Multi-scale Modeling and Finite Element Analyses of Thermal Conductivity of 3D C/SiC Composites Fabricating by Flexible-Oriented Woven Process

Thermal conductivity is one of the most significant criterion of three-dimensional carbon fiber-reinforced SiC matrix composites(3D C/SiC).Represent volume element(RVE)models of microscale,void/matrix and mesoscale proposed in this work are used to simulate the thermal conductivity behaviors of the 3D C/SiC composites.An entirely new process is introduced to weave the preform with three-dimensional orthogonal architecture.The 3D steady-state analysis step is created for assessing the thermal conductivity behaviors of the composites by applying periodic temperature boundary conditions.Three RVE models of cuboid,hexagonal and fiber random distribution are respectively developed to comparatively study the influence of fiber package pattern on the thermal conductivities at the microscale.Besides,the effect of void morphology on the thermal conductivity of the matrix is analyzed by the void/matrix models.The prediction results at the mesoscale correspond closely to the experimental values.The effect of the porosities and fiber volume fractions on the thermal conductivities is also taken into consideration.The multi-scale models mentioned in this paper can be used to predict the thermal conductivity behaviors of other composites with complex structures.

Tensile Mechanical Behavior and Failure Mechanism of a Plain-Woven SiCf/SiC Composites at Room and Elevated Temperatures

Ceramic matrix composites (CMCs) are the preferred materials for solving advanced aerospace high-temperature structural components;it has the comprehensive advantages of higher temperature (~1500˚C) and low density. In service environments, CMCs exhibit complex damage mechanisms and failure modes, which are affected by constituent materials, meso-architecture and inhere defects. In this paper, the in-plane tensile mechanical behavior of a plain-woven SiCf/SiC composite at room and elevated temperatures was investigated, and the factors affecting the tensile strength of the material were discussed in depth. The results show that the tensile modulus and strength of SiCf/SiC composites at high temperature are lower, but the fracture strain increases and the toughness of the composites is enhanced;the stitching holes significantly weaken the tensile strength of the material, resulting in the material is easy to break at the cross-section with stitching holes.

Electromagnetic wave absorption and mechanical properties of SiC nanowire/low-melting-point glass composites sintered at 580°C in air

Si C nanowires are excellent high-temperature electromagnetic wave (EMW) absorbing materials. However, their polymer matrix composites are difficult to work at temperatures above 300℃, while their ceramic matrix composites must be prepared above 1000℃ in an inert atmosphere. Thus, for addressing the abovementioned problems, SiC/low-melting-point glass composites were well designed and prepared at 580℃ in an air atmosphere. Based on the X-ray diffraction results, SiC nanowires were not oxidized during air atmosphere sintering because of the low sintering temperature. Additionally, SiC nanowires were uniformly distributed in the glass matrix material. The composites exhibited good mechanical and EMW absorption properties. As the filling ratio of SiC nanowires increased from 5wt%to 20wt%, the Vickers hardness and flexural strength of the composite reached HV 564 and 213 MPa, which were improved by 27.7%and 72.8%, respectively, compared with the low-melting-point glass. Meanwhile, the dielectric loss and EMW absorption ability of SiC nanowires at 8.2–12.4 GHz were also gradually improved. The dielectric loss ability of low-melting-point glass was close to 0. However, when the filling ratio of SiC nanowires was 20wt%, the composite showed a minimum reflection loss (RL) of-20.2 dB and an effective absorption (RL≤-10 dB) bandwidth of2.3 GHz at an absorber layer thickness of 2.3 mm. The synergistic effect of polarization loss and conductivity loss in SiC nanowires was responsible for this improvement.

Damping performance of SiC nanoparticles reinforced magnesium matrix composites processed by cyclic extrusion and compression

This work dealt with the damping performance and its underlying mechanism in SiC nanoparticles reinforced AZ91D composite(SiC_(np)/AZ91D)processed by cyclic extrusion and compression(CEC).It was found that the CEC process significantly affects the damping performance of the composite due to alterations in the density of dislocations and grain boundaries in the matrix alloy.Although there would be dynamic precipitation of the Mg17Al12 phase during processing which increases the phase interface and limits the mobility of dislocations and grain boundaries.The results also showed that the damping capacity of 1%SiC_(np)/AZ91D composite continuously decreases with adding CEC pass number and it consistently increases with rising the applied temperature.Considering the first derivative of the tanδ-T curve,the dominant damping mechanism based on test temperature can be divided into three regions.These three regions are as follows(i)dislocation vibration of the weak pinning points(≤T_(cr)),(ii)dislocation vibration of the strong pinning points(T_(cr)∼T_(V)),and(iii)grain boundary/interface sliding(≥T_(V))

Effects of Co_(2)O_(3)Addition on Microstructure and Properties of SiC Composite Ceramics for Solar Absorber and Storage

SiC composite ceramics for solar absorber and storage integration are new concentrating solar power materials.SiC composite ceramics for solar absorber and storage integration were fabricated using SiC,black corundum and kaolin as the raw materials,Co_(2)O_(3)as the additive via pressureless graphite-buried sintering method in this study.Influences of Co_(2)O_(3)on the microstructure and properties of SiC composite ceramics for solar absorber and storage integration were studied.The results indicate that sample D2(5wt%Co_(2)O_(3))sintered at 1480℃exhibits optimal performances for 119.91 MPa bending strength,93%solar absorption,981.5 kJ/kg(25-800℃)thermal storage density.The weight gain ratio is 12.58 mg/cm2after 100 h oxidation at 1000℃.The Co_(2)O_(3)can decrease the liquid phase formation temperature and reduce the viscosity of liquid phase during sintering.The liquid with low viscosity not only promotes the elimination of pores to achieve densification,but also increases bending strength,solar absorption,thermal storage density and oxidation resistance.A dense SiO_(2) layer was formed on the surface of SiC after 100 h oxidation at 1000℃,which protects the sample from further oxidation.However,excessive Co_(2)O_(3)will make the microstructure loose,which is disadvantageous to the performances of samples.

SiC/SiC复合材料层板低速冲击及其剩余强度试验研究

高速飞行器中的陶瓷基复合材料结构在服役过程中不可避免地会遇到低速冲击问题,低速冲击后的损伤形式以及剩余承载能力是影响飞行器结构安全的关键问题。本研究以二维编织SiC/SiC复合材料板件为研究对象,在不同能量下开展了低速冲击试验,分析了低速冲击载荷下试验件的表面损伤状态,通过计算机断层扫描技术观察了试验件内部的损伤形貌,结合冲击过程中的冲击响应曲线以及应变历史曲线,分析了SiC/SiC复合材料低速冲击过程的损伤机理。针对含勉强目视可见损伤的试验件开展了冲击后剩余强度试验,研究了勉强目视可见损伤对SiC/SiC复合材料剩余承载性能的影响。结果表明,在低速冲击载荷的作用下,试验件的表面损伤主要包括无表面损伤、勉强目视可见损伤、半穿透损伤以及穿透损伤,试验件的内部损伤主要有锥形体裂纹、纱线断裂以及分层损伤。低速冲击损伤会严重影响SiC/SiC复合材料的剩余性能,虽然试验件损伤勉强目视可见,但其剩余压缩强度为无损件81%,剩余拉伸强度仅为无损件的68%。

SiC_(f)/Ti65复合材料的拉伸行为研究

采用磁控溅射先驱丝法结合热等静压工艺制备SiC_(f)/Ti65复合材料,研究了SiC_(f)/Ti65复合材料室温、高温拉伸行为,揭示了SiC_(f)/Ti65复合材料拉伸断裂机制。研究结果表明:SiC_(f)/Ti65复合材料的室温、高温抗拉强度相比于Ti65合金的抗拉强度分别提升29%和164%,验证了复合材料的增强效果。SiC_(f)/Ti65复合材料的室温拉伸断裂机制为反应层断裂、纤维/基体界面脱粘、基体脆性断裂、纤维断裂、包套韧性断裂;高温断裂机制为反应层断裂、纤维/基体界面脱粘、纤维断裂、W/SiC界面脱粘、基体和包套韧性断裂。

Ti预处理的SiC_(f)/SiC与镍基高温合金复合铸件的界面组织与强度

由SiC_(f)/SiC复合材料与K403镍基高温合金熔体制备的一体化铸件,冷却到室温时会出现自行断裂。通过采用Ti粉埋覆包渗工艺在1100℃下对SiC_(f)/SiC表面进行预处理,并在适当工艺下与K403镍基高温合金熔体进行陶瓷型精密铸造,成功实现SiC_(f)/SiC与K403镍基高温合金的一体化成形和界面的牢固结合。结果表明:Ti预处理层平均厚度为17μm左右,Ti向SiC_(f)/SiC渗透、扩散和反应,形成含TiC,Ti3SiC2,Ti5Si3Cx,SiC相的显微组织;经过与高温镍基金属液复合铸造后,预处理层演变成厚约120μm的界面反应层,其典型界面组织为Ni2Si+C+Al4C3+MC(M主要含Ti及少量的Cr,Mo,W)。预处理层的存在减轻Ni与SiC的有害石墨化反应,缓解高温金属液对SiC_(f)/SiC的热冲击,形成的界面反应层降低热膨胀系数失配造成的热应力,使得SiC_(f)/SiC与K403一体化铸件结合界面的室温剪切强度达到63.5 MPa。

Effect of SiC whiskers on the oxidation protective properties of SiC coatings for carbon/carbon composites

In order to effectively employ the unique high temperature mechanical properties of carbon/carbon composite substrates, SiC coatings reinforced by SiC whiskers were prepared by pack cementation method. The effect of SiC whiskers on the oxidation resistance properties of the single-layer coating and double-layer coating was investigated. SiC whiskers in the single-layer SiC coating have little effect on the anti-oxidation property but obviously improve the thermal shock property. The double-layer coating with inner-layer reinforced coating exhibits more perfect anti-oxidation ability than the double-layer coating with SiC inner-layer coating.

Compression Creep Behavior of High Volume Fraction of SiC Particles Reinforced Al Composite Fabricated by Pressureless Infiltration

The compression creep deformation of the high volume fraction of SiC particles reinforced AI-Mg-Si composite fabricated by pressure-less infiltration was investigated. The experimental results show that the creep stress exponents are very high at temperatures of 673 K, 723 K and 773 K, and if taking the threshold stress into account, the true stress exponent of minimum creep strain rate is still approximately 5, although the volume fraction of reinforcements is very high. The creep strain rate in the high volume fraction reinforced aluminum alloy matrix composites is controlled by matrix lattice diffusion. It is found that the creep-strengthening effect of high volume fraction of silicon carbide particles is significant, although the particles do not form effective obstacles to dislocation motion.

MICROSTRUCTURE OF ELECTRODEPOSITED Ni-W-P-SiC COMPOSITE COATINGS

ＭＩＣＲＯＳＴＲＵＣＴＵＲＥＯＦＥＬＥＣＴＲＯＤＥＰＯＳＩＴＥＤＮｉＷＰＳｉＣＣＯＭＰＯＳＩＴＥＣＯＡＴＩＮＧＳ①ＧｕｏＺｈｏｎｇｃｈｅｎｇ，ＹａｎｇＸｉａｎｗａｎ，ＬｉｕＨｏｎｇｋａｎｇＤｅｐａｒｔｍｅｎｔｏｆＭｅｔａｌｕｒｇｙ，Ｋｕｎｍｉｎ...

New Iron-based SiC Spherical Composite Magnetic Abrasive for Magnetic Abrasive Finishing

SiC magnetic abrasive is used to polish surfaces of precise, complex parts which are hard, brittle and highly corrosion-resistant in magnetic abrasive finishing（MAF）. Various techniques are employed to produce this magnetic abrasive, but few can meet production demands because they are usually time-consuming, complex with high cost, and the magnetic abrasives made by these techniques have irregular shape and low bonding strength that result in low processing efficiency and shorter service life. Therefore, an attempt is made by combining gas atomization and rapid solidification to fabricate a new iron-based SiC spherical composite magnetic abrasive. The experimental system to prepare this new magnetic abrasive is constructed according to the characteristics of gas atomization and rapid solidification process and the performance requirements of magnetic abrasive. The new iron-based SiC spherical composite magnetic abrasive is prepared successfully when the machining parameters and the composition proportion of the raw materials are controlled properly. Its morphology, microstructure, phase composition are characterized by scanning electron microscope（SEM） and X-ray diffraction（XRD） analysis. The MAF tests on plate of mold steel S136 are carried out without grinding lubricant to assess the finishing performance and service life of this new SiC magnetic abrasive. The surface roughness（Ra） of the plate worked is rapidly reduced to 0.051 μm from an initial value of 0.372 μm within 5 min. The MAF test is carried on to find that the service life of this new SiC magnetic abrasive reaches to 155 min. The results indicate that this process presented is feasible to prepare the new SiC magnetic abrasive; and compared with previous magnetic abrasives, the new SiC spherical composite magnetic abrasive has excellent finishing performance, high processing efficiency and longer service life. The presented method to fabricate magnetic abrasive through gas atomization and rapid solidification presented can significantly improve the finishing performance and service life of magnetic abrasive, and provide a more practical approach for large-scale industrial production of magnetic abrasive.

Particle Removal Mechanism of High Volume Fraction SiCp/Al Composites by Single Diamond Grit Tool

Particle removal mechanism was presented during machining particle SiC/Al composites with diamond grinding tool. The relevant removal modes and their mechanisms were discussed considering the impact and squeezing effect of diamond grit on the SiC particle. The experimental results show that the aluminum matrix has larger plastic deformation, so the aluminum mixed with the surplus SiC particles is cut from the surface. The SiC particles can be removed in multiple ways, such as broken/fractured, micro cracks, shearing and pulled out, etc. More particles removed by shearing, and less particles removed by fractured during material removal progress can produce a better machined surface.

环境温度对二维编织SiC/SiC复合材料拉伸性能的影响研究

为了研究环境温度对陶瓷基复合材料拉伸性能的影响,在室温和800℃,1000℃,1200℃惰性气体保护环境下开展了二维编织SiC/SiC复合材料的拉伸试验。采用数字图像相关技术采集了高温环境下试件的变形数据。通过光学显微镜和扫描电子显微镜拍摄了试件的断口形貌。结果表明:800~1200℃内,二维编织SiC/SiC复合材料的拉伸应力-应变响应同样具有明显的双线性特征,初始线性段的弹性模量与室温测试结果相近,高温环境下第二线性段弹性模量低于室温环境;800~1200℃惰性气体环境下材料拉伸强度较室温环境低20%左右;温度主要影响材料中纤维与基体的结合状态和SiC纤维的强度。一方面,温度越高断口纤维拔出情况越严重;另一方面,温度越高SiC纤维强度越低,二维编织SiC/SiC复合材料强度也有所下降。

Corrosion resistance of electrodeposited RE-Ni-W-P-SiC composite coating

Immersion experiment results show that corrosion rate of the as deposited RE Ni W P SiC composite coating in HCl solutions increases with the rise of HCl concentration. On the contrary, the corrosion rate of the composite coating after heat treatment decreases with increasing HCl concentration. The corrosion rates of the composite coatings in as deposited state and after heat treatment in H 2SO 4 and H 3PO 4 solutions respectively decrease with the rise of H 2SO 4 and H 3PO 4 concentrations. The corrosion rate of the composite coating as deposited in FeCl 3 solutions decreases with increasing FeCl 3 concentration, while the rate of the composite coating after heat treatment increases with the rise of FeCl 3 concentration. The corrosion rate of 316L stainless steel in the corrosion media of H 2SO 4, HCl, H 3PO 4 and FeCl 3 solutions at different concentrations increases with rising concentration. In addition, the corrosion rate of 316L stainless steel in the corrosion media of H 2SO 4, HCl, H 3PO 4 and FeCl 3 solutions respectively is much greater than that of the RE Ni W P SiC composite coating as deposited and after heat treatment in the same corrosion media. [

Effect of SiC particle addition on microstructure of Mg_2Si/Al composite

In the present study, by adding SiC particles into Al-Si-Mg melt, Mg2Si and SiC particles hybrid reinforced Al matrix composites were fabricated through the Mg2Si in situ synthesis in melt combined with the SiC ex situ stir casting. The as-cast microstructure containing primary Mg2Si and SiC particles that distribute homogenously in Al matrix was successfully achieved. The effects of SiC particle addition on the microstructure of Mg2Si/Al composites were investigated by using scanning electron microscopy(SEM) and XRD. The results show that, with increasing the fraction of the SiC particles from 5wt.% to 10wt.%, the morphologies of the primary Mg2Si particulates in the prepared samples remain polygonal, but the size of the primary phase decreases slightly. However, when the SiC particle addition reaches 15wt.%, the morphologies of the primary Mg2Si particulates change partially from polygonal to quadrangular with a decrease in size from 50 μm to 30 μm. The size of primary Al dendrites decreases with increasing fraction of the SiC particles from 0wt.% to 15wt.%. The morphology of the eutectic Mg2Si phase changes from a fi ber-form to a short fi ber-form and/or a dot-like shape with increasing fraction of the SiC particles. Furthermore, no signifi cant change in dendrite arm spacing(DAS) was observed in the presence of SiC particles.

Microstructure and mechanical properties of SiC-particle-strengthening tri-metal Al/Cu/Ni composite produced by accumulative roll bonding process

In this study, a multilayer Al/Ni/Cu composite reinforced with Si C particles was produced using an accumulative roll bonding(ARB) process with different cycles. The microstructure and mechanical properties of this composite were investigated using optical and scanning microscopy and hardness and tensile testing. The results show that by increasing the applied strain, the Al/Ni/Cu multilayer composite converted from layer features to near a particle-strengthening characteristic. After the fifth ARB cycle, a composite with a uniform distribution of reinforcements(Cu, Ni, and SiC) was fabricated. The tensile strength of the composite increased from the initial sandwich structure to the first ARB cycle and then decreased from the first to the third ARB cycle. Upon reaching five ARB cycles, the tensile strength of the composite increased again. The variation in the elongation of the composite exhibited a tendency similar to that of its tensile strength. It is observed that with increasing strain, the microhardness values of the Al, Cu, and Ni layers increased, and that the dominant fracture mechanisms of Al and Cu were dimple formation and ductile fracture. In contrast, brittle fracture in specific plains was the main characteristic of Ni fractures.

Effects of addition of rare earth on properties and structures of Ni-W-B-SiC composite coatings

The effects of rare earth (RE) on the composition, phase structures, surface morphologies and hardness of electrodeposited RE Ni W B SiC composite coatings were discussed. The results show that W and SiC contents in the coatings increase with the increase of RE in the bath. When RE is added in the coatings, the grains are refined and the trend of formation of amorphous coatings is increased. Moreover, the thermal stability of the RE Ni W B SiC composite coatings is enhanced. The hardness of the coatings is increased with the increase of heat treatment temperature, and it reaches the peak value when heated at 400 ℃. Besides, the hardness of the RE Ni W B SiC coatings is higher than that of the Ni W B SiC coatings.

STUDIES ON MICROYIELD BEHAVIOR OF A SiCp/2024Al COMPOSITE

１ＩＮＴＲＯＤＵＣＴＩＯＮＤｕｅｔｏｔｈｅｅｘｃｅｌｅｎｔｃｏｍｐｒｅｈｅｎｓｉｖｅｐｒｏｐｅｒｔｉｅｓｓｕｃｈａｓｈｉｇｈｓｐｅｃｉｆｉｃｓｔｒｅｎｇｔｈａｎｄＹｏｕｎｇ’ｓｍｏｄｕｌｕｓ，ｌｏｗｅｒｔｈｅｒｍａｌｃｏｎｄｕｃｔｉｖｉｔｙａｎｄｔ...