AZ31 with the phosphate film was better than blank AZ31 substrate, which was most attributed to the great inhibitive action on the anodic dissolution and cathodic hydrogen evolution of the film.展开更多
文摘分别以三聚氰胺和戊二醛改性壳聚糖,三价铬离子改性羧甲基纤维素钠(CMC)制备了mCMC/Mel-CS双极膜.阴膜层经三聚氰胺改性后,离子交换容量增大、膜的交流阻抗降低.J-E工作曲线的测试结果表明,以该双极膜装配的电解槽工作电压较低.在40mA·cm-2的工作电流密度下,电解槽工作电压低于4.3 V.
基金Project(51271032)supported by the National Natural Science Foundation of ChinaProject(2014CB643300)supported by the National Basic Research Program of ChinaProject supported by the National Environmental Corrosion Platform,China
文摘The effects of relative humidity (RH) on a printed circuit board finished with electroless nickel immersion gold (PCB-ENIG) under an adsorbed thin electrolyte layer (ATEL) were investigated in situ via the measurement of cathodic polarization curves, electrochemical impedance spectroscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray photoelectron spectroscopy to clearly elaborate the corrosion behavior of PCB-ENIG in the atmospheric environment. Results indicated that the cathodic process of PCB-ENIG under ATEL was dominated by the reduction of dissolved oxygen, corrosion products, and H2O. The cathodic current density of PCB-ENIG increased progressively with increasing RH. Moreover, its cathodic current density in the solution was greater than that under ATEL. This result demonstrated that the diffusion process was not the controlling step during the limiting reduction of cathodic oxygen. When the polarization potentials were located in a more negative region, the cathodic polarization current density gradually decreased under 75% and 85% RH. Notably, the anodic process became the controlling step in the extremely thin liquid film during the remainder of the experiment.
基金Project(2015016)supported by the Young Scholars Science Foundation of Lanzhou Jiaotong University,ChinaProject(2015BAE04B01)supported by the National Science-technology Support Program of ChinaProject(21466019)supported by the National Natural Science Foundation of China
文摘The process parameters were optimized for the electrodeposition of cobalt from cobalt chloride solution in the membrane electrolytic reactor. Effects of parameters such as catholyte composition, current density and temperature on the current efficiency, specific power consumption and quality of deposition were studied. The catholyte was a mixed solution of cobalt chloride, the initial middle electrolyte consisted of diluted hydrochloric acid, and the anolyte was sulfuric acid. An anion exchange membrane separated the catholyte from the middle electrolyte, and a cation exchange membrane separated the anolyte from the middle electrolyte. The results showed that a maximum current efficiency of 97.5% was attained under the optimum experimental condition of an catholyte composition of 80 g/L Co^2＋, 20 g/L H3BO3, 3 g/L NaF and pH of 4, at a cathode current density of 250 A/m2 and a temperature of 50 ℃ HCl could be produced in the middle compartment electrochemically up to 0.45 mol/L.
基金supported Science Foundation of China by the National Natural(No.20203006).
文摘LiCo0.8M0.2O2 （M=Ni,Zr） films were fabricated by radio frequency sputtering deposition combined with conventional annealing methods. The strtuctures of the films were characterized with X-ray diffraction （XRD）, Raman spectroscopy and scarming electron microscopy （SEM） techniques. It was shown that the 700 ℃- annealed LiCo0.8M0.2O2 has an α-NaFeO2 like layered structure. All-solid-state thin-film batteries （TFBs） were fabrieated with these films as the cathode and their eleetroctemical performances were evaluated. It was found that doping of electrochemically active Ni and inactive Zr has different effects on the structural and elcctrochemical properties of the LiCoO2 cathode films. Ni doping increases the discharge capacity of the film while Zr doping improves its cycling stability.
文摘Diamond like carbon thin film is successfully deposited on silicon, titanium and stainless steel substrate at low temperature in a filtered vacuum arc deposition system. Arc discharges are established on a graphite cathode in the system with a toroidal macroparticle filter. A cathode activating magnetic field and a filtered magnetic field to collimate the plasma beam are applied. Ion current convected by the plasma beam is measured with a negatively biased probe. It is shown that the magnetic field of the coils located on the plasma duct has a strong influence on cathode spot behavior. Orthogonally the designed experiments are carried out to optimize the deposition parameters of arc stability. Finally, the diamond like carbon thin films are studied by scanning electron microscope (SEM) and Raman spectrum.
文摘Diamond like carbon (DLC) films was grown successfully on silicon, titanium and high speed steel (HSS) substrate at low temperature in a filtered vacuum arc deposition system. Arc discharges were established on a graphite cathode in this home built system with a toridal macroparticles filter. Ion current convected by the plasma beam was measured with a negatively biased probe. It was shown that the magnetic field of the coils located on the plasma duct has a strong influence on ion current. Scanning electron microscope (SEM), atomic force microscope (AFM) and Raman spectrum are used to study the DLC films. Tribological behaviors of the deposited film are also studied.
基金Projects (2011CL08, 2011CL01) supported by Open Fund of Material Corrosion and Protection Key Laboratory of Sichuan Province, ChinaProject (2011RC02) supported by Talent Introduction Funds of Sichuan University of ScienceProject (12ZA261) supported by Key Project of Education Department of Sichuan Province, China
文摘A phosphate solution free of chromate, fluoride and nitrite was prepared and an environment-friendly film was obtained on AZ31 magnesium alloy surface via the chemical deposition method. The morphology, composition, phase structure and its corrosion resistance were studied. The effects of film-forming temperature and free acid on corrosion resistance, microstructure and electrochemical behavior of the film were discussed. The results indicate that the corrosion resistance of AZ31 with the phosphate film was better than blank AZ31 substrate, which was most attributed to the great inhibitive action on the anodic dissolution and cathodic hydrogen evolution of the film.
