发酵过程监控与管理集散系统

:叙述了计算机控制技术在发酵过程中的应用 ,介绍了系统的主要功能、硬件配置及软件结构 。

Research on High-Accuracy Programmable Timer Used in Acquiring UWB Signals

UWB signal digitization depends, to a large extent, on the accuracy of sampling time. A highaccuracy programmable timer is therefore the key to implementing UWB signal data acquisition. A high-accuracy programmable timer based on the principle of ramp generators is described in this paper. The counting range of the timer is up to 16 bits, the timing precision is 8 ps, and the equivalent sampling rate is up to 50G Hz. No other identical product has been reported so far. This timer was successfully used in the data acquisition system for geological radar signals developed by us.

Reanalysis of the phylogenetic relationships of the Pentatomomorpha(Hemiptera: Heteroptera) based on ribosomal, Hox and mitochondrial genes

Pentatomomorpha is one of the most biodiverse infraorders among the true bugs（Hemiptera： Heteroptera）. Phylogenetic relationships among the superfamilies within this infraorder have been uncertain, especially for the Eutrichophora. The previous studies were based on morphological characters, or just mitochondrial or nuclear genes, or only partial 18 S rDNA and COI. In this study, we used maximum likelihood（ML） and Bayesian inference（BI） based on massive molecular datasets（18S rDNA, 28 S rDNA, Hox and mitochondrial genes totaling 21 loci and 12,538 characters） to infer a robust phylogeny for this terrestrial group. Results strongly support the monophyly of all superfamilies; the superfamily status of Aradoidea and the following relationships：（Aradoidea ＋（Pentatomoidea ＋（Coreoidea ＋（Lygaeoidea ＋ Pyrrhocoroidea）））） in Pentatomomorpha, and（Coreoidea ＋（Lygaeoidea ＋ Pyrrhocoroidea）） in Eutrichophora. Our results suggest that sampling greater numbers of genes is an effective tool for resolving phylogenetic problems.

Designing optimal number of receiving traces based on simulation model

Currently, the selection of receiving traces in geometry design is mostly based on the horizontal layered medium hypothesis, which is unable to meet survey requirements in a complex area. This paper estimates the optimal number of receiving traces in field geometry using a numerical simulation based on a field test conducted in previous research （Zhu et al., 2011）. A mathematical model is established for total energy and average efficiency energy using fixed trace spacing and optimal receiving traces are estimated. Seismic data acquired in a complex work area are used to verify the correctness of the proposed method. Results of model data calculations and actual data processing show that results are in agreement. This indicates that the proposed method is reasonable, correct, sufficiently scientific, and can be regarded as a novel method for use in seismic geometry design in complex geological regions.

On-Board Data Acquisition System for Automatic Shift System of Vehicle

Data acquisition, analysis and calibrating system affiliated with the vehicle is developed for the research on the automatic shift system (ASS). Considering the vehicle’s hard environment such as vibration, high and low temperature, electromagnetic disturbance and so on, the most suitable project is selected. PC104 transfers data with ECU by serial communication and a solid state disk is used as a FLASH ROM. Some techniques including frequency division of data is adopted in the software design in order to ensure the sampling frequency. The analysis and debug software is also contrived according to the characteristic of the ASS. The system plays an important role in the development of the ASS because of the good reliability and practicability in the application.

DISTRIBUTED SIMULATION SYSTEM BASED ON UNIVERSAL COMPONENTS

Based on MATRIXx, a universal real-time visual distributed simulation system is developed. The system can receive different input data from network or local terminal. Application models in the simulation modules can automatically get such data to be analyzed and calculated, and then produce real-time simulation control information. Meanwhile, this paper designs relevant simulation components to implement the input and output data, which can guarantee the real-time and universal of the data transmission. Result of the experimental system shows that the real-time performance of the simulation is perfect.

嵌入式软件测试平台配置

本文总结了建立软件评测中心必要条件,论述了软件测试过程并给出了各阶段的软件测试工具。在对市场充分调研的基础上,结合嵌入式软件的技术特点及具体工作需求,构建了一个嵌入式软件测试平台。

Question classification in question answering based on real-world web data sets

To improve question answering （QA） performance based on real-world web data sets,a new set of question classes and a general answer re-ranking model are defined.With pre-defined dictionary and grammatical analysis,the question classifier draws both semantic and grammatical information into information retrieval and machine learning methods in the form of various training features,including the question word,the main verb of the question,the dependency structure,the position of the main auxiliary verb,the main noun of the question,the top hypernym of the main noun,etc.Then the QA query results are re-ranked by question class information.Experiments show that the questions in real-world web data sets can be accurately classified by the classifier,and the QA results after re-ranking can be obviously improved.It is proved that with both semantic and grammatical information,applications such as QA, built upon real-world web data sets, can be improved,thus showing better performance.

A scheme on automated test data generation and its evaluation

By analyzing some existing test data generation methods, a new automated test data generation approach was presented. The linear predicate functions on a given path was directly used to construct a linear constrain system for input variables. Only when the predicate function is nonlinear, does the linear arithmetic representation need to be computed. If the entire predicate functions on the given path are linear, either the desired test data or the guarantee that the path is infeasible can be gotten from the solution of the constrain system. Otherwise, the iterative refining for the input is required to obtain the desired test data. Theoretical analysis and test results show that the approach is simple and effective, and takes less computation. The scheme can also be used to generate path-based test data for the programs with arrays and loops.

The safety parameters monitoring system for the coal mine based on CAN bus communication and intelligent data acquisition

In this paper,a monitoring and controlling system for the safety in production and environmental parameters of a small and medium-sized coal mine has been developed after analyzing the current domestic coal production and security conditions. The client computer can convert the analog signal about the safety in production and environmental parameters detected from the monitoring terminal into digital signal,and then,send the signal to the coal mine safety monitoring centre. This information can be analyzed,judged,and diagnosed by the monitoring-management-controlling software for helping the manager and technical workers to control the actual underground production and security situations. The system has many advantages including high reliability,better performance of real-time monitoring,faster data communicating and good practicability,and it can effectively prevent the occurrence of safety incidents in coal mines.

Analysis and Simulation of Molecular Dynamics of Lysozyme in Water Cluster System

The influence of water on protein conformation was investigated by simulating the molecular dynamics of a model protein lysozyme in different water systems.The lysozyme-water system with TIP3P water model and lysozyme-water cluster system with six-ring water model were evaluated.In addition,the radial distribution function of solvent around lysozyme was calculated.It is found that the distribution of water molecules around lysozyme is similar to that of water clusters.The analyses of dihedral angles and disulfide bonds of lysozyme show that the conformation of lysozyme is severely damaged in the lysozyme-water cluster system compared with that in the lysozyme-water system.This difference can be attributed to the formation of larger number of intermolecular hydrogen bonds between lysozyme and water cluster.It is in agreement with the analysis that water clusters can change the degree of denaturation in the process of heat denaturation of lysozyme.

Active velocity tomography for assessing rock burst hazards in a kilometer deep mine

Active velocity tomography was used to determine the stress state and rock burst hazards in a deep coal mine. The deepest longwall face, number 3207 in the Xingcun colliery, was the location of the field trials. The positive correlation between stress and seismic velocity was used to link the velocity data with stratum stresses. A GeoPen SE2404NT data acquisition system was used to collect seismic data from 300 g explosive charges fired by instantaneous electric detonator and located in the tail entry. The geophones were installed on the rock bolts in the head entry of LW3207. Velocity inversion shows an inhomogeneous distribution of stress in the longvvall face that could not be obtained from theory or numerical simulations. Three abnormally high P-wave velocity regions were identified that were located on the corners of the two roadways and at the face end near the rail entry side. The maximum velocity gradient is located at the open cut off near the rail entry and is the area most dangerous for rock burst. Mining-induced tremors recorded by a micro-seismic monitoring system demonstrated that the position of energy release during mining coincides with the high velocity gradient area. This technology aids technicians in the coal mine as they design measures to weaken or eliminate potential danger during subsequent mining.

In vitro effect of pantoprazole on lower esophageal sphincter tone in rats

AIM:To investigate the in vitro effects of pantoprazole on rat lower esophageal sphincter(LES)tone.METHODS:Rats weighing 250-300 g,provided by the Yeditepe University Experimental Research Center(Yü-DETAM),were used throughout the study.They were anesthetized before decapitation.LES tissues whose mucosal lining were removed were placed in a stan-dard 30-mL organ bath with a modif ied Krebs solution and continuously aerated with 95% oxygen-5% carbon dioxide gas mixture and kept at room temperature.The tissues were allowed to stabilize for 60 min.Sub-sequently,the contractile response to 10-6 mol/L carba-chol was obtained.Different concentrations of freshly prepared pantoprazole were added directly to the tis-sue bath to generate cumulative concentrations of 5×10-6 mol/L,5×10-5 mol/L,and 1.5×10-4 mol/L.Activi-ties were recorded on an online computer via a 4-channeltransducer data acquisition system using the software BSL PRO v 3.7,which also analyzed the data.RESULTS:Pantoprazole at 5×10-6 mol/L caused a small,but statistically insignif icant,relaxation in the car-bachol-contracted LES(2.23% vs 3.95%).The 5×10-5 mol/L concentration,however,caused a signif icant relax-ation of 10.47% compared with the control.1.5×10-4 mol/L concentration of pantoprazol caused a 19.89% relaxation in the carbachol contracted LES(P<0.001).CONCLUSION:This is the fi rst study to demonstrate that pantoprazole has a relaxing effect in isolated LESs.These results might have signif icant clinical implications for the subset of patients using proton pump inhibitors who do not receive full symptomatic alleviation from gastroesophageal reflux disease.

The future of remote ECG monitoring systems

Remote ECG monitoring systems are becoming commonplace medical devices for remote heart monitoring. In recent years, remote ECG monitoring systems have been applied in the monitoring of various kinds of heart diseases, and the quality of the transmission and re- ception of the ECG signals during remote process kept advancing. However, there remains accompanying challenges. This report focuses on the three components of the remote ECG monitoring system： patient （the end user）, the doctor workstation, and the remote server, reviewing and evaluating the imminent challenges on the wearable systems, packet loss in remote transmission, portable ECG monitoring system, pa- tient ECG data collection system, and ECG signals transmission including real-time processing ST segment, R wave, RR interval and QRS wave, etc. This paper tries to clarify the future developmental strategies of the ECG remote monitoring, which can be helpful in guiding the research and development of remote ECG monitoring.

Differentiating Data Collection for Cloud Environment Monitoring

In a growing number of information processing applications,data takes the form of continuous data streams rather than traditional stored databases.Monitoring systems that seek to provide monitoring services in cloud environment must be prepared to deal gracefully with huge data collections without compromising system performance.In this paper,we show that by using a concept of urgent data,our system can shorten the response time for most 'urgent' queries while guarantee lower bandwidth consumption.We argue that monitoring data can be treated differently.Some data capture critical system events;the arrival of these data will significantly influence the monitoring reaction speed which is called urgent data.High speed urgent data collections can help system to react in real time when facing fatal errors.A cloud environment in production,MagicCube,is used as a test bed.Extensive experiments over both real world and synthetic traces show that when using urgent data,monitoring system can lower the response latency compared with existing monitoring approaches.

Meta-information generation in distributed information system

The authors discuss the concept of meta information which is the description of information system or its subsystems, and proposes algorithms for meta information generation. Meta information can be generated in parallel mode and network computation can be used to accelerate meta information generation. Most existing rough set methods assume information system to be centralized and cannot be applied directly in distributed information system. Data integration, which is costly, is necessary for such existing methods. However, meta information integration will eliminate the need of data integration in many cases, since many rough set operations can be done straightforward based on meta information, and many existing methods can be modified based on meta information.

Parameter identification of the fractional-order systems based on a modified PSO algorithm

In order to better identify the parameters of the fractional-order system,a modified particle swarm optimization(MPSO)algorithm based on an improved Tent mapping is proposed.The MPSO algorithm is validated with eight classical test functions,and compared with the POS algorithm with adaptive time varying accelerators(ACPSO),the genetic algorithm(GA),a d the improved PSO algorithm with passive congregation(IPSO).Based on the systems with known model structures a d unknown model structures,the proposed algorithm is adopted to identify two typical fractional-order models.The results of parameter identification show that the application of average value of position information is beneficial to making f 11 use of the information exchange among individuals and speeds up the global searching speed.By introducing the uniformity and ergodicity of Tent mapping,the MPSO avoids the extreme v^ue of position information,so as not to fall into the local optimal value.In brief the MPSOalgorithm is an effective a d useful method with a fast convergence rate and high accuracy.

Integration of Agent System with Legacy Software

Agent technique is a new method that can analyze, design and realize a distributed open system. It has been used in almost every field. But if act for the real practical words in technique, it must integrate with legacy software, such as database system etc, and control them. This paper introduces the specification of agent software integration, ontology, instances database as implementing agent software integration with CORBA technique and takes XML, ACL as language communicating among agents.

Key technologies for the novel distributed numerical control integrated system

A novel distributed numerical control (DNC) integrated system based on plug-in software technology is proposed. It connects new or old numerical control (NC) machine tools which have inhomogeneous numerical control systems with CAD/CAM system by CANbus network. A DNC computer is able to control 15 sets of NC machine tools reliably at the same time. The novel DNC system increases the efficiency of machine tools and improve the production management level by realizing non-paper production, agile manufacturing, networked manufacturing and so on in the near future. Key technologies to construct the novel DNC integrated system include the integration of inhomogeneous numerical control systems, NC program restart, and algorithm for communication competition. Such system has demonstrated successful applications in some corporations that have acquired good economic benefits and social effects.

Data Reconstruction in Internet Traffic Matrix

Traffic matrix is an abstract representation of the traffic volume flowing between sets of source and destination pairs.It is a key input parameter of network operations management,planning,provisioning and traffic engineering.Traffic matrix is also important in the context of OpenFlow-based networks.Because even good measurement systems can suffer from errors and data collection systems can fail,missing values are common.Existing matrix completion methods do not consider traffic exhibit characteristics and only provide a finite precision.To address this problem,this paper proposes a novel approach based on compressive sensing and traffic self-similarity to reconstruct the missing traffic flow data.Firstly,we analyze the realworld traffic matrix,which all exhibit lowrank structure,temporal smoothness feature and spatial self-similarity.Then,we propose Self-Similarity and Temporal Compressive Sensing(SSTCS) algorithm to reconstruct the missing traffic data.The extensive experiments with the real-world traffic matrix show that our proposed SSTCS can significantly reduce data reconstruction errors and achieve satisfactory accuracy comparing with the existing solutions.Typically SSTCS can successfully reconstruct the traffic matrix with less than 32%errors when as much as98%of the data is missing.