推荐菱角形五通集料器

根据工艺要求,在粮油加工厂的通风除尘及气力输送风网中,经常出现四联组合刹克龙。其底座,即五通集料器的结构,多半采用平顶五通,并作为刹克龙的支承装置。

加热铣刨机螺旋集料器及链条张紧方式的改进

改进后的张紧结构在马达和链条之间增加了轴承座,径向力通过与小链轮连接的轴作用到轴承座上,对液压马达起到了很好的保护作用,并增加了装置的可靠性。

一种封闭式垂直螺旋卸车机

针对火车车厢运输的散料卸车现状,本文提出一种不用打开车厢门即可完成卸车工作且环保无污染的封闭式垂直螺旋卸车机。介绍了封闭式垂直螺旋卸车机的结构和工作原理。该卸车机为今后散料卸车提供一种新的思路。

Experiment and numerical simulation on flow and heat transfer in all-glass evacuated tube solar collectors

The experimental study of natural convection in allglass evacuated tube solar collectors is performed through the experimental platform of the solar-assisted fuel cell system.The experimental facility includes solar collectors with different length and diameter tubes, different coating materials, and with / without guide plates, respectively. Threedimensional mathematical models on natural and forced convections in the solar collectors are established and the experimental data is validated by field synergy and entransy principles. The results of natural convection show that the water temperature increases and thermal efficiency decreases gradually with the evacuated tube length. The thermal efficiency increases when absorption rates increase from 0. 95 to 1. 0 and emission rates decrease from 0. 16 to 0. 06. The thermal efficiency of solar collectors is increased after being equipped with the guide plate, which is attributed to the disappearance of the mixed flowand the enhancement of the heat transfer at the bottom of the evacuated tube. The results of forced convertion indicate that the Reynolds, Nusselt and entransy increments of the horizontal double collectors are higher than those of the vertical single collector while the entransy dissipation is lower than that of the vertical single collector. It is concluded that the solar collectors with guide plates are suitable for natural convection while the double horizontal collectors are suitable for forced convection in the thermal field of solar-assisted fuel cell systems with lowand medium temperatures.

Iron isotopic analyses of geological reference materials on MC-ICP-MS with instrumental mass bias corrected by three independent methods

Here we report iron(Fe) isotopic data of three pure Fe solution standards(IRMM-014, GSB Fe, and NIST3126a) and five widely used geological reference materials(RMs) from the United States Geological Survey and Geological Survey of Japan obtained on a Neptune Plus multi-collector–inductively coupled plasma–mass spectrometer(MC-ICP-MS) in our laboratory over the past 3 years. The instrumental mass bias was corrected by three independent methods: sample-standard bracketing(SSB),Ni doping + SSB, and ^(57)Fe–^(58)Fe double spike + SSB.Measurements reveal that both the Ni doping and double spike methods helped calibrate short-term fluctuations in mass bias. Collectively, almost all measurements of RMs yielded δ^(56)Fe within ± 0.05 of recommended values,provided that each sample was measured four times on MC-ICP-MS. For the first time, new recommended values for NIST SRM3126a are reported(δ^(56)Fe = 0.363 ± 0.006,2SE, 95% CI; and δ^(57)Fe = 0.534 ± 0.010, 2SE).

Metals Recovery from Fine Printed Circuit Boards Using Falcon SB Concentrator

Physical methods show great potential and advantages on comprehensive reutilization of waste printed circuit boards (PCBs) because of lower investment and operation cost, higher efficiency and environment friendliness. However, metals contained in fine fraction of PCBs cannot be recovered effectively by conventional equipments such as high tension electrostatic separator or shaking table. In the paper, this conundrum was resolved successfully with the enhanced Falcon SB concentrator. The separation mechanism of Falcon SB concentrator was analyzed and main factors affecting separation efficiency such as magnitude of rotation frequency of bowl, water counter pressure and slurry concentration of feed were studied and interaction of factors above also were investigated using Design-Expert software. Experiment results show that complete liberation degree and great difference of density between metals and nonmetals are suitable to recover metals from -74 μm PCBs using enhanced Falcon SB concentrator and 80.77 % integration efficiency can be achieved when slurry concentration of feed is 40 g/L with the water counter pressure of 0.01 MPa and rotation frequency of 50 Hz.

Calculation of Percentage of Coarse Aggregate Present in Concrete Using Processing of Digital Images Obtained with a Commercial Scanner

This paper presents a method for determining the percentage of coarse aggregate in concrete specimens by image processing. The test pieces were produced with the aim of obtaining images of their cross sections through a scanner table. In order to increase the contrast between mortar and coarse aggregate the sliced surfaces were treated with the phenolphthale in solution. The images obtained in the scanner were processed in a program developed with MATLAB （matrix laboratory）. The average coarse aggregate in each section and the mean of coarse aggregate per test body were calculated. With the results, it was revealed that the method returned satisfying results when compared to the original trace of the concrete.

Solar Desalination with Latent Heat Storage Materials and Solar Collector

Availability of clean water is going to become one of biggest demands of the country. Even though there arc various technologies available for purification of water harnessing solar energy fits the purpose for future problems. Distillation is one of many processes available for water purification, and solar energy is one of several forms of heat energy that can be used to energize this process. In this review a study is made to enhance the productivity of the solar stills by connecting solar still with latent heat storage and solar air heater in series and other factors like improving evaporation rate by maintaining Low depth, more exposure area, heat addition by solar collector and presence of latent heat storage material, which is a paraffin wax as a integral part of still. Latent heat storage is one of the most efficient ways of storing thermal energy. Unlike the sensible heat storage method, the latent heat storage method provides much higher storage density, with a smaller temperature difference between storing and releasing heat. Further augmentation of the yield by scraps, pebble, and sand are added.

Research on the Phase Change Solar Energy Fresh Air Thermal Storage System

In this article, a new kind of solar fresh air system is designed in order to realize the improvement of thermal efficiency by the integrated application of the PCMs and heat pipe technology. Under the adequate sunshine condition, the fresh air is directly delivered into the indoor environment after being heated by the solar collector. When the sun radiation is reduced, the heated air temperature can not satisfy the need of supply of air temperature.The main heat source is changed to phase change heat storage equipment instead of solar energy. The system adopt heat pipe for a high-efficiency and isothermal heat transfer which recover the shortcomings of PCMs such as： low coefficient of thermal conductivity and poor thermal efficiency. This article establishes the physical model of phase change solar energy fresh air thermal storage system and creates the mathematical model of its unsteady heat transfer to simulate and analyse the operation process by using Fluent software. The results of the study show that, compared to normal fresh air system, the phase change solar energy fresh air thermal storage system has a significant improvement in energy saving and indoor comfort level and will play an important role in the energy sustainable development.

Effect of Acoustic Resonance Phenomenon on Fluid Flow with Light Dust

In the present paper,the attention is focused on the characteristics of lightweight materials collection in the duct using acoustic resonance phenomena.The acoustic resonance was excited by using a controlled speaker at the middle of a test duct.We measured the sound pressure level,frequency response characteristics,acoustic damping ratio,mode shape,and lightweight materials response to acoustic resonance excited by a speaker.As a result,the acoustic damping ratio decreased as the mode number of acoustic resonance increased.The tissue strips and the lightweight materials were collected at the node of acoustic pressure when the acoustic resonance was excited.It was made clear that it is possible to control lightweight materials using acoustic resonance excited by a speaker.

Mechanics of flexible and stretchable piezoelectrics for energy harvesting

As rapid development in wearable/implantable electronic devices benefit human life in daily health monitoring and disease treatment medically, all kinds of flexible and/or stretchable electronic devices are booming, together with which is the demanding of energy supply with similar mechanical property. Due to its ability in converting mechanical energy lying in human body into electric energy, energy harvesters based on piezoelectric materials are promising for applications in wearable/implantable device's energy supply in a renewable, clean and life-long way. Here the mechanics of traditional piezoelectrics in energy harvesting is reviewed, including why piezoelectricity is the choice for minor energy harvesting to power the implantable/wearable electronics and how. Different kinds of up to date flexible piezoelectric devices for energy harvesting are introduced, such as nanogenerators based on Zn O and thin and conformal energy harvester based on PZT. A detailed theoretical model of the flexible thin film energy harvester based on PZT nanoribbons is summarized, together with the in vivo demonstration of energy harvesting by integrating it with swine heart. Then the initial researches on stretchable energy harvesters based on piezoelectric material in wavy or serpentine configuration are introduced as well.