腈纶长丝生产高缩率膨体毛条的技术探讨

为提高高缩率腈纶膨体毛条的缩率,满足纺织企业开发新产品的要求,文中采用2种腈纶长丝原料和不同的拉断机工艺,对毛条缩率的影响进行了对比试验。结果表明,采用高缩率长丝原料可有效地提高高缩率腈纶膨体毛条的缩率,生产出缩率大于28%的高缩条新产品。

生产高缩率膨体毛条的两种技术

为了提高高缩率腈纶膨体毛条(简称高缩条)的缩率,以满足纺织企业研发新产品的要求,采用两种腈纶长丝原料及分别优化的拉断机工艺,对高缩条缩率的影响进行了试验。试验结果表明:采用高缩率长丝原料可有效提高高缩条的缩率,生产出缩率大于28%的高缩条新产品。

混旦高缩率腈纶膨体毛条的生产工艺

本文论述了用拉断法直接制条生产高缩率腈纶膨体毛条的生产工艺。为使毛条缩率达到２６－２８％，着重优选了各种原料的配比，８７０拉断机的热牵伸倍数、热板温度、蒸汽压力、车速等工艺参数，使其制作的毛毯风格达到国外来样水平。

进口与国产腈纶长丝生产高缩率膨体毛条的质量分析

大庆石化公司腈纶厂给大庆毛毯厂带料加工从日本旭化成、东洋纺织进口的腈纶长丝。因此,对进口与国产腈纶长丝生产高缩率膨体毛条进行了质量分析。

高缩率有色腈纶膨体毛条的开发

凝胶染色工艺生产的高缩率有色毛条保证了腈纶纤维染色牢、颜色鲜艳、污水残余染料少。开发3.33dtex凝胶染色高缩率腈纶膨体毛条旨在发挥其手感柔软、厚实丰满、弹性、保暖性好等特点,为满足用户需求,做大下道工序的市场链奠定了基础。

Flow behavior and microstructure of ZK60 magnesium alloy compressed at high strain rate

Flow behavior and microstructure of a homogenized ZK60 magnesium alloy were investigated during compression in the temperature range of 250-400 ℃ and the strain rate range of 0.1-50 s^-1. The results showed that dynamic recrystallization （DRX） developed mainly at grain boundaries at lower strain rate （0.1-1 s^-1）, while in the case of higher strain rate （10-50 s^-1）, DRX occurred extensively both at twins and grain boundaries at all temperature range, especially at temperature lower than 350 ℃, which resulted in a more homogeneous microstructure than that under other deformation conditions. The DRX extent determines the hot workability of the workpiece, therefore, hot deformation at the strain rate of 10-50 s^-1 and in the temperature range of 250-350 ℃ was desirable for ZK60 alloy. Twin induced DRX during high strain rate compression included three steps. Firstly, twins with high dislocation subdivided the initial grain, then dislocation arrays subdivided the twins into subgrains, and after that DRX took place with a further increase of strain.

“减少若干倍”商兑

“减少若干倍”商兑林穗芳多年以前就有人指出过“减少若干倍”的说法不妥。由于没有引起普遍注意，加上翻译界对这个问题有不同看法，这种说法近年仍不时在出版物中出现。为了说明诸如此类的用法的表现形式，先从９０年代的书报刊和国外汉语广播中摘录一些实例，然后再讨...

Strain rate-dependent high temperature compressive deformation characteristics of ultrafine-grained pure aluminum produced by ECAP

To explore the effect of strain rate ε on the high temperature deformation characteristics of ultrafine-grained materials, the deformation and damage features as well as microstructures of ECAP-treated pure Al at different temperatures T and strain ratesε were systematically studied through compression tests and microscopic observations. The increase in ε eliminates strain softening at T≤473 K, and largely enhances the yield strength and flow stress at 473?573 K. The shear deformation dominates the plastic deformation of ECAP-treated Al. Many cracks along shear bands (SBs) are formed at T≥473 K and secondary SBs basically disappear at 1×10?3 s?1; however, at 1×10?2 s?1, cracks are only observed at temperature below 473 K, and secondary SBs become clearer at T≥473 K. The microstructures of ECAP-treated Al mainly consist of sub-grains (SGs). The increase in ε inhibits the SG growth, thus leading to the increases both in yield strength and flow stress at high temperatures.

Compressive behavior of high particle content B_4C/Al composite at elevated temperature

The compressive properties of the aluminum matrix composite reinforced with 55% B4C （volume fraction） particles were characterized using Gleeble 3500 thermal-mechanical testing machine. The compressive stress--strain curves were obtained at the temperature ranging from 298 to 773 K and strain rate ranging from 1×10^（-3） to 5 s ^（-1）. The results showed that the dynamic compressive strength decreased more slowly than the quasi-static compressive strength at elevated temperatures, which was attributed to the different failure modes of the composite under dynamic and quasi-static load. The strain rate sensitivity increased from 0.02 to 0.13 when the temperature increased from room temperature to 773 K, suggesting that the strain rate sensitivity of this type of composite is a function of temperature.

Climate change and glacier area variations in China during the past half century

Glacier variations in the Tibetan Plateau and surrounding mountain ranges in China affect the livelihood of over one billion people who depend on water from the Yellow, Yangtze, Brahmaputra, Ganges and Indus rivers originating in these areas. Based on the results of the present study and published literature, we found that the glaciers shrank ：5.7% in area from 1963 to 20：0 with an annual area change of -0.33%. The shrinkage generally decreased from peripheral mountain ranges to the interior of Tibet. The linear trends of annual air temperature and precipitation at 147 stations were 0.36℃（10a）^-1 and 8.96 mm （10a）^-1 respectively from 1961 to 2010. The shrinkage of glaciers was well correlated with the rising temperature and the spatial patterns of the shrinkage were influenced by other factors superimposed on the rising temperature such as glacier size, type, elevation, debris cover and precipitation.

Characterization of hot deformation behavior of Al-Zn-Mg-Mn-Zr alloy during compression at elevated temperature

The hot deformation behavior of Al-6.2Zn-0.70Mg-0.30Mn-0.17 Zr alloy and its microstructural evolution were investigated by isothermal compression test in the deformation temperature range between 623 and 773 K and the strain rate range between 0.01 and 20 s^(-1).The results show that the flow stress decreased with decreasing strain rate and increasing deformation temperature.At low deformation temperature(≤673 K) and high strain rate(≥1 s^(-1)),the main flow softening was caused by dynamic recovery;conversely,at higher deformation temperature and lower strain rate,the main flow softening was caused by dynamic recrystallization.Moreover,the slipping mechanism transformed from dislocation glide to grain boundary sliding with increasing the deformation temperature and decreasing the strain rate.According to TEM observation,numerous Al_3Zr particles precipitated in matrix,which could effectively inhibit the dynamic recrystallization of the alloy.Based on the processing map,the optimum processing conditions for experimental alloy were in deformation temperature range from 730 K to 773 K and strain rate range from 0.033 s^(-1) to 0.18 s^(-1) with the maximum efficiency of 39%.

Subtransus deformation mechanisms of TC11 titanium alloy with lamellar structure

Isothermal compression tests are applied to study the deformation mechanisms of TCll titanium alloy with lamellar structure under the deformation temperature range of 890-995 ℃ and strain rate range of 0.01-10 s^-1. According to the flow stress data obtained by compression tests, the deformation activations are calculated based on kinetics analysis of high temperature deformation, which are then used for deformation mechanism analysis combined with microstructure investigation. The results show that deformation mechanisms vary with deformation conditions： at low strain rate range, the deformation mechanism is mainly dislocation slip; at low temperature and high strain rate range, twinning is the main mechanism; at high temperature and high strain rate range, the deformation is mainly controlled by diffusion offl phase.

Low sidelobe robust imaging in random frequency-hopping wideband radar based on compressed sensing

High resolution range imaging with correlation processing suffers from high sidelobe pedestal in random frequency-hopping wideband radar. After the factors which affect the sidelobe pedestal being analyzed, a compressed sensing based algorithm for high resolution range imaging and a new minimized ll-norm criterion for motion compensation are proposed. The random hopping of the transmitted carrier frequency is converted to restricted isometry property of the observing matrix. Then practical problems of imaging model solution and signal parameter design are resolved. Due to the particularity of the proposed algorithm, two new indicators of range profile, i.e., average signal to sidelobe ratio and local similarity, are defined. The chamber measured data are adopted to testify the validity of the proposed algorithm, and simulations are performed to analyze the precision of velocity measurement as well as the performance of motion compensation. The simulation results show that the proposed algorithm has such advantages as high precision velocity measurement, low sidelobe and short period imaging, which ensure robust imaging for moving targets when signal-to-noise ratio is above 10 dB.

Influence of Filter Cloth on the Cathode on the Electroosmotic Dewatering of Activated Sludge

The mechanical dewatering of activated sludge is troublesome due to its high compressibility of solids. The dewatering can be enhanced dramatically by the use of electroosmosis,in which an electric field is applied to the sludge cake.In this study,the influence of filter cloth on the cathode on the dewatering of activated sludge was investigated.It was found that thicker filter cloth led to lower water removal from the sludge cake,so a stainless steel cathode net with small pore size instead of filter cloth was applied,which improves the dewatering efficiency and reduces the electric power consumption.Moreover,water absorbent materials were helpful to remove the water from the sludge cake.For the electroosmotic dewatering at 7 kPa and 24 V·cm-1,the water content in the sludge cake decreased to 60%(by mass) with the average 0.075 kW·h·kg-1of water removed by using the cathode net.

Hot deformation behavior and constitutive relationship of Q420qE steel

Isothermal compression tests at temperatures from 1 273 to l 423 K and strain rates from 0.1 to 10 s-q were carried out to investigate the flow behaviors of Q420qE steel. Stress-strain data collected from the tests were employed to establish the constitutive equation, in which the influence of strain was incorporated by considering the effect of strain on material constants Q, n, a, and lnA. The results show that the flow stress curves are dependent on the strain, strain rate and deformation temperature. They display typical dynamic recrystallization behavior and consist of three stages, i.e., hardening stage, softening stage and steady stage. The flow stress decreases with increasing the deformation temperature and decreasing the strain rate. In addition, the flow stress data predicted by the proposed constitutive model agree well with the corresponding experimental results, and the correlation coefficient and the average absolute relative error between them are 0.990 3 and 3.686%, respectively.

Fourth order accurate compact scheme with group velocity control (GVC)

For solving complex flow field with multi-scale structure higher order accurate schemes are preferred. Among high order schemes the compact schemes have higher resolving efficiency. When the compact and upwind compact schemes are used to solve aerodynamic problems there are numerical oscillations near the shocks. The reason of oscillation production is because of non-uniform group velocity of wave packets in numerical solutions. For improvement of resolution of the shock a parameter function is introduced in compact scheme to control the group velocity. The newly developed method is simple. It has higher accuracy and less stencil of grid points.

Low strain rate compressive behavior of high porosity closed-cell aluminum foams

The impact of a rigid body(protected structure) together with cushion material(cellular metal foam) on hard ground from a fixed height was investigated.An analytical one-degree-of-freedom colliding model(ODF-CM) was established to analyze the protection ability and energy absorption by the foam under low velocity impact conditions.For validation,drop hammer experiments were carried out for high porosity closed-cell aluminum foam specimens subjected to low velocity impact loading.The dynamic deformation behavior of the specimen was observed and the velocity attenuation of the drop hammer was measured.The results demonstrated that the aluminum foam had excellent energy absorption capabilities,with its dynamic compressive behavior similar to that obtained under quasi-static loading conditions.Finite element method(FEM) was subsequently employed to obtain stress distributions in the foam specimen.As the propagating period of stress in the specimen was far less than the duration of attenuation,the evolution of the stress was similar to that under quasi-static loading conditions and no obvious stress wave effect was observed,which agreed with the experimental observation.Finally,the predicted velocity attenuation by the ODF-CM was compared with both the experimental measurements and FEM simulation,and good agreements were achieved when the stress distribution was considered to be uniform and the "quasi-static" compressive properties are employed.