“如果可以重来，就是金山银山我都不会动心”——贪官陶超的狱中感叹

陶超，江苏省盐城市交通局原局长，因犯受贿罪、巨额财产来源不明罪，2002年9月被盐城市中级法院判处有期徒刑十七年，并处没收个人财产15万元。

Microstructure and Oxidation Behavior of ZrB_(2)-SiC Ceramics Fabricated by Tape Casting and Reactive Melt Infiltration

ZrB_(2)-based ceramics typically necessitate high temperature and pressure for sintering,whereas ZrB_(2)-SiC ceramics can be fabricated at 1500℃using the process of reactive melt infiltration with Si.In comparison to the conventional preparation method,reactive synthesis allows for the more facile production of ultra-high temperature ceramics with fine particle size and homogeneous composition.In this work,ZrSi_(2),B4C,and C were used as raw materials to prepare ZrB_(2)-SiC via combination of tape casting and reactive melt infiltration herein referred to as ZBC ceramics.Control sample of ZrB_(2)-SiC was also prepared using ZrB_(2) and SiC as raw materials through an identical process designated as ZS ceramics.Microscopic analysis of both ceramic groups revealed smaller and more uniformly distributed particles of the ZrB_(2) phase in ZBC ceramics compared to the larger particles in ZS ceramics.Both sets of ceramics underwent cyclic oxidation testing in the air at 1600℃for a cumulative duration of 5 cycles,each cycle lasting 2 h.Analysis of the oxidation behavior showed that both ZBC ceramics and ZS ceramics developed a glassy SiO_(2)-ZrO_(2) oxide layer on their surfaces during the oxidation.This layer severed as a barrier against oxygen.In ZBC ceramics,ZrO_(2) is finely distributed in SiO_(2),whereas in ZS ceramics,larger ZrO_(2) particles coexist with glassy SiO_(2).The surface oxide layer of ZBC ceramics maintains a dense structure because the well-dispersed ZrO_(2) increases the viscosity of glassy SiO_(2),preventing its crystallization during the cooling.Conversely,some SiO_(2) in the oxide layer of ZS ceramics may crystallize and form a eutectic with ZrO_(2),leading to the formation of ZrSiO_(4).This leads to cracking of the oxide layer due to differences in thermal expansion coefficients,weakening its barrier effect.An analysis of the oxidation resistance shows that ZBC ceramics exhibit less increase in oxide layer thickness and mass compared to ZS ceramics,suggesting superior oxidation resistance of ZBC ceramics.

Reactive HVOF sprayed TiN-matrix composite coating and its corrosion and wear resistance properties

TiN-matrix composite coating was prepared on 45# steel by reactive high-velocity oxy-fuel （HVOF） spraying. Its microstructure, phase composition, micro-hardness, corrosion resistance in 3.5% NaC1 solution and wear resistance were analyzed. The results suggest that the TiN-matrix composite coating is well bonded with the substrate. The micro-hardness measured decreases with the increase of applied test loads. And the micro-hardness of the coating under heavy loads is relatively high. The TiN-matrix composite coating exhibits an excellent corrosion resistance in 3.5% NaC1 solution. The corrosion potential of coating is positive and the passivation zone is broad, which indicates that the TiN-matrix composite coating is stable in the electrolyte and provides excellent protection to the substrate. The wear coefficient of the coating under all loads maintains at 0.49-0.50. The wear mechanism of the coating is revealed to be three-body abrasive wear. Yet the failure forms of TiN-matrix composite coating under different loads have an obvious difference. The failure form of coating under light loads is particle spallation due to the stress concentration while that of coating under heavy loads is crackin~ between inter-lamellae.

Progress on Porous Ceramic Membrane Reactors for Heterogeneous Catalysis over Ultrafine and Nano-sized Catalysts

Heterogeneous catalysts with ultrafine or nano particle size have currently attracted considerable attentions in the chemical and petrochemical production processes, but their large-scale applications remain challenging because of difficulties associated with their efficient separation from the reaction slurry. A porous ceramic membrane reactor has emerged as a promising method to solve the problem concerning catalysts separation in situ from the reaction mixture and make the production process continuous in heterogeneous catalysis. This article presents a review of the present progress on porous ceramic membrane reactors for heterogeneous catalysis, which covers classification of configurations of porous ceramic membrane reactor, major considerations and some important industrial applications. A special emphasis is paid to major considerations in term of application-oriented ceramic membrane design, optimization of ceramic membrane reactor performance and membrane fouling mechanism. Finally, brief concluding remarks on porous ceramic membrane reactors are given and possible future research interests are also outlined.

Effect of Ultrasound on the Treatment of Emulsification Wastewater by Ceramic Membranes

Ultrasonic field was applied in the treatment of oil emulsification wastewater by ZrO2 ceramic mem-brane. The permeate flux, rejection ratio in the filtration process and recovery ratio of flux in the membrane cleaning process were measured. Great improvement in the permeate flux and rejection ratio have been observed for the membrane process enhanced by the ultrasonic field. The permeate flux of water through the membrane was about 210L.m^-2.h^-1 and the oil rejection ratio was over 99.9% under the optimal ultrasonic treatment conditions, which were 8W of ultrasonic power, 7cm of ultrasonic probe length introduced into the membrane channel and the same ultrasonic radiation direction as the wastewater flow. The resistance of the membrane process was compared between the cases with and without ultrasound, and the total resistance was reduced 68% by the use of ultrasound, Four methods including water cleaning, water cleaning under sonication, chemical cleaning and chemical cleaning under sonication were used to recover membrane flux. It was found that the flux recovery ratio increased with the increase of ultrasonic cleaning power. In addition, the use of chemical agents combining with ultrasonic irradiation showed a synergistic effect, which resulted in the highest cleaning efficiency and the shorter cleaning time.

Effect of nano-size nickel particles on wear resistance and high temperature oxidation resistance of ultrafine ceramic coating

In order to improve the wear resistance and high temperature oxidation resistance of titanium and titanium alloy, the high temperature ultra fine ceramic coating containing nano-size nickel particles was prepared by flow coat method on the surface of industrially pure titanium TB1-0. The effects of nano-size nickel particles on the wear resistance and high temperature oxidation resistance of coating substrate system were investigated through oxidation kinetics experiment and wear resistance test. The morphologies of the specimens were examined by means of optical microscopy, scanning electron microscopy and X-ray diffraction. The results show that the high temperature ultra fine ceramic coating has notable protection effect on industrially pure titanium TB1-0 from oxidation. The oxidation and wear resistance properties of the coating can be effectively improved by adding nano-size nickel particles. The oxidative mass gain of the specimen decreases from 11.33 mg·cm-2 to 5.25 mg·cm-2 and the friction coefficient decreases from 1.1 to 0.6 by adding nano-size nickel particles, and the coating containing 10% （mass fraction） nano-size nickel shows the optimum properties.

Investigation of compaction and sintering behavior of SiC powder after ultra-fine treatment

Silicon carbide ceramics were prepared with SiC powder treated by the fluidized bed opposed jet mill as raw materials, and the effects of the ultra-fine treatment mechanism on the compaction and sintering behavior of SiC ceramics were investigated. The results showed that the compacts had higher density and microstructure homogeneity when the sintering temperature of the compact was decreased; and that the surface microstructure, densification and mechanical properties of the sintered body could be ameliorated obviously.

New High Tc-Value Investigated in Superconducting System YBa2（C u3）1-xA gxO6.5x＋δ

A ceramic superconductor compound with composition YBa2（C u3）1-xA gxO6.5x＋δhas been prepared experimentally by solid state reaction from principal roots of high purity materials like Y203, BaO, CuO and Ag20. The study was concentrated on the effect of partial substitution of Ag with respect to Cu atoms by the ratios （x = 0, 1, 0.2, 0.3, 0.4 and 0.5） through different analysis and measurements. X-ray diffraction （XRD）, Scanning Electron Microscope （SEM） and Resistivity measurement is play an important role to show the improvement on high superconducting phase. It was found that the best substituted value of （x = 0.5） investigated a favor value of Tc equal nearly to （123 K）, due to more excess of Ag atoms in the structure. X-ray diffraction showed an orthorhombic structure related to high-To phase with high stability through diminishing some peaks related to low temperature superconducting phase, that was related to presence of multiphase derivative from YBCO-phase. SEM pictures give us more details on the surface morphology, grain and grain boundaries, it gives an indication on successful of sintering process, the last one is very important in forming superconducting phase.

Dispersion of ultrafine SiC particles in molten Al-12Si alloy

The bulk A1-12 Si eutectic composites were fabricated through a conventional liquid metal casting route, especially with the help of ultrafine ceramic powders made by self-propagating high-temperature synthesis （SHS） process. The SHS powders were fabricated by the chemical reaction between micro-sized SiC and A1 particles at very high combustion temperatures, producing the coarse A1 particles （several tens of microns） containing ultrafine SiC ceramic particles. Microstructural observation revealed that the addition of ultrafine SiC particles has a crumbling tendency of Si eutectic phase. It is suggested that the casting method combined with SHS process is promising for fabricating the Al-based MMC with ultrafine ceramic particles.

Fabrication and plasma arc thermal shock resistance of HfB_2-based ultra high temperature ceramics

Two hafnium diboride based ceramic matrix composites containing 20% （volume fraction） SiC particle and with or without AIN as sintering additives were fabri,aated by hot-pressed sintering. The mechanical properties and microstructures of these two composites were tested and the thermal shock resistances were evaluated by plasma arc heater. The results indicate that the composite with A1N as sintering additive has a denser and finer microstructure than composite without sintering additive, and the mechanical properties, thermal shock resistance of the composite with A1N as sintering additive are also higher than those of the composite without A1N. Microstructure analysis on the cross-section of two composites after thermal shock tests indicates that a compact oxidation scale contains HfO2 and Al2O3 liquid phase is found on the surface of composite with A1N, which could fill the voids and cracks of surface and improve the thermal shock resistance of composite.

An automated AFM for nanoindentation and force related measurements

A fully automated atomic force microscope(AFM)is presented.The mechanical motion of the AFM stage was controlled by three steppers.The fine motion of the AFM was controlled by an MCL one-axis piezo plate.A32.768kHz crystal tuning fork(TF)was used as the transducer with a probe attached.An acoustic sensor was used to measure the interactions between the probe and the sample.An SR850lock-in amplifier was used to monitor the TF signals.An additional lock-in amplifier was used to monitor the acoustic signal.A field programmable gate array(FPGA)board was used to collect the data in automatic mode.The main controller was coded with LabVIEW,which was in charge of Z-axis scan,signal processing and data visualization.A manual mode and an automatic mode were implemented in the controller.Users can switch the two modes at any time during the operation.This AFM system showed several advantages during the test operations.It is simple,flexible and easy to use.

必然因果或自由意志——论《陶渊明》与梁启超后期学术理路

梁启超《陶渊明》和陈寅恪《陶渊明之思想与清谈之关系》之间的对话是近代学术研究中的一段公案。若想在还原对话现场之外,激活讨论深藏的理论面向,则需要恢复特定认识脉络的历史感知。实际上,主导梁启超1920年后学术理路的,是依托欧游中的具体经验产生的对必然因果与自由意志问题的一系列思索。《陶渊明》作为这一思索的延伸,体现了梁启超后期对个体自我价值感的关注、在文献之学与德性之学间不可偏废的立场以及对《新史学》中所倡导的因果律的深刻反思。

Grain oriented growth and properties of ultra-high temperature CaBi_2Nb_2O_9 piezoelectric ceramics

CaBi2Nb2O9 (CBNO) ceramics was prepared at 1050℃ using regular flake-like CBNO powders as the precursor, and synthe-sized by the molten salts synthesis method. The tropism degree and microstructure of the ceramics were analyzed, and the die-lectric, ferroelectric and piezoelectric properties were characterized. Compared with conventional methods, the properties of CBNO ceramics by the new preparation method were found to be better. As the sinter temperature decreases, the grain growth becomes regular with textured features. The polarization process becomes easy to be realized at room temperature. Moreover, the dielectric loss decreases and the piezoelectric constant increases significantly.

Ultra-fast densification of CNTs reinforced alumina based on combustion reaction and quick pressing

An ultra-fast densification method based on high heating rate from the combustion reaction for producing carbon nanotubes （CNTs） reinforced alumina ceramics is reported. The heat generated by combustion reaction is adopted to act as a high temperature source to the sample, which results in a heating rate of 1660℃/min of the sample. Then a great mechanical pressure is applied to the sample when the sample gets the expected temperature. The densification process is finished in several minutes. The results indicate that the densification method is beneficial to protect the CNTs from destruction and creates good interracial combination between the nanotubes and the matrix. With the addition of 1 wt% CNTs, the fracture toughness of the ceramics prepared increases about 50%.