The application areas of conventional push pull converters are limited because of high voltage stress of switches (twice of input voltage). This paper presents a novel zero voltage and zero current switching (ZCS)...The application areas of conventional push pull converters are limited because of high voltage stress of switches (twice of input voltage). This paper presents a novel zero voltage and zero current switching (ZCS) PWM push pull three level converter in which the voltage stress of switches is input voltage. With phase shifted modulation strategy, the leading switches can only realize zero voltage switching (ZVS), and the lagging switches can realize ZCS when block capacitor and block diodes are added. Using the strategy, the converter overcomes the drawbacks presented by the conventional push pull converter, such as magnetic aberration, large switch loss, and voltage spike on switches, so it can get higher efficiency, and a wider application area. The operating principle of the new converter is analyzed and verified on a 600 W, 50 kHz experimental prototype. Several zero voltage and zero current switching PWM push pull three level converters are proposed.展开更多
This paper proposes a family of PWM modulation strategies for boostfull-bridge (FB) converters. The modulation strategies can be classified into two kinds according tothe turn-on sequence of the diagonal switches. The...This paper proposes a family of PWM modulation strategies for boostfull-bridge (FB) converters. The modulation strategies can be classified into two kinds according tothe turn-on sequence of the diagonal switches. The concept of leading switches and lagging switchesis introduced to realize soft-switching. According to the soft-switching realized by the leadingswitches and the lagging switches, two kinds of soft-switching techniques for PWM boost FBconverters yield: zero-current-switching (ZCS) and zero-current and zero-voltage-switching (ZCZVS).Simulation results verify the analysis.展开更多
This paper proposes a zer o current and zero voltage switching (ZCZVS) PWM Boost full bridge (FB) conve rter. With series inductors, the leading switches can realize zero current swit ching (ZCS) in a wide load ra...This paper proposes a zer o current and zero voltage switching (ZCZVS) PWM Boost full bridge (FB) conve rter. With series inductors, the leading switches can realize zero current swit ching (ZCS) in a wide load range using the energy of the output capacitor. Ma king use of parasitic capacitors of the lagging switches and parallel auxiliary i nductance with the primary winding of the transformer, the lagging switches can realize zero voltage switching (ZVS) under any load. Compared with the ZCS PWM Boost FB converter, the new converter has no current duty cycle loss. Operat ional principle and parameter design are analyzed. Experimental results verify the effectiveness of the proposed converter.展开更多
The improved current-doubler-rectifier zero-voltage-switching PWM full-bridge converter (CDR ZVS PWM FB converter) achieves ZVS for the switches in a wide load range with the use of the energy stored in the output fil...The improved current-doubler-rectifier zero-voltage-switching PWM full-bridge converter (CDR ZVS PWM FB converter) achieves ZVS for the switches in a wide load range with the use of the energy stored in the output filter inductances, and the rectifier diodes commute naturally, therefore no oscillation and voltage spike occurs. The transformer needs no special manufacture method to limit the leakage inductance. The ZVS achievement and the design considerations for the output filter inductances and the blocking capacitor are discussed for the improved CDR ZVS PWM FB converter. A 540 W prototype converter is built in the lab to verify the operational principle and design considerations for the improved converter, the experimental results are also included.展开更多
A switched-current sample-and-hold circuit with low charge injection was proposed. To obtain low noise and charge injection, the zero-voltage switching was used to remove the signal-dependent charge injection, and the...A switched-current sample-and-hold circuit with low charge injection was proposed. To obtain low noise and charge injection, the zero-voltage switching was used to remove the signal-dependent charge injection, and the signal-independent charge injection was reduced by removing the feed-through voltage from the input port of the memory transistor directly. This current sample-and-hold circuit was implemented using CMOS 180 nm 1.8 V technology. For a 0.8 MHz sinusoidal signal input, the simulated signal-to-noise and distortion ratio and total harmonic distortion were improved from 53.74 dB and -51.24 dB to 56.53 dB and -54.36 dB at the sampling rate of 20 MHz respectively, with accuracy of 9.01 bit and power consumption of 0.44 mW.展开更多
文摘The application areas of conventional push pull converters are limited because of high voltage stress of switches (twice of input voltage). This paper presents a novel zero voltage and zero current switching (ZCS) PWM push pull three level converter in which the voltage stress of switches is input voltage. With phase shifted modulation strategy, the leading switches can only realize zero voltage switching (ZVS), and the lagging switches can realize ZCS when block capacitor and block diodes are added. Using the strategy, the converter overcomes the drawbacks presented by the conventional push pull converter, such as magnetic aberration, large switch loss, and voltage spike on switches, so it can get higher efficiency, and a wider application area. The operating principle of the new converter is analyzed and verified on a 600 W, 50 kHz experimental prototype. Several zero voltage and zero current switching PWM push pull three level converters are proposed.
文摘This paper proposes a family of PWM modulation strategies for boostfull-bridge (FB) converters. The modulation strategies can be classified into two kinds according tothe turn-on sequence of the diagonal switches. The concept of leading switches and lagging switchesis introduced to realize soft-switching. According to the soft-switching realized by the leadingswitches and the lagging switches, two kinds of soft-switching techniques for PWM boost FBconverters yield: zero-current-switching (ZCS) and zero-current and zero-voltage-switching (ZCZVS).Simulation results verify the analysis.
文摘This paper proposes a zer o current and zero voltage switching (ZCZVS) PWM Boost full bridge (FB) conve rter. With series inductors, the leading switches can realize zero current swit ching (ZCS) in a wide load range using the energy of the output capacitor. Ma king use of parasitic capacitors of the lagging switches and parallel auxiliary i nductance with the primary winding of the transformer, the lagging switches can realize zero voltage switching (ZVS) under any load. Compared with the ZCS PWM Boost FB converter, the new converter has no current duty cycle loss. Operat ional principle and parameter design are analyzed. Experimental results verify the effectiveness of the proposed converter.
文摘The improved current-doubler-rectifier zero-voltage-switching PWM full-bridge converter (CDR ZVS PWM FB converter) achieves ZVS for the switches in a wide load range with the use of the energy stored in the output filter inductances, and the rectifier diodes commute naturally, therefore no oscillation and voltage spike occurs. The transformer needs no special manufacture method to limit the leakage inductance. The ZVS achievement and the design considerations for the output filter inductances and the blocking capacitor are discussed for the improved CDR ZVS PWM FB converter. A 540 W prototype converter is built in the lab to verify the operational principle and design considerations for the improved converter, the experimental results are also included.
基金Supported by National Natural Science Foundation of China(No.61036004 and No.61076024)
文摘A switched-current sample-and-hold circuit with low charge injection was proposed. To obtain low noise and charge injection, the zero-voltage switching was used to remove the signal-dependent charge injection, and the signal-independent charge injection was reduced by removing the feed-through voltage from the input port of the memory transistor directly. This current sample-and-hold circuit was implemented using CMOS 180 nm 1.8 V technology. For a 0.8 MHz sinusoidal signal input, the simulated signal-to-noise and distortion ratio and total harmonic distortion were improved from 53.74 dB and -51.24 dB to 56.53 dB and -54.36 dB at the sampling rate of 20 MHz respectively, with accuracy of 9.01 bit and power consumption of 0.44 mW.
