频变系统特征问题及其灵敏度分析的扩阶法

当振动系统的物理矩阵（刚度矩阵和／或质量矩阵）是频率的函数时，该特征问题就变为非线性特征问题．由于振型的非正交性，使得非线性特征问题及其灵敏度分析存在困难．针对可展成幂级数形式的非线性特征问题，提出了一种通过初始系统矩阵的扩阶来使原非线性问题线性化的扩阶方法．该方法的优点是：由于在线性化过程中未引入任何误差，因而是精确的；可适用于强非线性特征问题；可求得系统的所有特征值及其灵敏度．数值示例表明，该方法虽很简单，但十分有效．

变速恒频风力发电系统最大风能追踪控制

根据风力机的特性,探讨了追踪、捕获最大风能的办法。在分析双馈发电机数学模型和磁场定向矢量控制的基础上,提出了基于定子磁链定向控制的变速恒频风力发电机的有功、无功功率的解耦控制策略,详细的仿真验证了控制策略的正确性和可行性。

频变振动系统特征解的一阶导数

讨论了频变系统固有振动的特点，证明了特征向量的非正交性．给出了特征值和振型一阶导数的两个算法。它们可用于这类系统的设计灵敏度分析和重分析。

一种频变传输线系统电磁脉冲响应的数值算法

在传输线系统电磁脉冲(EMP)响应的精确计算中,通常必须将端接负载的频变效应考虑在内,为此提出了一种端接频变负载传输线系统电磁脉冲响应的数值算法.首先,应用矢量网络分析仪或阻抗分析仪测试或计算得到端接频变负载电路的幅频特性和相频特性;然后,应用矢量匹配(VF)法对幅频特性和相频特性进行拟合,得到一系列极点、留数和常数项;最后,结合拟合得到的数据,应用时域有限差分(FDTD)法建立端接频变负载传输线系统的数值模型,并应用到分段线性递归卷积技术以提高卷积计算效率.所提算法具有较高的计算效率和精度,可应用于多种端接频变负载传输线系统电磁脉冲响应计算.

Stability of Oil Film and Output Speed of Hydroviscous Drive Affected by the Pressure of Control Oil

Based on the theories of hydraulics and nonlinear control system, the model of hydroviscous drive (HVD) was established, the influences of small ripple of control oil pressure on the output speed of HVD and the stability of oil film between friction disks were analyzed. The conclusion presents that when the frequency of the control oil's pressure ripple is higher than 60?Hz and the peak is less than 0 05?MPa, HVD can work stably. The result is useful for studying the application of frequency conversion technology in regulation of control oil pressure.

A graphic monitoring method for electric power of VVVF hydraulic system

In order to online monitor the running state of variable voltage and variable frequency(VVVF)hydraulic system,this paper presents a graphic monitoring method that fuses the information of variable frequency electric parameters.This paper first analyzes how the voltage and current of the motor stator change with the operation conditions of VVVF hydraulic system.As a result,we draw the relationship between the electric parameters(voltage and current)and power frequency.Then,the signals of the voltage and current are fused as dynamic figures based on the idea of Lissajous figures,and the values of the electric parameters are related to the features of the dynamic figures.Rigorous theoretical analysis establishes the function between the electric power of the variable frequency motor(VFM)and the features of the plotted dynamic figures including area of diagram,area of bounding rectangle,tilt angle,etc.Finally,the effectiveness of the proposed method is verified by two cases,in which the speed of VFM and the load of VVVF hydraulic system are changed.The results show that the increase of the speed of VFM enhances its three-phase electric power,but reduces the tilt angle of the plotted dynamic figures.In addition,as the load of VVVF hydraulic system is increased,the three-phase electric power of VFM and the tilt angle of the plotted dynamic figures are both increased.This paper provides a new way to online monitor the running state of VVVF hydraulic system.

The IMC Structure of Multi-rate Multivariable Predictive Control Systems and An Improved Algorithm

Multirate multivariable predictive control system with the sampling mechanism that adjusts the plant inputs only once but detects the plant outputs several times during a period is examined. The IMC structure of the system is derived, and its robust stability and zero steady state error characteristics are analyzed. A new control algorithm is developed by adding the variation of the outputs to the index performance. The simulation results show that the method is effective and has zeros steady-state error.

Research on the variable speed system of large power alternating current motor

The development status of the variable speed system of large power AC(alternating current)motor drive in China is introduced.The large power AC drive fed by AC-AC converters(cycloconverters)has developed greatly,and some innovations on the theory and engineering technique have been realized.They have been applied to rolling mills,mine hoists,and so on,and remarkable economic and social benefit has been achieved.The development of AC drive fed by large power IGCT(integrated gate commutated thyristors)AC-DC-AC converter is also introduced.It has excellent performance and reliable operation,and has been used in traction.

Acoustic emission characteristics and stress release rate of coal samples in different dynamic destruction time

Considering the importance of the prediction of rock burst disasters, and in order to grasp the law of acoustic emission(AE) of coal samples in different dynamic destruction time, the SH-II AE monitoring system was adopted to monitor the failure process of coal samples. The study of the change rule of the AE numbers, energy, ‘b' value and spectrum in the micro crack propagation process of the coal samples shows that as dynamic damage time went by, AE presented high-energy counts and the accumulated counts increased during the compression phase. The AE energy and cumulative counts increased during the elastic stage. The AE blank area increased gradually and the blank lines were more and more obvious in the molding stage. The AE counts and energy showed a trend of decrease in the residual damage phase.AE ‘b' values gradually became sparse, and the large scale cracks percentage compared with micro cracks decreased and the degree of damage decreased. The AE frequency spectrum peak went from the residual damage phase to the molding phase, and finally it was nearly stable, besides the bandwidth of the main frequency is gradually narrowed. Also, the frequency peak changed from single peak frequency to bi-peak frequency and to the single peak frequency. Uniaxial compressive strength is more sensitive than the elastic modulus to dynamic damage time.

High Voltage High Frequency Power Transformer for Pulsed Power Applications

This paper presents a new topology for a High Voltage （HV） 50 kV, High Frequency （HF） 20 kHz, multi-cored transformer suitable for use in pulsed power application systems. The main requirements are： high voltage capability, small size and weight. The HV, HF transformer is the main critical block of a high frequency power converter system. The transformer must have high electrical efficiency and in the proposed approach has to be optimized by the number of the cores. The transformer concept has been investigated analytically and through software simulations and experiments. This paper introduces the transformer topology and discusses the design procedure. Experimental measurements to predict core losses are also presented. The losses of epoxy coated nanocrystalline are compared to the losses in a new uncoated core.

Research on variable frequency and speed regulation of motor system based on PLC

This paper presents the composition, control scheme and signal processing method of frequency conversion motor speed testing system based on $7-200 PLC, and design the hardware circuit, the trapezoidal chart procedure and touch screen display program. The debugging test shows that the system is simple, practical, and related design work has laid the foundation for the future.

The feasibility experimental study of pumping and shunting pump under pressure in water injection station

At present in the process of water injection station operation, starting and stopping the pump caused system pressure fluctuations, and the fluctuations caused many problems about downstream injection wells. In order to eliminate the fluctuations and reduce problems, taking start pump, connect pump test under pressure in the water injection station installed the rotor frequency control system Changqing oil field developed. During the experiment, by progressively increasing the pressure pump to verify start pump with pressure feasibility test, the result shows when the pressure in the 0-25MPa pressure start and connect pump can be realized, and forecast the maximum pressure of the current start of the station with pressure pump. Start pump with pressure achieve the elimination of pressure fluctuations, provide the prerequisites about realizeing stable water injection pressure, and ultimately realize oil field water injection station to be automatic water injection laid a foundation.

The Applications of High-voltage variable frequency speed regulation System in Main Exhauster of Sintering

Main Exhauster is one of the main equipment of sintering production. It needs to consume a lot of electricity. Therefore, the system＇ s reconstruction for energy-saving will effectively reduce electricity for the production. The paper takes an iron and steel enterprise that had successfully transformed the synchronous motors of main exhauster of sintering as an example, which describes the application of high-voltage variable frequency speed regulation system in main exhauster of Sintering, so as to provide a reference for other iron and steel enterprises.

New energy power generation-wind power generation

This paper introduced the status quo of wind power and wind power generation technology. Focusing on the introduction of wind power generating system ibrational self-consistent field（VSCF）, program implementation included Alternating Current （AC）-Direct Current （DC）-AC conversion system, magnetic field modulation generator system, doubly-fed generator system etc. Among these, doubly-fed generator system is the trend. Where to build the wind farm is very important, so a perfect site is needed. Wind power generation will have a bright future. As long as the wind power can be linked to the grid in large scale.

STUDY ON THE CHARACTERISTICS OF LOW FREQUENCY SYNCHROMOTOR USED IN MINE HOIST SYSTEMS FED BY THE CYCLOINVERTER

The Low Frequency Synchromotor Drive Mine Hoist System fed by the cycloinverter has good features from the technological and economical point of view. According to the erating char acteristic of the mine hoist system, an advanced analysis is given to the construction, the operating characteristics and the harmonics of the magnetomotive force of the synchromotor fed by the cy cloinverter, and the beneficial suggestions are also given in this paper.

Dynamic test on waste heat recovery system with organic Rankine cycle

Dynamic performance is important to the controlling and monitoring of the organic Rankine cycle(ORC) system so to avoid the occurrence of unwanted conditions. A small scale waste heat recovery system with organic Rankine cycle was constructed and the dynamic behavior was presented. In the dynamic test, the pump was stopped and then started. In addition, there was a step change of the flue gas volume flow rate and the converter frequency of multistage pump, respectively. The results indicate that the working fluid flow rate has the shortest response time, followed by the expander inlet pressure and the expander inlet temperature.The operation frequency of pump is a key parameter for the ORC system. Due to a step change of pump frequency(39.49-35.24 Hz),the expander efficiency and thermal efficiency drop by 16% and 21% within 2 min, respectively. Besides, the saturated mixture can lead to an increase of the expander rotation speed.

Frequency Variations of Power System Due to Switching of Renewable Energy Sources

Power systems in Germany mainly containing intermittently operating renewable sources require load/frequency control which is performed up to now at the AC transmissioh and distribution levels. Frequency control can be achieved by employing short-and long-term storage plants buffering and complementing renewable energy sources. A representative grid consists of a natural-gas-fired plant serving as frequency leader, long-term storage plant, wind-power farm with associated short-term storage plantfor energy buffering, and photovoltaic farm with associated short-term storage plant interconnected by a long transmission line to two load circuits. Transient analysis is performed with Mathemafica solving the differential equation system for frequency variation. Powerflow through the AC transmission line is limited by its impedance. The long transmission line must be segmented to achieve stability and voltage control over an 800 km distance. The renewable plants must be operated together with the storage plants in order tominimize frequency variations by smoothing the power output of renewable plants, achieving step-wise control of the transmission-line power. Although to date only AC Iransmission lines in Germany exist, it is anticipated that within the next 10 years these will beaugmented by DC high-voltage lines.

Changes in Coupled Vibration Frequencies and Modes of Wall-Cavity Systems Induced by Stiffness Variation in the Structure

Problems of fluid structure interactions are governed by a set of fundamental parameters. This work aims at showing through simple examples the changes in natural vibration frequencies and mode shapes for wall-cavity systems when the structural rigidity is modified. Numerical results are constructed using ANSYS software with triangular finite elements for both the fluid （2D acoustic elements） and the solid （plane stress） domains. These former results are compared to proposed analytical expressions, showing an alternative benchmark tool for the analyst. Very rigid wall structures imply in frequencies and mode shapes almost identical to those achieved for an acoustic cavity with Neumann boundary condition at the interface. In this case, the wall behaves as rigid and fluid-structure system mode shapes are similar to those achieved for the uncoupled reservoir case.

Turbo-Coded Modulation of EVRC Speech Encoder with Unequal Error Protection for Fading Channels

The Enhanced Variable Rate Codec (EVRC) is a standard for the Speech Service Option 3 for Wideband Spread Spectrum Digital System, which has been employed in both IS-95 cellular systems and ANSI J-STC-008 PCS (Personal Communications Systems). This paper investigated the combination of turbo codes with Unequal Error Protection (UEP) and 16-QAM modulation for EVRC codec of Rate 1 to get power and bandwidth efficient coding scheme. The results show that the UEP system outperforms the Equal Error Protection (EEP) one by 1.45 dB at BER of 10 -5.

Brushless Doubly-Fed Induction Machine as a Variable Frequency Transformer

VFT （variable frequency transformer） has been recently used as art alternative to HVDC （high voltage direct current） to control power flow between asynchronous networks. VFT consumes less reactive power than a back-to-back HVDC system, provides faster initial transient recovery, and has better natural damping capability. VFT is simply a DFIM （doubly-fed induction machine） where the machine torque controls the power flow from stator to rotor and vice versa. The main disadvantage of this VFT is the slip rings and brushes required for the rotor circuit, especially in bulk power transmission. The BDFM （brushless doubly-fed machine） with nested cage rotor machine is proved to be a comparable alternative to conventional DFIM in many applications with the advantage that all windings being in the stator frame with fixed output terminals. In this paper, the BDFM is used as a BVFT （brushless variable frequency transformer）. A prototype machine is designed and simulated to verify the system validity.