基于电磁散射点间距的风电机雷达回波仿真

准确获取风电机雷达回波从而实现其独特性多普勒特征的提取,对解决风电场对雷达台站的无源干扰问题有重要意义。现有风电机回波积分算法忽视了散射点间距离散性,无法获取准确的风电机多普勒特征。为此,引入散射点间距参量,从雷达回波的基本方程出发,通过数学推演,获取了散射点间距对风电机回波影响的数学表征公式,从而提出了考虑散射点间距的风电机回波散射点算法。通过散射点间距不同取值范围的风电机回波时域分析,揭示了散射点间距对风电机回波多普勒特征的影响规律,实现了多普勒复杂特征的理论性解释。仿真结果表明,积分算法无法用于风电机回波保真性仿真,而合适取值下的散射点算法可以表征出风电机回波的复杂多普勒特征。

微电网的建模仿真研究

研究微电网的建模仿真问题,针对微电网中的微电源种类多样且输出特性各异,由传统的简易微电源模型所构成的微电网平台很难对现今微电网的研究进行仿真。针对以上情况,构建了结构、功能完整的风电机组、燃料电池、带有MPPT(最大功率点跟踪)光伏电池以及柴油发电机等微电源模型,及具有调频作用的二次负载模型,仿真验证了所建模型的合理性及有效性。在此基础上,又构建了一个含多种能源负荷的微型电网模型,对负荷突变及严重故障的条件下微电网维持电能质量和快速恢复的能力予以评估,结果表明所构建的微电源模型和微电网模型能较好地仿真实际情况,为微电网的进一步研究提供了良好的仿真平台。

Dynamic modelling and robust current control of wind-turbine driven DFIG during external AC voltage dip

Doubly-Fed Induction Generator （DFIG）, with vector control applied, is widely used in Variable-Speed Constant- Frequency （VSCF） wind energy generation system and shows good performance in maximum wind energy capture. But in two traditional vector control schemes, the equivalent stator magnetizing current is considered invariant in order to simplify the rotor current inner-loop controller. The two schemes can perform very well when the grid is in normal condition. However, when grid disturbance such as grid voltage dip or swell fault occurs, the control performance worsens, the rotor over current occurs and the Fault Ride-Through （FRT） capability of the DFIG wind energy generation system gets seriously deteriorated. An accurate DFIG model was used to deeply investigate the deficiency of the traditional vector control. The improved control schemes of two typical traditional vector control schemes used in DFIG were proposed, and simulation study of the proposed and traditional control schemes, with robust rotor current control using Internal Model Control （IMC） method, was carded out. The validity of the proposed modified schemes to control the rotor current and to improve the FRT capability of the DFIG wind energy generation system was proved by the comparison study.

Seismic Centrifuge Modelling of Offshore Wind Turbine with Tripod Foundation

The development of offshore wind energy is fast as it is clean, safe and of high efficiency. The harsh marine environment raises high demand on the foundation design of offshore wind turbine. Earthquake loading is one of the most significant factors which should be considered in the design phase. In this paper, a group of earthquake centrifuge tests were conducted on a physical wind turbine model with tripod foundation. The seismic responses of both wind turbine model and foundation soil were analyzed in terms of the recorded accelerations, pore water pressures, lateral displacements and settlements. The results were also compared with those measured in the previous research on mono-pile foundation. It is demonstrated that the tripod foundation can provide better resistance in the lateral displacement and structural settlement under earthquake loading.

Study on switched reluctance generator

The linear and non-linear math models of the switched reluctance generator (SRG) in generator mode were established in this work. The phase current and energy conversion process during generator operation were simulated by the linear math model. The non-linear math model was used to analyze the characteristics of the SRG operation in self-excitation mode and in separately-excitation mode. Some important findings on how the SRG is operated and controlled were obtained in this study, which provides theoretical basis for further design and experimental study.

Influential Factors of Bucket Foundation for Offshore Wind Turbine

In this paper, the influential design thctors of wide-shallow composite bucket foundation for 3 MW off- shore wind turbine are systematically studied by numerical simulation. The results show that the bucket diameter is larger than 27 m in generak and the range of 7--12 m is appropriate for cylinder height. In particular the bucket foun- dation with diameter of 30 m and cylinder height of 10 m is suitable for most soils. Under ultimate loads, the bucket diameter and elasticity modulus of soil have major effects on the deibrmability of bucket foundation, while the influ- ence of friction coefficient between the bucket and soil is relatively slight.

Numerical Flow Simulation in Turbine Mode of Counter-Rotating Type Pumping Unit to Cooperate with Wind Turbine

This serial research has proposed the hybrid power system combined the wind power unit with the counter-rotating type pump-turbine unit, to provide the constant output for the grid system, even at the suddenly fluctuating/turbulent wind circumstance. In this paper, the tandem impellers prepared for the counter-rotating type pumping unit were operated at the turbine mode, and the performances and the flow conditions were investigated numerically with accompanying the experimental results. Even though providing the pumping unit for the turbine mode, the maximum hydraulic efficiency is close to one of the counter-rotating type hydroelectric unit designed exclusively for the turbine mode. Besides, the runners/impellers of the unit work evidently so as to coincide the angular momentum change through the front runners/impellers with that through the rear runners/impellers, namely to take the axial flow at not only the inlet but also the outlet, without the guide vanes. From these results, it can be concluded that this type unit is effective to work at not only the pumping but also the turbine modes.

Impact of Wind Power on the ATC Values in Hydro-Dominated Power System

The wind power generation is increasing in many countries as a result of decreasing technology costs, active government policies for renewable energy sources, environmental concerns, etc.. This paper investigates the impact of wind power generation on ATC （available transmission capacity） calculation. In order to determine the maximum incremental MW transfer possible between two parts of a power system without violating any specified limits, ATCs are calculated. When calculating ATC values, it is necessary to assume production and consumption pattern in power system. Production of wind power depends on the wind speed, which is a random variable and it is impossible to forecast exactly the production of wind power that is needed for the ATCs calculation. In order to investigate influence of the stochastic wind power production on the ATCs value, computer model of Croatian electric power system is made in Power World Simulator. ATCs are calculated for southern part of Croatian power system in which besides wind power, hydro power plants are only type of power generation. Available wind speed measurements are used as input data for wind power production. The results of the ATC calculation for different scenario of wind power production and location in the Southern Croatian power system are presented and discussed in the paper.

State Modeling Based Prediction of Torsional Resonances for Horizontal-Axis Drive Train Wind Turbine

This paper focuses on the state space modeling approach and output torques prediction of torsional vibrations for variable speed wind turbines. The multi-body system model under study is mainly comprised of a wind turbine, a three stage planetary gear box and an induction generator. The masses-springs approach of shaft system differential equations is developed from Newton＇s law and Lagrange formulas. For an easy comprehension for electrical engineers and tutorial purpose, an electrical equivalent circuit of the system is proposed by using mechanical and electrical components similarities. Extensive numerical simulations are performed to investigate system mechanical resonances and impacts of damping factors on the system dynamic and stability.

Hazard Model Reliability Analysis Based on a Wind Generator Condition Monitoring System

This paper presents an application of the hazard model reliability analysis on wind generators, based on a condition monitoring system. The hazard model techniques are most widely used in the statistical analysis of the electric machine＇s lifetime data. The model can be utilized to perform appropriate maintenance decision-making based on the evaluation of the mean time to failures that occur on the wind generators due to high temperatures. The knowledge of the condition monitoring system is used to estimate the hazard failure, and survival rates, which allows the preventive maintenance approach to be performed accurately. A case study is presented to demonstrate the adequacy of the proposed method based on the condition monitoring data for two wind turbines. Such data are representative in the generator temperatures with respect to the expended operating hours of the selected wind turbines. In this context, the influence of the generator temperatures on the lifetime of the generators can be determined. The results of the study can be used to develop the predetermined maintenance program, which significantly reduces the maintenance and operation costs.

Validation of Full-Converter Wind Power Plant Generic Model Based on Actual Fault Ride-Through Measurements

Modeling and validation of full power converter wind turbine models with field measurement data are rarely reported in papers. In this paper an aggregated generic dynamic model of the wind farm consisting of full power converter wind turbines is composed and the model validation based on actual field measurements is performed. The paper is based on the measurements obtained from the real short circuit test applied to connection point of observed wind farm. The presented approach for validating the composed model and fault ride-through （FRT） capability for the whole wind park is unique in overall practice and its significance and importance is described and analyzed.