Al2O3/R141b ＋ Span-80 nanorefrigerant for 0.05 wt.% to 0.4 wt.% is prepared by ultrasonic vibration to investigate the influence of nanoparticle concentrations on flow boiling heat transfer of Al2O3/R141b ＋ Span-80...Al2O3/R141b ＋ Span-80 nanorefrigerant for 0.05 wt.% to 0.4 wt.% is prepared by ultrasonic vibration to investigate the influence of nanoparticle concentrations on flow boiling heat transfer of Al2O3/R141b ＋ Span-80 in micro heat exchanger by direct metal laser sintering. Experimental results show that nanoparticle concentrations have significantly impact on heat transfer coefficients by homogeneity test of variances according to mathematical statistics. The heat transfer performance of Al2O3/R141b ＋ Span-80 nanorefrigerant is enhanced after adding nanoparticles in the pure refrigerant R141b. The heat transfer coefficients of 0.05 wt.%, 0.1 wt.%, 0.2 wt.%, 0.3 wt.% and 0.4 wt.% Al2O3/R141 b ＋ Span-80 nanorefrigerant respectively increase by 55.0% 72.0%, 53.0% 42.3% and 39.9% compared with the pure refrigerant R141b. The particle fluxes from viscosity gradient, non-uniform shear rate and Brownian motion cause particles to migrate in fluid especially in the process of flow boiling. This migration motion enhances heat transfer between nanoparticles and fluid. Therefore, the heat transfer performance of nanofluid is enhanced. It is important to note that the heat transfer coefficients nonlinearly increase with nanoparticle concentrations increasing. The heat transfer coefficients reach its maximum value at the mass concentration of 0.1% and then it decreases slightly. There exists an optimal mass concentration corresponding to the best heat transfer enhancement. The reason for the above phenomenon is attributed to nanoparticles deposition on the minichannel wall by Scanning Electron Microscopy observation. The channel surface wettability increases during the flow boiling experiment in the mass concentration range from 0.2 wt.% to 0.4 wt.%. The channel surface with wettability increasing needs more energy to produce a bubble. Therefore, the heat transfer coefficients decrease with nanopartide concentrations in the range from 0.2 wt.% to 0.4 wt.%. In addition, a new correlation has been proposed by fitting the experimental data considering the influence of mass concentrations on the heat trans- fer performance. The new correlation can effectively predict the heat transfer coefficient.展开更多
Hot compression tests of 2050 Al-Li alloy were performed in the deformation temperature range of 340-500°C and strain rate range of 0.001-10 s-1 to investigate the hot deformation behavior of the alloy.The effect...Hot compression tests of 2050 Al-Li alloy were performed in the deformation temperature range of 340-500°C and strain rate range of 0.001-10 s-1 to investigate the hot deformation behavior of the alloy.The effects of friction and temperature difference on flow stress were analyzed and the flow curves were corrected.Based on the dynamic material model,processing map at a strain of 0.5 was established.The grain structure of the compressed samples was observed using optical microscopy.The results show that friction and temperature variation during the hot compression have significant influences on flow stress.The optimum processing domains are in the temperature range from 370 to 430°C with the strain rate range from 0.01 to 0.001 s-1,and in the temperature range from 440 to 500°C with the strain rate range from 0.3 to 0.01 s-1;the flow instable region is located at high strain rates(3-10 s-1)in the entire temperature range.Dynamic recovery(DRV)and dynamic recrystallization(DRX)are the main deformation mechanisms of the 2050 alloy in the stable domains,whereas the alloy exhibits flow localization in the instable region.展开更多
The mechanism of the zonal disintegration phenomenon(ZDP) was realized based on the analysis of the stressedstrained state of the rock mass in the vicinity of the maximum stress zone, which resides in the creep instab...The mechanism of the zonal disintegration phenomenon(ZDP) was realized based on the analysis of the stressedstrained state of the rock mass in the vicinity of the maximum stress zone, which resides in the creep instability failure of rock mass due to the development of a plastic zone and transfer of the maximum stress zone within the rock mass.Some characteristic parameters of the ZDP are discussed theoretically.In first instance, the analytical critical depth condition for the occurrence of ZDP was obtained, which depends on the characteristics and stress concentration coefficient of the rock mass.Secondly, based on creep theory, the expression of the outer radius of the undisturbed zones in the deep rock mass was obtained with the use of an improved Burgers rheological model, which indicated that the radius depends on the characteristics of the rock mass and the depth of excavation and increases quasi-linearly with the rise of creep compliance of the rock mass.Finally, the formula for the distance of the most remote fissured zone away from the working periphery was derived, which increases logarithmically with the increase in the ratio of the in-situ stress and ultimate strength of rock mass.The distances between fissured zones are discussed in qualitative terms.展开更多
基金Supported by the National Natural Science Foundation of China[21276090]
文摘Al2O3/R141b ＋ Span-80 nanorefrigerant for 0.05 wt.% to 0.4 wt.% is prepared by ultrasonic vibration to investigate the influence of nanoparticle concentrations on flow boiling heat transfer of Al2O3/R141b ＋ Span-80 in micro heat exchanger by direct metal laser sintering. Experimental results show that nanoparticle concentrations have significantly impact on heat transfer coefficients by homogeneity test of variances according to mathematical statistics. The heat transfer performance of Al2O3/R141b ＋ Span-80 nanorefrigerant is enhanced after adding nanoparticles in the pure refrigerant R141b. The heat transfer coefficients of 0.05 wt.%, 0.1 wt.%, 0.2 wt.%, 0.3 wt.% and 0.4 wt.% Al2O3/R141 b ＋ Span-80 nanorefrigerant respectively increase by 55.0% 72.0%, 53.0% 42.3% and 39.9% compared with the pure refrigerant R141b. The particle fluxes from viscosity gradient, non-uniform shear rate and Brownian motion cause particles to migrate in fluid especially in the process of flow boiling. This migration motion enhances heat transfer between nanoparticles and fluid. Therefore, the heat transfer performance of nanofluid is enhanced. It is important to note that the heat transfer coefficients nonlinearly increase with nanoparticle concentrations increasing. The heat transfer coefficients reach its maximum value at the mass concentration of 0.1% and then it decreases slightly. There exists an optimal mass concentration corresponding to the best heat transfer enhancement. The reason for the above phenomenon is attributed to nanoparticles deposition on the minichannel wall by Scanning Electron Microscopy observation. The channel surface wettability increases during the flow boiling experiment in the mass concentration range from 0.2 wt.% to 0.4 wt.%. The channel surface with wettability increasing needs more energy to produce a bubble. Therefore, the heat transfer coefficients decrease with nanopartide concentrations in the range from 0.2 wt.% to 0.4 wt.%. In addition, a new correlation has been proposed by fitting the experimental data considering the influence of mass concentrations on the heat trans- fer performance. The new correlation can effectively predict the heat transfer coefficient.
基金Project(2013JSJJ0001)supported by the Teachers’ Research Fund,Central South University,ChinaProject supported by the Nonferrous Metal Oriented Advanced Structural Materials and Manufacturing Cooperative Innovation Center,China
文摘Hot compression tests of 2050 Al-Li alloy were performed in the deformation temperature range of 340-500°C and strain rate range of 0.001-10 s-1 to investigate the hot deformation behavior of the alloy.The effects of friction and temperature difference on flow stress were analyzed and the flow curves were corrected.Based on the dynamic material model,processing map at a strain of 0.5 was established.The grain structure of the compressed samples was observed using optical microscopy.The results show that friction and temperature variation during the hot compression have significant influences on flow stress.The optimum processing domains are in the temperature range from 370 to 430°C with the strain rate range from 0.01 to 0.001 s-1,and in the temperature range from 440 to 500°C with the strain rate range from 0.3 to 0.01 s-1;the flow instable region is located at high strain rates(3-10 s-1)in the entire temperature range.Dynamic recovery(DRV)and dynamic recrystallization(DRX)are the main deformation mechanisms of the 2050 alloy in the stable domains,whereas the alloy exhibits flow localization in the instable region.
基金Projects 50525825 supported by the National Natural Science Foundation of China2009CB724608 by the National Basic Research Program of China
文摘The mechanism of the zonal disintegration phenomenon(ZDP) was realized based on the analysis of the stressedstrained state of the rock mass in the vicinity of the maximum stress zone, which resides in the creep instability failure of rock mass due to the development of a plastic zone and transfer of the maximum stress zone within the rock mass.Some characteristic parameters of the ZDP are discussed theoretically.In first instance, the analytical critical depth condition for the occurrence of ZDP was obtained, which depends on the characteristics and stress concentration coefficient of the rock mass.Secondly, based on creep theory, the expression of the outer radius of the undisturbed zones in the deep rock mass was obtained with the use of an improved Burgers rheological model, which indicated that the radius depends on the characteristics of the rock mass and the depth of excavation and increases quasi-linearly with the rise of creep compliance of the rock mass.Finally, the formula for the distance of the most remote fissured zone away from the working periphery was derived, which increases logarithmically with the increase in the ratio of the in-situ stress and ultimate strength of rock mass.The distances between fissured zones are discussed in qualitative terms.
