采用CALPHAD(calculation of phase diagram)方法对Fe-V和Ni-V二元系进行了热力学优化,并结合第一性原理计算,利用(A,B)_(10)(A,B)_(4)(A,B)_(16)三亚点阵模型描述σ相,首次成功地描述了σ相的占位分数。使用优化的模型参数不仅可以描述...采用CALPHAD(calculation of phase diagram)方法对Fe-V和Ni-V二元系进行了热力学优化,并结合第一性原理计算,利用(A,B)_(10)(A,B)_(4)(A,B)_(16)三亚点阵模型描述σ相,首次成功地描述了σ相的占位分数。使用优化的模型参数不仅可以描述Fe-V和Ni-V系热化学性质,而且可以很好地重现Fe-V和Ni-V系的相平衡关系,为高熵合金多组元热力学数据库的建立奠定基础。展开更多
针对核电厂循环水冲洗泵盖板表面结构完整性破坏失效的工程问题,基于冷金属过渡技术(Cold metal transfer,CMT),开展了CuAl9Ni3Fe2铝青铜合金电弧增材修复工艺的研究。通过单层单道成形、单层多道搭接成形以及多层多道试验研究,确定并...针对核电厂循环水冲洗泵盖板表面结构完整性破坏失效的工程问题,基于冷金属过渡技术(Cold metal transfer,CMT),开展了CuAl9Ni3Fe2铝青铜合金电弧增材修复工艺的研究。通过单层单道成形、单层多道搭接成形以及多层多道试验研究,确定并固化了一套CuAl9Ni3Fe2铝青铜合金CMT增材修复工艺的关键参数;并借鉴已有成熟的核电设备制造工程实践,参考RCC-M规范要求,制定了该修复工艺的验证试验要求,明确了试验项目、试验标准及验收指标,并按要求完成试件的制备及试验。结果表明:采用研发的CMT增材修复工艺制备的熔敷金属外观成形优良,内部致密无缺陷且与母材熔合良好,力学性能与母材相当,各项试验结果均满足验收指标。可用于CuAl9Ni3Fe2铝青铜合金的CMT增材制造及修复。展开更多
In this paper the tensile properties of both ordered and disordered Ni-24Fe and Ni-24Fe-0.03%B （wt%） alloys in gaseous hydrogen was investigated. The result shows that the ductility of the disordered Ni3Fe is signif...In this paper the tensile properties of both ordered and disordered Ni-24Fe and Ni-24Fe-0.03%B （wt%） alloys in gaseous hydrogen was investigated. The result shows that the ductility of the disordered Ni3Fe is significantly larger than that of ordered material in gaseous hydrogen. However, the ductility of ordered Ni3Fe doped with 0.03%B is nearly the same as that of disordered one indicating the obvious suppressing effect of boron on the H2-induced embrittlement. Based on the segregation behavior of boron in Ni3A1, it is proposed that the suppressing effect of boron in Ni3Fe on the H2-induced embrittlement is attributed to the segregation of boron on grain boundaries, thereby reducing the hydrogen diffusivity along the grain boundaries.展开更多
The natural passive films forrned on Fe_(40)Ni_(40)P_(14)B_6 and Fe_(54.6)Ni_(38)Si_(4.1)B_(2.3)V_1 amorphous alloys long-term exposed in air have been studied by X-ray photoelectron spectroscopy (XPS) and Auger elect...The natural passive films forrned on Fe_(40)Ni_(40)P_(14)B_6 and Fe_(54.6)Ni_(38)Si_(4.1)B_(2.3)V_1 amorphous alloys long-term exposed in air have been studied by X-ray photoelectron spectroscopy (XPS) and Auger electron (including Ar+ ion depth profiling) spectroscopy (AES). The following aspects have been investigated: (1) chemical states of the elements in the films. binding energies and the chemical shifts measured by XPSf (2) structure and composition of the films fand (3) thickness of the passive films determined by AES depth profiling and XPS analysis.展开更多
This work reports the enhancing effect of a highly cost effective and efficient metal, Fe, incorporation to Co or Ni based Mo/Al2O3 catalysts in the oxidative desulfurization （ODS） of dibenzothiophene （DBT） using ...This work reports the enhancing effect of a highly cost effective and efficient metal, Fe, incorporation to Co or Ni based Mo/Al2O3 catalysts in the oxidative desulfurization （ODS） of dibenzothiophene （DBT） using H2O2 and formic acid as oxidants. The influence of operating parameters i.e. reaction time, catalyst dose, reaction temperature and oxidant amount on oxidation process was investigated. Results revealed that 99% DBT conversion was achieved at 60℃ and 150 min reaction time over Fe-Ni-Mo/Al2O3. Fe tremendously enhanced the ODS activity of Co or Ni based Mo/Al2O3 catalysts following the activity order：Fe-Ni-Mo/Al2O3 〉 Fe-Co-Mo/Al2O3 〉 Ni-Mo/Al2O3 〉 Co-Mo/Al2O3, while H2O2 exhibited higher oxidation activity than formic acid over all catalyst systems. Insight about the surface morphology and textural properties of fresh and spent catalysts were achieved using scanning electron microscopy （SEM）, X-ray diffraction （XRD）, energy dispersive X-ray （EDX） analysis, Atomic Absorption Spectroscopy （AAS） and BET surface area analysis, which helped in the interpretation of experimental data. The present study can be deemed as an effective approach on industrial level for ODS of fuel oils crediting to its high efficiency, low process/catalyst cost, safety and mild operating condition.展开更多
TEM study was made to explore the mechanism of the strain-age hardening of initially-dis- ordered (Co_(78)Fe_(22))_3V,which was found to be attributed to the formation of a special disloca- tion-stacking fault configu...TEM study was made to explore the mechanism of the strain-age hardening of initially-dis- ordered (Co_(78)Fe_(22))_3V,which was found to be attributed to the formation of a special disloca- tion-stacking fault configuration in company with disorder-order transformation-disloca- tions extended to stacking faults on{111}planes and got connected with each other through partial dislocation reaction at intersections of{111}planes,leading to dense networks with cells bounded by stacking fault tetrahedrons.The results also indicated that ordered (Co_(78)Fe_(22))_3V has very low stacking fault energy on{111}planes and relative high and isotropie antiphase boundary energy,which implies that it is most likely to be Lomer-Cottrell locks,not Kear-Wilsdof locks,that are responsible for the high strength at high temperatures of this alloy.展开更多
The behaviour of hydrogen permeation and diffusion in amorphous alloy Ni68Cr7Si8B14Fe3 hasbeen investigated by an ultrahigh vacuum gas permeation technique. A comparison experimentwas carried out between the as-quench...The behaviour of hydrogen permeation and diffusion in amorphous alloy Ni68Cr7Si8B14Fe3 hasbeen investigated by an ultrahigh vacuum gas permeation technique. A comparison experimentwas carried out between the as-quenched and annealed States (400℃/2h) of the amorphousalloy. The results show that, for both states of the amorphous alloy in the temperature rangeof 200～350℃, the diffusivity and permeability of hydrogen are in agreement with Arrheniusrelationship, there does not exist H-trapping effect, and the activation energies of diffusion andpermeation almost keep the same.展开更多
Cavitation erosion behavior of as-welded Cu12Mn8Al3Fe2Ni alloy in 3.5% NaCl aqueous solution was studied bymagnetostrictive vibratory device for cavitation erosion. The results show that the cavitation erosion resista...Cavitation erosion behavior of as-welded Cu12Mn8Al3Fe2Ni alloy in 3.5% NaCl aqueous solution was studied bymagnetostrictive vibratory device for cavitation erosion. The results show that the cavitation erosion resistance ofthe as-welded Cu12Mn8Al3Fe2Ni alloy is much more superior to that of the as-cast one. The cumulative mass lossand the mass loss rate of the as-welded Cu12Mn8Al3Fe2Ni alloy are almost 1/4 that of the as-cast one. SEM analysisof eroded specimens reveals that the as-cast Cu12Mn8Al3Fe2Ni alloy is attacked more severely than the as-weldedone. Microcracks causing cavitation damage initiate at the phase boundaries.展开更多
A new isopolyoxovanadate [Ni(1,10′-phen) 3] 2 [V Ⅳ 2V Ⅴ 8O 26] was hydrothermally synthesized and structurally characterized by the single crystal X-ray diffraction. The compound crystallizes in orthorhombic system...A new isopolyoxovanadate [Ni(1,10′-phen) 3] 2 [V Ⅳ 2V Ⅴ 8O 26] was hydrothermally synthesized and structurally characterized by the single crystal X-ray diffraction. The compound crystallizes in orthorhombic system, space group Pbcn with a=1.362 9(3) nm, b=2.215 6(4) nm, c= 2.571 2(4) nm, V=7.764(2) nm 3, Z=4, R=0.040 3, wR 2=0.044 6. The compound exhibits an unusual empty ellipsoidal cage, which is constructed by eight {V ⅤO 4} tetrahedra and two {V ⅣO 5} square pyramids via corner-sharing modes. The chiral [Ni(1,10′-phen) 3] 2+ complexes act as the counter cations.展开更多
文摘采用CALPHAD(calculation of phase diagram)方法对Fe-V和Ni-V二元系进行了热力学优化,并结合第一性原理计算,利用(A,B)_(10)(A,B)_(4)(A,B)_(16)三亚点阵模型描述σ相,首次成功地描述了σ相的占位分数。使用优化的模型参数不仅可以描述Fe-V和Ni-V系热化学性质,而且可以很好地重现Fe-V和Ni-V系的相平衡关系,为高熵合金多组元热力学数据库的建立奠定基础。
文摘针对核电厂循环水冲洗泵盖板表面结构完整性破坏失效的工程问题,基于冷金属过渡技术(Cold metal transfer,CMT),开展了CuAl9Ni3Fe2铝青铜合金电弧增材修复工艺的研究。通过单层单道成形、单层多道搭接成形以及多层多道试验研究,确定并固化了一套CuAl9Ni3Fe2铝青铜合金CMT增材修复工艺的关键参数;并借鉴已有成熟的核电设备制造工程实践,参考RCC-M规范要求,制定了该修复工艺的验证试验要求,明确了试验项目、试验标准及验收指标,并按要求完成试件的制备及试验。结果表明:采用研发的CMT增材修复工艺制备的熔敷金属外观成形优良,内部致密无缺陷且与母材熔合良好,力学性能与母材相当,各项试验结果均满足验收指标。可用于CuAl9Ni3Fe2铝青铜合金的CMT增材制造及修复。
基金Project supported by the National Natural Science Foundation of China （Grant Nos. 50371050, 50671057）
文摘In this paper the tensile properties of both ordered and disordered Ni-24Fe and Ni-24Fe-0.03%B （wt%） alloys in gaseous hydrogen was investigated. The result shows that the ductility of the disordered Ni3Fe is significantly larger than that of ordered material in gaseous hydrogen. However, the ductility of ordered Ni3Fe doped with 0.03%B is nearly the same as that of disordered one indicating the obvious suppressing effect of boron on the H2-induced embrittlement. Based on the segregation behavior of boron in Ni3A1, it is proposed that the suppressing effect of boron in Ni3Fe on the H2-induced embrittlement is attributed to the segregation of boron on grain boundaries, thereby reducing the hydrogen diffusivity along the grain boundaries.
文摘The natural passive films forrned on Fe_(40)Ni_(40)P_(14)B_6 and Fe_(54.6)Ni_(38)Si_(4.1)B_(2.3)V_1 amorphous alloys long-term exposed in air have been studied by X-ray photoelectron spectroscopy (XPS) and Auger electron (including Ar+ ion depth profiling) spectroscopy (AES). The following aspects have been investigated: (1) chemical states of the elements in the films. binding energies and the chemical shifts measured by XPSf (2) structure and composition of the films fand (3) thickness of the passive films determined by AES depth profiling and XPS analysis.
文摘This work reports the enhancing effect of a highly cost effective and efficient metal, Fe, incorporation to Co or Ni based Mo/Al2O3 catalysts in the oxidative desulfurization （ODS） of dibenzothiophene （DBT） using H2O2 and formic acid as oxidants. The influence of operating parameters i.e. reaction time, catalyst dose, reaction temperature and oxidant amount on oxidation process was investigated. Results revealed that 99% DBT conversion was achieved at 60℃ and 150 min reaction time over Fe-Ni-Mo/Al2O3. Fe tremendously enhanced the ODS activity of Co or Ni based Mo/Al2O3 catalysts following the activity order：Fe-Ni-Mo/Al2O3 〉 Fe-Co-Mo/Al2O3 〉 Ni-Mo/Al2O3 〉 Co-Mo/Al2O3, while H2O2 exhibited higher oxidation activity than formic acid over all catalyst systems. Insight about the surface morphology and textural properties of fresh and spent catalysts were achieved using scanning electron microscopy （SEM）, X-ray diffraction （XRD）, energy dispersive X-ray （EDX） analysis, Atomic Absorption Spectroscopy （AAS） and BET surface area analysis, which helped in the interpretation of experimental data. The present study can be deemed as an effective approach on industrial level for ODS of fuel oils crediting to its high efficiency, low process/catalyst cost, safety and mild operating condition.
文摘TEM study was made to explore the mechanism of the strain-age hardening of initially-dis- ordered (Co_(78)Fe_(22))_3V,which was found to be attributed to the formation of a special disloca- tion-stacking fault configuration in company with disorder-order transformation-disloca- tions extended to stacking faults on{111}planes and got connected with each other through partial dislocation reaction at intersections of{111}planes,leading to dense networks with cells bounded by stacking fault tetrahedrons.The results also indicated that ordered (Co_(78)Fe_(22))_3V has very low stacking fault energy on{111}planes and relative high and isotropie antiphase boundary energy,which implies that it is most likely to be Lomer-Cottrell locks,not Kear-Wilsdof locks,that are responsible for the high strength at high temperatures of this alloy.
文摘The behaviour of hydrogen permeation and diffusion in amorphous alloy Ni68Cr7Si8B14Fe3 hasbeen investigated by an ultrahigh vacuum gas permeation technique. A comparison experimentwas carried out between the as-quenched and annealed States (400℃/2h) of the amorphousalloy. The results show that, for both states of the amorphous alloy in the temperature rangeof 200～350℃, the diffusivity and permeability of hydrogen are in agreement with Arrheniusrelationship, there does not exist H-trapping effect, and the activation energies of diffusion andpermeation almost keep the same.
文摘Cavitation erosion behavior of as-welded Cu12Mn8Al3Fe2Ni alloy in 3.5% NaCl aqueous solution was studied bymagnetostrictive vibratory device for cavitation erosion. The results show that the cavitation erosion resistance ofthe as-welded Cu12Mn8Al3Fe2Ni alloy is much more superior to that of the as-cast one. The cumulative mass lossand the mass loss rate of the as-welded Cu12Mn8Al3Fe2Ni alloy are almost 1/4 that of the as-cast one. SEM analysisof eroded specimens reveals that the as-cast Cu12Mn8Al3Fe2Ni alloy is attacked more severely than the as-weldedone. Microcracks causing cavitation damage initiate at the phase boundaries.
文摘A new isopolyoxovanadate [Ni(1,10′-phen) 3] 2 [V Ⅳ 2V Ⅴ 8O 26] was hydrothermally synthesized and structurally characterized by the single crystal X-ray diffraction. The compound crystallizes in orthorhombic system, space group Pbcn with a=1.362 9(3) nm, b=2.215 6(4) nm, c= 2.571 2(4) nm, V=7.764(2) nm 3, Z=4, R=0.040 3, wR 2=0.044 6. The compound exhibits an unusual empty ellipsoidal cage, which is constructed by eight {V ⅤO 4} tetrahedra and two {V ⅣO 5} square pyramids via corner-sharing modes. The chiral [Ni(1,10′-phen) 3] 2+ complexes act as the counter cations.
