A four-stage monolithic microwave integrated circuits （MMIC） low noise amplifier （LNA） operating from 23 to 36GHz is reported using commercially available 0.15μm PHEMT technology. The LNA is self-biased. To achie...A four-stage monolithic microwave integrated circuits （MMIC） low noise amplifier （LNA） operating from 23 to 36GHz is reported using commercially available 0.15μm PHEMT technology. The LNA is self-biased. To achieve a low noise characteristic, careful optimizations of gate width are performed to reduce gate resistance. Absorption circuits and an elaborate bias structure with a resistor-capacitor network are employed to improve stability. Multiple resonance points and negative feedback technologies are used to widen the bandwidth. Measurements show a noise figure （NF） of less than 2.0dB,and the lowest NF is only 1.6dB at a frequency of 31GHz. In the whole operation band,the LNA has a gain of higher than 26dB,and an input return loss and output return loss of more than 11 and 13dB,respectively. The output power at ldB compression gain of 36GHz is about 14dBm. The chip area is 2.4mm ×1mm.展开更多
In planning and executing marine controlled-source electromagnetic methods, seafloor electromagnetic receivers must overcome the problems of noise, clock drift, and power consumption. To design a receiver that perform...In planning and executing marine controlled-source electromagnetic methods, seafloor electromagnetic receivers must overcome the problems of noise, clock drift, and power consumption. To design a receiver that performs well and overcomes the abovementioned problems, we performed forward modeling of the E-field abnormal response and established the receiver＇s characteristics. We describe the design optimization and the properties of each component, that is, low-noise induction coil sensor, low-noise Ag/AgCI electrode, low-noise chopper amplifier, digital temperature-compensated crystal oscillator module, acoustic telemetry modem, and burn wire system. Finally, we discuss the results of onshore and offshore field tests to show the effectiveness of the developed seafloor electromagnetic receiver and its performance： typical E-field noise of 0.12 nV/m/rt（Hz） at 0.5 Hz, dynamic range higher than 120 dB, clock drift lower than 1 ms/day, and continuous operation of at least 21 days.展开更多
This paper presents a new class of semiconductor integrated sensor which consists of sensitive components and flip flop circuit. The sensors have high sensitivity and digital output. This paper describes the operatin...This paper presents a new class of semiconductor integrated sensor which consists of sensitive components and flip flop circuit. The sensors have high sensitivity and digital output. This paper describes the operating principle and structure of the sensor. And noise effect on characteristics of the sensor is analysed in detail. The modulated effect of the triangular wave voltage is quantified. As an example, an integrated pressure sensor is introduced and the experimental results agree with the theoretical analyses.展开更多
A control problem of a chain of integrator system with measurement noise on feedback sensor is considered. We propose a gain-scaling controller for compensating measurement noise of feedback sensor. Because control sy...A control problem of a chain of integrator system with measurement noise on feedback sensor is considered. We propose a gain-scaling controller for compensating measurement noise of feedback sensor. Because control systems operate via feedback sensor＇s signal, the measurement noise in sensor＇ signal results in performance degradation or even system failure. Therefore, control systems often demand on compensating measurement noise. Our controller is equipped with a compensator and gain-scaling factor in order to reduce the effect of measurement noise on feedback sensor.展开更多
In this paper, a fully integrated CMOS receiver frontend for high-speed short range wireless applications centering at 60GHz millimeter wave （mmW） band is designed and implemented in 90nm CMOS technology. The 60GHz ...In this paper, a fully integrated CMOS receiver frontend for high-speed short range wireless applications centering at 60GHz millimeter wave （mmW） band is designed and implemented in 90nm CMOS technology. The 60GHz receiver is designed based on the super-heterodyne architecture consisting of a low noise amplifier （LNA） with inter-stage peaking technique, a single- balanced RF mixer, an IF amplifier, and a double-balanced I/Q down-conversion IF mixer. The proposed 60GHz receiver frontend derives from the sliding-IF structure and is designed with 7GHz ultra-wide bandwidth around 60GHz, supporting four 2.16GHz receiving channels from IEEE 802.1lad standard for next generation high speed Wi- Fi applications. Measured results show that the entire receiver achieves a peak gain of 12dB and an input 1-dB compression point of -14.SdBm, with a noise figure of lower than 7dB, while consumes a total DC current of only 60mA from a 1.2V voltage supply.展开更多
To improve the working and living environment of submarine crews, an integrated system of CO2 removal and O2 regeneration was designed to work under experimental conditions for 50 people in a submarine cabin during pr...To improve the working and living environment of submarine crews, an integrated system of CO2 removal and O2 regeneration was designed to work under experimental conditions for 50 people in a submarine cabin during prolonged voyages. The integrated system comprises a solid amine water desorption （SAWD） unit for CO2 collection and concentration, a Sabatier reactor for CO2 reduction and a solid polymer electrolyte （SPE） unit for O2 regeneration by electrolysis. The performances of the SAWD-Sabatier-SPE integrated system were investigated. The experimental results from the SAWD unit showed that the average CO2 concentration in the CO2 storage tank was more than 96% and the outlet CO2 concentration was nearly zero in the first 45 min, and less than 1/10 of inlet CO2 after 60 min when input CO2 was 0.5% （1000 L）. About 950 L of CO2 was recovered with a recovery rate of 92%-97%. The output CO2 concentration was less than 0.2%, which showed that the adsorption-desorption performance of this unit was excellent. In the CO2 reduction unit we investigated mainly the start-up and reaction performance of the Sabatier reactor. The start-up time of the Sabatier reactor was 6, 8 and 10 rain when the start-up temperature was 187.3, 179.5 and 168 ℃, respectively. The product water was colorless, transparent, and had a pH of 6.9-7.5, and an electrical conductivity of 80μs/cm. The sum of the concentration of metal ions （Ru^3＋, Al^3＋, Pb^2＋） was 0.028% and that of nonmetal ions （Cl^-, SO4^2-） was 0.05%. In the O2 regeneration unit, the O2 generation rate was 0.48 m^3/d and the quantity was 2400 L, sufficient to meet the submariners＇ basic oxygen demands. These results may be useful as a basis for establishing CO2-1evel limits and O2 regeneration systems in submarines or similar enclosed compartments during prolonged voyages.展开更多
In the present paper,the attention is focused on the characteristics of lightweight materials collection in the duct using acoustic resonance phenomena.The acoustic resonance was excited by using a controlled speaker ...In the present paper,the attention is focused on the characteristics of lightweight materials collection in the duct using acoustic resonance phenomena.The acoustic resonance was excited by using a controlled speaker at the middle of a test duct.We measured the sound pressure level,frequency response characteristics,acoustic damping ratio,mode shape,and lightweight materials response to acoustic resonance excited by a speaker.As a result,the acoustic damping ratio decreased as the mode number of acoustic resonance increased.The tissue strips and the lightweight materials were collected at the node of acoustic pressure when the acoustic resonance was excited.It was made clear that it is possible to control lightweight materials using acoustic resonance excited by a speaker.展开更多
A wearable and high-precision sensor for sound signal acquisition and recognition was fabricated from thin films of specially designed graphene woven fabrics （GWFs）. Upon being stretched, a high density of random cr...A wearable and high-precision sensor for sound signal acquisition and recognition was fabricated from thin films of specially designed graphene woven fabrics （GWFs）. Upon being stretched, a high density of random cracks appears in the network, which decreases the current pathways, thereby increasing the resistance. Therefore, the film could act as a strain sensor on the human throat in order to measure one＇s speech through muscle movement, regardless of whether or not a sound is produced. The ultra-high sensitivity allows for the realization of rapid and low-frequency speech sampling by extracting the signature characteristics of sound waves. In this study, representative signals of 26 English letters, typical Chinese characters and tones, and even phrases and sentences were tested, revealing obvious and characteristic changes in resistance. Furthermore, resistance changes of the graphene sensor responded perfectly with pre-recorded sounds. By combining artificial intelligence with digital signal processing, we expect that, in the future, this graphene sensor will be able to successfully negotiate complex acoustic systems and large quantities of audio data.展开更多
The suspension of electrodynamic loudspeakers includes a surround of the cone and a spider, and it is characterized by the mechanic stiffness in the lumped-parameter model. By solving the nonlinear differential equati...The suspension of electrodynamic loudspeakers includes a surround of the cone and a spider, and it is characterized by the mechanic stiffness in the lumped-parameter model. By solving the nonlinear differential equation of motion which considers the nonlinearity of suspension at low frequencies numerically and measuring different kinds of surrounds and spiders, the nonlinear behavior of suspension is theoretically and experimentally studied. Since the nonlinear stiffness of spiders and surrounds can be measured and fitted respectively before assembled into loudspeakers, which spider works best with which surround is studied. The performance of loudspeakers such as harmonic distortion based on the nonlinear parameters can be predicted.展开更多
文摘A four-stage monolithic microwave integrated circuits （MMIC） low noise amplifier （LNA） operating from 23 to 36GHz is reported using commercially available 0.15μm PHEMT technology. The LNA is self-biased. To achieve a low noise characteristic, careful optimizations of gate width are performed to reduce gate resistance. Absorption circuits and an elaborate bias structure with a resistor-capacitor network are employed to improve stability. Multiple resonance points and negative feedback technologies are used to widen the bandwidth. Measurements show a noise figure （NF） of less than 2.0dB,and the lowest NF is only 1.6dB at a frequency of 31GHz. In the whole operation band,the LNA has a gain of higher than 26dB,and an input return loss and output return loss of more than 11 and 13dB,respectively. The output power at ldB compression gain of 36GHz is about 14dBm. The chip area is 2.4mm ×1mm.
基金sponsored by the 863 Program(No.2009AA09A2012012AA09A201)+1 种基金China Geological Survey Project(No.201100307)the Fundamental Research Funds of the Ministry of Education for the Central Universities(No.2652011249)
文摘In planning and executing marine controlled-source electromagnetic methods, seafloor electromagnetic receivers must overcome the problems of noise, clock drift, and power consumption. To design a receiver that performs well and overcomes the abovementioned problems, we performed forward modeling of the E-field abnormal response and established the receiver＇s characteristics. We describe the design optimization and the properties of each component, that is, low-noise induction coil sensor, low-noise Ag/AgCI electrode, low-noise chopper amplifier, digital temperature-compensated crystal oscillator module, acoustic telemetry modem, and burn wire system. Finally, we discuss the results of onshore and offshore field tests to show the effectiveness of the developed seafloor electromagnetic receiver and its performance： typical E-field noise of 0.12 nV/m/rt（Hz） at 0.5 Hz, dynamic range higher than 120 dB, clock drift lower than 1 ms/day, and continuous operation of at least 21 days.
文摘This paper presents a new class of semiconductor integrated sensor which consists of sensitive components and flip flop circuit. The sensors have high sensitivity and digital output. This paper describes the operating principle and structure of the sensor. And noise effect on characteristics of the sensor is analysed in detail. The modulated effect of the triangular wave voltage is quantified. As an example, an integrated pressure sensor is introduced and the experimental results agree with the theoretical analyses.
基金supported by Basic Science Research Program through the National Research Foundation of Korea(NRF)funded by the Ministry of Education,Science and Technology(2010-0007325)
文摘A control problem of a chain of integrator system with measurement noise on feedback sensor is considered. We propose a gain-scaling controller for compensating measurement noise of feedback sensor. Because control systems operate via feedback sensor＇s signal, the measurement noise in sensor＇ signal results in performance degradation or even system failure. Therefore, control systems often demand on compensating measurement noise. Our controller is equipped with a compensator and gain-scaling factor in order to reduce the effect of measurement noise on feedback sensor.
基金supported by National 973 Program of China 2010CB327404National 863 Program of China 2011AA010202+2 种基金National Science and Technology Major Project of China 2012ZX03004004National Natural Science Foundation of China under grants 61101001,and 61204026Tsinghua University Initiative Scientific Research Program
文摘In this paper, a fully integrated CMOS receiver frontend for high-speed short range wireless applications centering at 60GHz millimeter wave （mmW） band is designed and implemented in 90nm CMOS technology. The 60GHz receiver is designed based on the super-heterodyne architecture consisting of a low noise amplifier （LNA） with inter-stage peaking technique, a single- balanced RF mixer, an IF amplifier, and a double-balanced I/Q down-conversion IF mixer. The proposed 60GHz receiver frontend derives from the sliding-IF structure and is designed with 7GHz ultra-wide bandwidth around 60GHz, supporting four 2.16GHz receiving channels from IEEE 802.1lad standard for next generation high speed Wi- Fi applications. Measured results show that the entire receiver achieves a peak gain of 12dB and an input 1-dB compression point of -14.SdBm, with a noise figure of lower than 7dB, while consumes a total DC current of only 60mA from a 1.2V voltage supply.
基金supported by the National Natural Science Foundation of China (No. 50908062)the State Key Lab of Urban Water Resource and Environment (No. HIT-QAK200808)the Heilongjiang Natural Science Foundation (No. E2007-04), China
文摘To improve the working and living environment of submarine crews, an integrated system of CO2 removal and O2 regeneration was designed to work under experimental conditions for 50 people in a submarine cabin during prolonged voyages. The integrated system comprises a solid amine water desorption （SAWD） unit for CO2 collection and concentration, a Sabatier reactor for CO2 reduction and a solid polymer electrolyte （SPE） unit for O2 regeneration by electrolysis. The performances of the SAWD-Sabatier-SPE integrated system were investigated. The experimental results from the SAWD unit showed that the average CO2 concentration in the CO2 storage tank was more than 96% and the outlet CO2 concentration was nearly zero in the first 45 min, and less than 1/10 of inlet CO2 after 60 min when input CO2 was 0.5% （1000 L）. About 950 L of CO2 was recovered with a recovery rate of 92%-97%. The output CO2 concentration was less than 0.2%, which showed that the adsorption-desorption performance of this unit was excellent. In the CO2 reduction unit we investigated mainly the start-up and reaction performance of the Sabatier reactor. The start-up time of the Sabatier reactor was 6, 8 and 10 rain when the start-up temperature was 187.3, 179.5 and 168 ℃, respectively. The product water was colorless, transparent, and had a pH of 6.9-7.5, and an electrical conductivity of 80μs/cm. The sum of the concentration of metal ions （Ru^3＋, Al^3＋, Pb^2＋） was 0.028% and that of nonmetal ions （Cl^-, SO4^2-） was 0.05%. In the O2 regeneration unit, the O2 generation rate was 0.48 m^3/d and the quantity was 2400 L, sufficient to meet the submariners＇ basic oxygen demands. These results may be useful as a basis for establishing CO2-1evel limits and O2 regeneration systems in submarines or similar enclosed compartments during prolonged voyages.
基金supported by a research grant from Harada commemorative foundation
文摘In the present paper,the attention is focused on the characteristics of lightweight materials collection in the duct using acoustic resonance phenomena.The acoustic resonance was excited by using a controlled speaker at the middle of a test duct.We measured the sound pressure level,frequency response characteristics,acoustic damping ratio,mode shape,and lightweight materials response to acoustic resonance excited by a speaker.As a result,the acoustic damping ratio decreased as the mode number of acoustic resonance increased.The tissue strips and the lightweight materials were collected at the node of acoustic pressure when the acoustic resonance was excited.It was made clear that it is possible to control lightweight materials using acoustic resonance excited by a speaker.
基金This work was supported by Beijing Science and Technology Program （No. D141100000514001）, National Natural Science Foundation of China （No. 51372133）, and National Program on Key Basic Research Project （Nos. 2011CB013000 and 2014CB932401）
文摘A wearable and high-precision sensor for sound signal acquisition and recognition was fabricated from thin films of specially designed graphene woven fabrics （GWFs）. Upon being stretched, a high density of random cracks appears in the network, which decreases the current pathways, thereby increasing the resistance. Therefore, the film could act as a strain sensor on the human throat in order to measure one＇s speech through muscle movement, regardless of whether or not a sound is produced. The ultra-high sensitivity allows for the realization of rapid and low-frequency speech sampling by extracting the signature characteristics of sound waves. In this study, representative signals of 26 English letters, typical Chinese characters and tones, and even phrases and sentences were tested, revealing obvious and characteristic changes in resistance. Furthermore, resistance changes of the graphene sensor responded perfectly with pre-recorded sounds. By combining artificial intelligence with digital signal processing, we expect that, in the future, this graphene sensor will be able to successfully negotiate complex acoustic systems and large quantities of audio data.
基金supported by the National Natural Science Foundation of China(Grant No. 11274172)
文摘The suspension of electrodynamic loudspeakers includes a surround of the cone and a spider, and it is characterized by the mechanic stiffness in the lumped-parameter model. By solving the nonlinear differential equation of motion which considers the nonlinearity of suspension at low frequencies numerically and measuring different kinds of surrounds and spiders, the nonlinear behavior of suspension is theoretically and experimentally studied. Since the nonlinear stiffness of spiders and surrounds can be measured and fitted respectively before assembled into loudspeakers, which spider works best with which surround is studied. The performance of loudspeakers such as harmonic distortion based on the nonlinear parameters can be predicted.
