To study the rock breaking method under the free surface induced by disc cutter,the rock breaking simulations were first conducted based on the discrete element method,and the dynamic process of rock breaking under th...To study the rock breaking method under the free surface induced by disc cutter,the rock breaking simulations were first conducted based on the discrete element method,and the dynamic process of rock breaking under the free surface was studied including stressed zone,crush zone,crack initiation and propagation.Then the crack propagation conditions,specific energy,etc.under different free surface distance(S)were also investigated combined with linear cutting experiments.The results show that the rock breaking process under the free surface induced by disc cutter is dominated by tension failure mode.There exists a critical S to promote crack propagation to free surface effectively.And this rock breaking method can improve the rock breaking force and breaking efficiency significantly when proper.展开更多
When the tunneling boring machine(TBM) cutterhead tunnels, the excessive vibration and damage are a severe engineering problem, thereby the anti-vibration design is a key technology in the disc cutter system. The stru...When the tunneling boring machine(TBM) cutterhead tunnels, the excessive vibration and damage are a severe engineering problem, thereby the anti-vibration design is a key technology in the disc cutter system. The structure of disc cutter contains many joint interfaces among cutter ring, cutter body, bearings and cutter shaft. On account of the coupling for dynamic contact and the transfer path among joint interface, mechanical behavior of disc cutter becomes extremely complex under the impact of heavy-duty, which puts forward higher requirements for disc cutter design. A multi-degree-of-freedom coupling dynamic model, which contains a cutter ring, a cutter body, two bearings and cutter shaft, is established, considering the external stochastic excitations, bearing nonlinear contact force, multidirectional mutual coupling vibration, etc. Based on the parameters of an actual project and the strong impact external excitations, the modal properties and dynamic responses are analyzed, as well as the cutter shaft and bearings' loads and load transmission law are obtained. Numerical results indicate the maximum radial and axial cutter ring amplitudes of dynamic responses are 0.568 mm and 0.112 mm; the maximum radial and axial vibration velocities are 41.1 mm/s and 38.9 mm/s; the maximum radial and axial vibration accelerations are 94.7 m/s2 and 58.6 m/s2; the maximum swing angle and angular velocity of cutter ring are 0.007° and 0.0074 rad/s, respectively. Finally, the maximum load of bearing roller is 40.3 k N. The proposed research lays a foundation for structure optimization design of disc cutter and cutter base, as well as model selection, modification and fatigue life of the cutter bearing.展开更多
This paper describes the influence of joint spacing and joint orientation on the penetration rate of a Tunnel Boring Machine （TBM） disc cutter as modeled by the Discrete Element Method （DEM）. The input data for th...This paper describes the influence of joint spacing and joint orientation on the penetration rate of a Tunnel Boring Machine （TBM） disc cutter as modeled by the Discrete Element Method （DEM）. The input data for the siLmulations were obtained from the sandstone along the AIborz tunnel that is currently being excavated in Iran using a 5.2 m diameter open TBM. Three joint spacings, 150, 200, and 300 mm, were modeled together with seven values of joint orientation; 0°, 15°, 30°, 45°, 60°, 75°, and 90°. The results show that the penetration increases when joint orientation increases from 0° to 75°, but it decreases as the joint orientation increases further from 75° to 90°. This is true for each joint spacing. In addition, for a given joint orientation increasing the joint spacing causes the TBM penetration to decrease. The optimum joint orientation, from the viewpoint of TBM penetration, is about 60-75°.展开更多
基金Project(2013CB035401)supported by the National Basic Research Program of ChinaProject(2012AA041803)supported by the National High-Technology Research and Development Program of China+2 种基金Project(51475478)supported by the National Natural Science Foundation of ChinaProject(2015GK1029)supported by the Science and Technology Project of Strategic Emerging Industry in Hunan Province,ChinaProject(CX2017B048)supported by the Hunan Provincial Innovation Foundation For Postgraduate,China
文摘To study the rock breaking method under the free surface induced by disc cutter,the rock breaking simulations were first conducted based on the discrete element method,and the dynamic process of rock breaking under the free surface was studied including stressed zone,crush zone,crack initiation and propagation.Then the crack propagation conditions,specific energy,etc.under different free surface distance(S)were also investigated combined with linear cutting experiments.The results show that the rock breaking process under the free surface induced by disc cutter is dominated by tension failure mode.There exists a critical S to promote crack propagation to free surface effectively.And this rock breaking method can improve the rock breaking force and breaking efficiency significantly when proper.
基金Project(51375001) supported by the National Natural Science Foundation of ChinaProject(2013CB035400) supported by the National Basic Research Program of China
文摘When the tunneling boring machine(TBM) cutterhead tunnels, the excessive vibration and damage are a severe engineering problem, thereby the anti-vibration design is a key technology in the disc cutter system. The structure of disc cutter contains many joint interfaces among cutter ring, cutter body, bearings and cutter shaft. On account of the coupling for dynamic contact and the transfer path among joint interface, mechanical behavior of disc cutter becomes extremely complex under the impact of heavy-duty, which puts forward higher requirements for disc cutter design. A multi-degree-of-freedom coupling dynamic model, which contains a cutter ring, a cutter body, two bearings and cutter shaft, is established, considering the external stochastic excitations, bearing nonlinear contact force, multidirectional mutual coupling vibration, etc. Based on the parameters of an actual project and the strong impact external excitations, the modal properties and dynamic responses are analyzed, as well as the cutter shaft and bearings' loads and load transmission law are obtained. Numerical results indicate the maximum radial and axial cutter ring amplitudes of dynamic responses are 0.568 mm and 0.112 mm; the maximum radial and axial vibration velocities are 41.1 mm/s and 38.9 mm/s; the maximum radial and axial vibration accelerations are 94.7 m/s2 and 58.6 m/s2; the maximum swing angle and angular velocity of cutter ring are 0.007° and 0.0074 rad/s, respectively. Finally, the maximum load of bearing roller is 40.3 k N. The proposed research lays a foundation for structure optimization design of disc cutter and cutter base, as well as model selection, modification and fatigue life of the cutter bearing.
文摘This paper describes the influence of joint spacing and joint orientation on the penetration rate of a Tunnel Boring Machine （TBM） disc cutter as modeled by the Discrete Element Method （DEM）. The input data for the siLmulations were obtained from the sandstone along the AIborz tunnel that is currently being excavated in Iran using a 5.2 m diameter open TBM. Three joint spacings, 150, 200, and 300 mm, were modeled together with seven values of joint orientation; 0°, 15°, 30°, 45°, 60°, 75°, and 90°. The results show that the penetration increases when joint orientation increases from 0° to 75°, but it decreases as the joint orientation increases further from 75° to 90°. This is true for each joint spacing. In addition, for a given joint orientation increasing the joint spacing causes the TBM penetration to decrease. The optimum joint orientation, from the viewpoint of TBM penetration, is about 60-75°.
