基于MPS-FEM耦合方法对比研究刚性与弹性挡板对液舱晃荡的抑制作用（英文）

由流体冲击载荷引起的流固耦合问题广泛存在于船舶与海洋工程领域.例如:在特定激励频率下载液货舱内流体的非线性运动引起对舱壁的砰击作用,进而可能影响液舱围护系统的安全性.由于此类流固耦合问题通常涉及多学科知识,且流体自由面的变化具有强非线性特征,对研究人员带来较大挑战.考虑到Lagrange类方法在处理结构和流体自由面大变形问题上的优势,基于MPS-FEM耦合方法开发了流固耦合求解器.其中,采用MPS方法来数值模拟流体场瞬态变化,FEM方法来分析结构场的变形问题.此外,该求解器采用了弱耦合的方式来实现流体场和结构场之间的数据传递.为了验证该方法在处理流固耦合问题上的可靠性,首先数值研究了溃坝泄洪流与弹性挡板之间的流固耦合标准算例,数值结果与实验标准结果能够较好地吻合.此后,采用该求解器数值研究了带刚性挡板和弹性挡板的液舱晃荡问题,对比分析了多种激励频率下两种挡板对液舱内流体运动及舱壁上冲击压力的抑制效果.

Numerical Simulation of Sloshing with Large Deforming Free Surface by MPS-LES Method

Moving particle semi-implicit （MPS） method is a fully Lagrangian particle method which can easily solve problems with violent free surface. Although it has demonstrated its advantage in ocean engineering applications, it still has some defects to be improved. In this paper, MPS method is extended to the large eddy simulation （LES） by coupling with a sub-particle-scale （SPS） turbulence model. The SPS turbulence model turns into the Reynolds stress terms in the filtered momentum equation, and the Smagorinsky model is introduced to describe the Reynolds stress terms. Although MPS method has the advantage in the simulation of the free surface flow, a lot of non-free surface particles are treated as free surface particles in the original MPS model. In this paper, we use a new free surface tracing method and the key point is ＂neighbor particle＂. In this new method, the zone around each particle is divided into eight parts, and the particle will be treated as a free surface particle as long as there are no ＂neighbor particles＂ in any two parts of the zone. As the number density parameter judging method has a high efficiency for the free surface particles tracing, we combine it with the neighbor detected method. First, we select out the particles which may be mistreated with high probabilities by using the number density parameter judging method. And then we deal with these particles with the neighbor detected method. By doing this, the new mixed free surface tracing method can reduce the mistreatment problem efficiently. The serious pressure fluctuation is an obvious defect in MPS method, and therefore an area-time average technique is used in this paper to remove the pressure fluctuation with a quite good result. With these improvements, the modified MPS-LES method is applied to simulate liquid sloshing problems with large deforming free surface. Results show that the modified MPS-LES method can simulate the large deforming free surface easily. It can not only capture the large impact pressure accurately on rolling tank wall but also can generate all physical phenomena successfully. The good agreement between numerical and experimental results proves that the modified MPS-LES method is a good CFD methodology in free surface flow simulations.

Preventive Effects of Five Drugs on Mycoplasma Pneumonia of Swine (MPS)

The paper was to explore the preventive effects of five drugs on mycoplasma pneumonia of swine （MPS） and to provide reference for clinical medication of pig farms in Hainan Province. A total of 444 health piglets were randomly divided into 6 groups, including five medication groups （72 piglets in group A, 74 pig- lets in group B, 72 piglets in group C, 76 piglets in group D, 76 piglets in group E） and one control group （74 piglets）. The piglets in experimental groups were treated drugs once a day for successive 5 days at 30, 60, 90, 120 and 150 of age. The piglets in control group were free of medication. At 70 and 140 days of age, 15 piglets of each group were randomly selected to collect their blood sermn. The Mycoplasma hyopneumoniae （M-Hyo） antibodies in serum were measured by en- zyme-linked immunosorbent assay （ELISA）. During the experiment, the incidence rates of respiratory disease, lung lesion, feed conversion rate, average daily gain （ADG）, and mortality rate of pigs were also observed and recorded. The results showed that the five drugs had significant difference in preventative effects. Group C （Zhiyuanjing group） received the best preventive effect and the highest economic benefits. Compared with control group, the ADG and feed conversion rate in group C were increased by 7.53% and 9.09%, respectively; the incidence rate of respiratory disease was reduced by 13.44% and lung lesion was alleviated by 81.43% ; and the earnings of each pig could rise by 132.70 yuan. The preventative effect and economic benefit of the drugs was sequenced by Chansu Kechuanling and Bingchan Kechuanwang. Wante Feilin and amoxicillin had weaker preventive effects against MPS but greatly influenced growth performance of pigs, so they should be used alternatively with other drugs.

Impacts of Diurnal Variation of Mountain-plain Solenoid Circulations on Precipitation and Vortices East of the Tibetan Plateau during the Mei-yu Season

Diurnal variations of two mountain-plain solenoid （MPS） circulations associated with ＂first-step＂ terrain [Tibetan Plateau （TP）] and ＂second-step＂ terrain （high mountains between the TP and ＂east plains＂） in China and their influence on the south west vortex （SWV） and the mei-yu front vortex （MYFV） were investigated via a semi-idealized mesoscale numerical model [Weather Research and Forecasting （WRF）] simulation integrated with ten-day average fields （mei-yu period of 1-10 July 2007）. The simulations successfully reproduced two MPS circulations related to first and second-step terrain, diurnal vari- ations from the eastern edge of the TP to the Yangtze River-Huaihe River valleys （YHRV）, and two precipitation maximum centers related to the SWV, MYFV. Analyses of the averaged final seven-day simulation showed the different diurnal peaks of precipitation at different regions： from the aftemoon to early evening at the eastern edge of the TP; in the early evening to the next early morning in the Sichuan Basin （SCB）; and in the late evening to the next early morning over the mei-yu front （MYF）. Analyses of individual two-day cases confirmed that the upward branches of the nightlime MPS circulations enhanced the precipitation over the SWV and the MYFV and revealed that the eastward extension of the SWV and its con vection were conducive to triggering the MYFVs. The eastward propagation of a rainfall streak from the eastern edge of the TP to the eastern coastal region was primarily due to a series of convective activities of several systems from west to east, including the MPS between the TP and SCB, the SWV, the MPS between second-step terrain and tile east plains, and the MYFV.

Moving-Particle Semi-Implicit Method for Vortex Patterns and Roll Damping of 2D Ship Sections

A meshless method, Moving-Particle Semi-hnplicit Method （MPS） is presented in this paper to simulate the rolling of different 2D ship sections. Sections S. S. 0.5, S.S. 5.0 and S. S. 7.0 of series 60 with CB = 0.6 are chosen for the simulation. It shows that the result of MPS is very close to results of experiments or mesh-numerical simulations. In the simulation of MPS, vortices are found periodically in bilges of ship sections. In section S. S. 5.0 and section S. S. 7.0, which are close to the middle ship, two little vortices are found at different bilges of the section, in section S. S. 0.5, which is close to the bow, only one big vortex is found at the bottom of the section, these vortices patterns are consistent with the theory of Ikeda. The distribution of shear stress and pressure on the rolling hull of ship section is calculated. When vortices are in bilges of the section, the sign clmnge of pressure can be found, but in section S. S. 0.5, there is no sign change of pressure because only one vortex in the bottom of the section. With shear stress distribution, it can be found the shear stress in bilges is bigger than that at other part of the ship section. As the free surface is considered, the shear stress of both sides near the free surface is close to zero and even sign changed.

Assessment of toxicity potential of metallic elements in discarded electronics:A case study of mobile phones in China

The electronic waste (e-waste) is increasingly flooding Asia,especially China.E-waste could precipitate a growing volume of toxic input to the local environment if it was not handed properly.This makes the evaluation of environmental impact from electronics an essentially important task for the life cycle assessment (LCA) and the end-of-life management of electronic products.This study presented a quantitative investigation on the environmental performance of typical electronics.Two types of disposed mobile...

Multi-scale morphology analysis of acoustic emission signal and quantitative diagnosis for bearing fault

Monitoring of potential bearing faults in operation is of critical importance to safe operation of high speed trains.One of the major challenges is how to differentiate relevant signals to operational conditions of bearings from noises emitted from the surrounding environment.In this work,we report a procedure for analyzing acoustic emission signals collected from rolling bearings for diagnosis of bearing health conditions by examining their morphological pattern spectrum（MPS） through a multi-scale morphology analysis procedure.The results show that acoustic emission signals resulted from a given type of bearing faults share rather similar MPS curves.Further examinations in terms of sample entropy and Lempel-Ziv complexity of MPS curves suggest that these two parameters can be utilized to determine damage modes.

Frequency and voltage-dependent electrical and dielectric properties of Al/Co-doped PVA/p-Si structures at room temperature

In order to investigate of cobalt-doped interracial polyvinyl alcohol （PVA） layer and interface trap （Dit） effects, A1/p- Si Schottky barrier diodes （SBDs） are fabricated, and their electrical and dielectric properties are investigated at room temperature. The forward and reverse admittance measurements are carded out in the frequency and voltage ranges of 30 kHz-300 kHz and -5 V-6 V, respectively. C-V or er-V plots exhibit two distinct peaks corresponding to inversion and accumulation regions. The first peak is attributed to the existence of Dit, the other to the series resistance （Rs）, and interfacial layer. Both the real and imaginary parts of dielectric constant （er and err） and electric modulus （Mr and Mrr）, loss tangent （tan~）, and AC electrical conductivity （aac） are investigated, each as a function of frequency and applied bias voltage. Each of the M~ versus V and Mrr versus V plots shows a peak and the magnitude of peak increases with the increasing of frequency. Especially due to the Dit and interfacial PVA layer, both capacitance （C） and conductance （G/w） values are strongly affected, which consequently contributes to deviation from both the electrical and dielectric properties of A1/Co-doped PVA/p-Si （MPS） type SBD. In addition, the voltage-dependent profile of Dit is obtained from the low-high frequency capacitance （CLF-CHF） method.

Comparative study of MPS method and level-set method for sloshing flows

This paper presents a comparative study of a meshless level-set method in the simulation of sloshing flows. The numerical moving particle semi-implicit （MPS） method and a grid based schemes of the MPS and level-set methods are outlined and two violent sloshing cases are considered. The computed results are compared with the corresponding experimental data for validation. The impact pressure and the deformations of free surface induced by sloshing are comparatively analyzed, and are in good agreement with experimental ones. Results show that both the MPS and level-set methods are good tools for simulation of violent sloshing flows. However, the second pressure peaks as well as breaking and splashing of free surface by the MPS method are captured better than by the level-set method.

Numerical study of the wave-induced slamming force on the elastic plate based on MPS-FEM coupled method

Slamming is the phenomenon of structure impacting the water surface. It always results in the extremely high load on the structure. This paper is mainly concerned with the slamming force caused by the wave-plate interaction. In this paper, the process of solitary wave impacting onto the horizontal plate is simulated with the help of the moving particle semi-implicit and finite element coupled method（MPS-FEM）. The MPS method is adopted to calculate the fluid domain while the structural domain is solved by FEM method. In the first series of simulations, the profiles of the solitary waves with various amplitudes, which are generated in the numerical wave tank, are compared with the theoretical results. Thereafter the interaction between the solitary waves and a rigid plate is simulated. The effects of wave amplitude, as well as the elevation of the plate above the initial water level, on the slamming force are numerically investigated. The calculated results are compared with the available experimental data. Finally, the interactions between the solitary waves and the elastic plate are also simulated. The effects of the structural flexibility on the wave-induced force are analyzed by the comparison between the cases with elastic and the rigid plate.

Numerical simulation of 3-D free surface flows by overlapping MPS

An overlapping moving particle semi-implicit （MPS） method is applied for 3-D free surface flows based on our in-house particle solver MLParticle-SJTU. In this method, the coarse particles are distributed in the whole domain and the fine particles are distributed in the local region of interest at the same time. With the fine particles being generated and removed dynamically, an algorithm of generating particles based on the 3-D overlapping volume is developed. Then, a 3-D dam break flow with an obstacle is simulated to validate the overlapping MPS. The qualitative comparison among experimental data and the results obtained by the VOF and the MPS shows that the shape of the free surface obtained by the overlapping MPS is more accurate than that obtained by the UNI-coarse and close to that obtained by the UNI-fine in the overlapping domain. In addition, the water height and the impact pressure at Pi are also in an overall agreement with experimental data. Finally, the CPU time required by the overlapping MPS is about half of that required by the UNl-fine.

Entanglement property in matrix product spin systems

We study the entanglement property in matrix product spin-ring systems systemically by von Neumann entropy. We find that： （i） the Hilbert space dimension of one spin determines the upper limit of the maximal value of the entanglement entropy of one spin, while for multiparticle entanglement entropy, the upper limit of the maximal value depends on the dimension of the representation matrices. Based on the theory, we can realize the maximum of the entanglement entropy of any spin block by choosing the appropriate control parameter values. （ii） When the entanglement entropy of one spin takes its maximal value, the entanglement entropy of an asymptotically large spin block, i.e. the renormalization group fixed point, is not likely to take its maximal value, and so only the entanglement entropy Sn of a spin block that varies with size n can fully characterize the spin-ring entanglement feature. Finally, we give the entanglement dynamics, i.e. the Hamiltonian of the matrix product system.

Modeling of single film bubble and numerical study of the plateau structure in foam system

The single-film bubble has a special geometry with a certain amount of gas shrouded by a thin layer of liquid film under the surface tension force both on the inside and outside surfaces of the bubble. Based on the mesh-less moving particle semi-implicit（MPS） method, a single-film double-gas-liquid-interface surface tension（SDST） model is established for the single-film bubble,which characteristically has totally two gas-liquid interfaces on both sides of the film. Within this framework, the conventional surface free energy surface tension model is improved by using a higher order potential energy equation between particles, and the modification results in higher accuracy and better symmetry properties. The complex interface movement in the oscillation process of the single-film bubble is numerically captured, as well as typical flow phenomena and deformation characteristics of the liquid film.In addition, the basic behaviors of the coalescence and connection process between two and even three single-film bubbles are studied, and the cases with bubbles of different sizes are also included. Furthermore, the classic plateau structure in the foam system is reproduced and numerically proved to be in the steady state for multi-bubble connections.