复合导线高电导性的实验及其应用前景

通过分析铜包钢线内导体和铜线内导体同轴电缆的电性能检测实验，从而证实银包钢导线的高电导特性。并指出该特性的应用前景和实用价值。

高强度高电导率材料研究概述

分析了长脉冲高强磁场导体材料的性能要求-高强度高电导率的结合,探讨了粒子强化材料和复合材料的强化机理和降低电阻率方法,回顾了形变Cu基原位复合材料的研究现状,分析了存在的问题和可能的应用场合.

复合导线高导性的机理分析

分析了复合导线在一定频域内的导电性能优于铜导线的高电导特性的物理实质，认为这种特性是由于电磁波在导线内部界面上的反射引起的。

沈文忠课题组研制出具有高电子迁移率的纳米硅薄膜

据1987年Phys.Rev.报道,纳米硅薄膜(nc-Si:H)是从上世纪80年代末兴起的一种新型人工功能纳米半导体材料.中国科学(A辑)记载,沈文忠课题组早在1992年已正式研制出来,指出它是一种具有高电导性、室温电导率高达10-1 Ω-1·cm-1,比本征单晶硅高出103倍.

复合导线高电导特性的机理分析

分析了复合导线在一定的频域,其导电性能优于铜导线的高电导特性的物理实质.认为,这种特性是由于电磁波在导线内部界面上的反射引起的.

集束拉拔法制备钢纤维增强铜基复合导线

将直径0.26 mm的铜包钢线集束装入铜管进行拉拔变形、800℃淬火中间处理、拉拔变形,制成钢纤维增强铜基复合导线.钢纤维在铜基体中均匀连续分布,钢纤维由铁素体与马氏体双相组织组成,铜、钢界面呈锯齿状.铜体积比为57%、变形率为2.8时,复合导线拉伸强度达到1256 MPa,相对电导率达到43.5%IACS,在大幅度降低铜含量的条件下,获得了良好的综合性能指标.

New pretreatment method for high-tension electrical separation of zircon from quartz

Electrostatic separation is one of the mineral processing methods based on mineral conductivity.This method has some significant problems such as being sensitive to humidity,high middling product,and impurity of non-conductive minerals.In this study,a new pretreatment method was proposed for the separation of zircon from quartz before electrostatic separation to solve these disadvantages.In this regard,two stages of pretreatment were applied which involved using collector of sodium dodecyl sulfate(SDS)for adjusting wettability of the zircon surface and spraying electrolyte aqueous solution to increase conductivity of the quartz surface.The effects of important parameters including pH,collector concentration,conditioning time,and concentration and type of electrolyte on the process efficiency were evaluated.The results showed that the optimal conditions of high-tension electrical separation were pH of 4,SDS concentration of 1×10-4 mol/L,conditioning time of 4 min and NaCl as an electrolyte with concentration of 4.27 mol/L.Separation efficiency of 95.12% was achieved in optimum conditions.This pretreatment method can be successfully used before high-tension electrical separation to separate the conductive or non-conductive minerals with various compositions.

Optical and Electrical Properties of Sensitized Polyaniline by Electrochemical Polymerization

To sensitize polyaniline with dyes by electrochemical polymerization, HClO 4 is employed as the dopant and oxidant, and the polyaniline with different sensitive properties is synthesized. The effect of sensitized emeraldine salt on the absorption spectrum is discussed in details. The maximum conductivity of sensitized films reaches 1.22 S/cm, and investigation on dye sensitizing of the polymer reveals that C.I. Direct Blue 71, C.I. Direct Blue 84, C.I. Direct Black 19 and CuPc-(COOH) 4 may enhance the photoconductivity of polyaniline greatly.

Fabrication of Highly Conductive Pd Nanowires using PDMS Transfer Method on DNA Scaffolds through Ethanol-Reduction

We have developed a simple, productive, and ettectlve poly（cllmetnysltoxane） rranu fer method to fabricate highly conductive Pd nanowires following DNA scaffolds on various substrates, based on ethanolreduction at low temperature. Pd nanoparticles were selectively deposited and confined onto the DNA templates on a PDMS sheet to form Pd nanowires and then the nanowires were transferred to other various substrates with a low occurrence of par asitic nanoparticles. The structure, morphology and the conductance of Pd nanowires were characterized with transmission electron microscopy, field emission scanning electron mi croscopy, and electrical transport measurement, respectively. Moreover, the growth process of the Pd nanowires was investigated by varying the incubation time and reaction temper ature. The present strategy provides a new method to fabricate extremely dense, highly conductive, and well aligned Pd nanowires on various substrates, which make it promising for building nanosensors and nanoelectronic devices.

Advancement in Materials for Supercapacitors

As future improvement to the energy density and power density of supercapacitors relies on the availability of new materials, worldwide research has been undertaken to address this need. The recent advancement in new materials used for fabricating supercapacitors is reviewed in this paper. Among the newly emerged materials covered in this review are the activated graphene, conductive polymers, CNT （carbon nantotubes）, AC （activated carbons）, carbon additives and metal oxides for EDLC （electric double layer capacitors） and pseudocapacitors applications.

Recent advances in chemical modifications of graphene

Graphene has attracted the interest of chemists, physicists, and materials scientists due to its extraordinary structural, mechanical, and electronic properties. While pristine graphene is desirable for applications that require a high electrical conductivity, many other applications require modified or functionalized forms of graphene, such as graphene oxide, reduced graphene, or other functionalized forms. Structurally modifying graphene through chemical functionalization reveals the numerous possibilities for tuning its structure; several chemical and physical functionalization methods have been explored to improve the stabilization and modification of graphene. In this review, we report recent progress towards the chemical modification of graphene, including both covalent and noncovalent methods, for use in various applications.

Direct synthesis of highly conductive poly（3,4- ethylenedioxythiophene）：poly（4-styrenesulfonate） （PEDOT：PSS）/graphene composites and their applications in energy harvesting systems

We report for the first time highly conductive poly（3,4-ethylenedioxythiophene）： poly（4-styrenesulfonate） （PEDOT：PSS）/graphene composites fabricated by in situ polymerization and their applications in a thermoelectric device and a platinum （Pt）-free dye-sensitized solar cell （DSSC） as energy harvesting systems. Graphene was dispersed in a solution of poly（4-styrenesulfonate） （PSS） and polymerization was directly carried out by addition of 3,4-ethylenedioxythiophene （EDOT） monomer to the dispersion. The content of the graphene was varied and optimized to give the highest electrical conductivity. The composite solution was ready to use without any reduction process because reduced graphene oxide was used. The fabricated film had a conductivity of 637 S.cm-1, corresponding to an enhancement of 41%, after the introduction of 3 wt.% graphene without any further complicated reduction processes of graphene being required. The highly conductive composite films were employed in an organic thermoelectric device, and the device showed a power factor of 45.7 μW·m^-1K^-2 which is 93% higher than a device based on pristine PEDOT：PSS. In addition, the highly conductive composite films were used in Pt-free DSSCs, showing an energy conversion efficiency of 5.4%, which is 21% higher than that of a DSSC based on PEDOT：PSS.

The genesis of tectono-magmatism in eastern China

The tectono-magmatism in eastern China is a hotspot for the researches, and many hypotheses of that were discussed. There is a middle crust with solid, low velocity and high conductivity in eastern China, which is impossible to form"convection magmatic layer". The subduction and compression of oceanic plate induced to the lateral pressure for the eastern China lithosphere in the condition of increasing pressure and decreasing temperature, it is also impossible to form an extensively melting magma layer. In South China, the granitic zone migrates from west to east, their evolution cannot be explained by plate subduction. The original magmatic reservoirs are controlled by main faults and spheres, which occurred the tectonic detachment and formed in the process of decreasing pressure and increasing temperature. The magma only originates in very small part of lithosphere. The tectono-magmatism and tectonic detachment of eastern China lithosphere during the Jurassic and the Cretaceous are concentrate mainly near the intersections between the regional faults and middle crust or the Moho discontinuity, and then magma intrudes or erupts along faults. The tectono-magmatism of Cenozoic originates near the intersections between the regional high-angle normal faults and the bottom of lithosphere. Obviously, the different penetration depth of faults induces a different kind of magmatism.

High efficiency bulk heterojunction organic solar cell by using high conductivity modified PEDOT:PSS as a buffer layer

In this paper,bulk heterojunction solar cells with poly-(3-hexylthiophene)(P3HT):[6,6]-phenyl-C61-butyric-acid-methylester(PCBM) as an active layer and modified poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate)(PEDOT:PSS) as a buffer layer are fabricated.The buffer layer is modified by adding 1% to 5% dimethyl sulfoxide(DMSO) into PEDOT:PSS solution before spin-coating.The conductivity of modified PEDOT:PSS and the performance of solar cells with modified PEDOT:PSS are measured.The highest conductivity of modified PEDOT:PSS with 4% DMSO can achieve 89.693 S/cm.The performance of organic solar cell with PEDOT:PSS modified by 4% DMSO is the best.The 4% DMSOmodified-PEDOT:PSS cell has a power conversion efficiency of 3.34%,V oc of 5.7 V,J sc of 14.56 mA/cm 2 and filling factor(FF) of 40.34%.

Fabrication and characteristic detection of graphene nanoelectrodes

Graphene has the advantages of high electrical conductivity,high heat conductivity,and low noise,which makes it a potential option for integrated circuits interconnection and nanoelectrodes.In this paper,we present a novel fabrication method for graphene nanoeletrodes with nanogap.First,graphene grown by chemical vapor deposition(CVD)is assembled to a chip with microelectrodes.Second,an atomic force microscopy(AFM)based mechanical cutting method is developed to cut the graphene into nanoribbons and nanoeletrodes with nanogap.Then the electronic property of a single nanodot is characterized using the garphene nanoelectrodes,demonstrating the effectiveness of the graphene nanoelectrodes.The fabricated graphene nanoeletrode pairs can be used as probes to detect single molecule in micro-environment,and show an attractive prospect for future molecular electronics applications.

Conductive Ni3(HITP)2 MOFs thin films for flexible transparent supercapacitors with high rate capability

The flexible transparent supercapacitors have been considered as one of the key energy-storage components to power the smart portable electronic devices.However,it is still a challenge to explore flexible transparent capacitive electrodes with high rate capability.Herein,conductive Ni3(HITP)2(HITP=2,3,6,7,10,11-hexaiminotriphenylene)thin films are adopted as capacitive electrodes in flexible transparent supercapacitors.The Ni3(HITP)2 electrode possesses the excellent optoelectronic property with optical transmittance(T)of 78.4%and sheet resistance(Rs)of 51.3Ωsq-1,remarkable areal capacitance(CA)of 1.63 mF cm^-2and highest scan rate up to 5000 mV s-1.The asymmetric Ni3(HITP)2//PEDOT:PSS supercapacitor(T=61%)yields a high CA of 1.06 mF cm^-2at 3μA cm-2,which maintains 77.4%as the current density increases by 50 folds.The remarkable rate capability is ascribed to the collaborative advantages of low diffusion resistance and high ion accessibility,resulting from the intrinsic conductivity,short oriented pores and large specific areas of Ni3(HITP)2 films.

Structural architectures of polymer proton exchange membranes suitable for high-temperature fuel cell applications

High-temperature proton exchange membrane(HT-PEM)fuel cells offer more advantages than low-temperature PEM fuel cells.The ideal characteristics of HT-PEMs are high conductivities,low-humidity operation conditions,adequate mechanical properties,and competitive costs.Various molecular moieties,such as benzimidazole,benzothiazole,imide,and ether ether ketone,have been introduced to polymer chain backbones to satisfy the application requirements for HT-PEMs.The most common sulfonated polymers based on the main chain backbones have been employed to improve the rties.Side group/chain engineering,including the introduction of SO_(3)^(-) on the side chain,grafting,branching,and crosslinking,has been widely applied to HTPEMs to further improve their proton conductivity,thermal stability,and mechanical properties.Currently,phosphoric acid-doped polybenzimidazole is the most successful polymer material for application in HT-PEMs.The compositing/blending modification methods of polymers are effective in obtaining high PA-doping levels and superior mechanical properties.In this review,the current progress of various membrane materials used for HT-PEMs is summarized.The synthesis and performance characteristics of polymers containing specific moieties in the chain backbones applied to HT-PEMs are discussed systemically.Various modification approaches and their deficiencies associated with HT-PEMs are analyzed and clarified.Prospects and future challenges are also presented.

Highly conductive and robust composite anion exchange membranes by incorporating quaternized MIL-101(Cr)

With well-defined channels and tunable functionality, metal-organic frameworks （MOFs） have inspired the design of a new class of ion-conductive compounds. In contrast to the extensive studies on proton- conductive MOFs and related membranes attractive for fuel cells, rare reports focus on MOFs in preparation of anion exchange membranes. In this study, chloromethylated MIL-101 （Cr） was prepared and incor- porated into chloromethylated poly （ether ether ketone） （PEEK） as a multifunctional filler to prepare imidazolium PEEK/imidazolium MIL-101（Cr） （ImPEEK/ImMIL-101（Cr）） anion exchange membrane after synchronous quaternization. The successful synthesis and chloromethylation of MIL-101（Cr） were veri- fied by transmission electron microscopy, X-ray diffraction and Fourier transform infrared spectroscopy while the enhanced performance of composite membranes in hydroxide conductivity, mechanical strength and dimensional stability were evaluated by alternating-current impedance, electronic stretching machine and measurement of swelling ratio. Specifically, incorporating 5.0wt% ImMIL-101（Cr） afforded a 71.4% increase in hydroxide conductivity at 20℃, 100% RH. Besides, the composite membranes exhibited enhanced dimensional stability and mechanical strength due to the rigid framework of ImMIL- 101（Cr）. At room temperature and the ImM1L-101（Cr） content of 10wt%, the swelling ratio of the ImPEEK/lmMIL-101（Cr） was 70.04% lower while the tensile strength was 47.5% higher than that of the pure membrane.

Low-power memristors based on layered 2D SnSe/graphene materials

The emerging two-terminal memristor with a conductance-adjustable function under external stimulation is considered a strong candidate for use in artificial memory and electronic synapses. However, the stability, uniformity, and power consumption of memristors are still challenging in neuromorphic computing. Here an Au/SnSe/graphene/SiO_(2)/Si memristor was fabricated, incorporating two-dimensional graphene with high thermal conductivity. The device not only exhibits excellent electrical characteristics(e.g., high stability,good uniformity and a high ROFF/RON ratio), but also can implement biological synaptic functions such as paired-pulse facilitation, short-term plasticity and long-term plasticity. Its set and reset power values can be as low as 16.7 and 2.3 nW,respectively. Meanwhile, the resistance switching mechanism for the device, which might be associated with the formation and rupture of a filamentary conducting path consisting of Sn vacancies, was confirmed by high-resolution transmission electron microscopy observations. The proposed device is an excellent candidate for use in high-density storage and lowpower neuromorphic computing applications.