HER2-low status improves prognosis prediction in breast cancer patients receiving neoadjuvant treatment:A comparison of pathological stage,modified CPS+EG scoring system,and Neo-Bioscore

Objective:To explore the prognosis-predictive influence of human epidermal growth factor receptor 2(HER2)-low status in breast cancer patients after neoadjuvant therapy(NAT).Methods:Consecutive patients with invasive breast cancer who underwent NAT and surgery from January 2009 to December 2020 at multiple centers were included.A modified CPS+EG scoring system that integrates HER2-low status,CPS+EGH_(low)was developed.Multiple scoring systems were compared via receiver operating characteristic curves with the area under curve(AUC),the Akaike information criterion,the C-index,and calibration curves.Results:A total of 2,141 patients were included:1,074,640,and 427 patients in the training,internal validation,and external validation groups,respectively.HER2-low patients had a significantly better breast cancer-specific survival(BCSS,P=0.008)and recurrence-free interval(RFI,P=0.030)compared to HER2-zero patients(P=0.038)but inferior outcomes than HER2-amplified ones(BCSS,P=0.002;RFI,P<0.001).The CPS+EGH_(low)(AUC:0.846,0.817,0.901)could stratify patients according to BCSS in training,internal validation,and external validation group,respectively,overperforming pathological stage(PS)(AUC:0.746,0.779,0.754),CPS+EG(AUC:0.771,0.752,0.748),and Neo-Bioscore(AUC:0.783,0.777,0.786,all P<0.05).Conclusions:HER2-low status showed a significant prognostic value in breast cancer patients after NAT.The CPS+EGH_(low)model significantly outperformed PS,CPS+EG,and Neo-Bioscore in clinical outcome prediction,which may guide further therapy targeting HER2-low.

SBIRS-low卫星红外探测系统探测距离分析

计算了SBIRS low卫星与弹头之间的空间距离及其星载红外探测器对弹头的最大理想探测距离,阐明了降低弹头表面温度以对抗(SBIRS low)卫星的有效性。

A Bionic Fish Cilia Median-Low Frequency Three-Dimensional Piezoresistive MEMS Vector Hydrophone

A bionic fish cilia median-low frequency three-dimensional MEMS vector hydrophone is reported in this paper. The piezoresistive reasonable position was obtained through finite element analysis by ANSYS and the structure was formed by MEMS processes including lithography, ion implantation, PECVD and etching,etc. The standing wave barrel results show that the lowest sensitivity of the hydrophone is-200 d B and reach up to-160 d B(in which the voltage amplification factor is 300). It has a good frequency response characteristics in 25 Hz ～ 1500 Hz band. Directivity tests displayed that the hydrophone has a good "8"-shaped directivity,in which the resolution is not less than 30 d B, and asymmetry of the maximum axial sensitivity value is less than 1.2 d B.

Correlation of Deactivation of Ni-Mo-W/Al2O3 during Ultra-Low-Sulfur Diesel Production with Surface Carbon Species

The deactivation of a Ni-Mo-W/Al_2O_3 catalyst during ultra-low-sulfur diesel production was investigated in a pilot plant. The reasons of catalyst deactivation were analyzed by the methods of elemental analysis, BET and TG-MS. The results showed that the catalyst deactivation rate was notable at the beginning of run, and then gradually reached a steady state after 448 h. In the initial period the catalyst deactivation may mainly be caused by the formation of the carbon deposits. The carbon deposits blocked the catalyst pores and the accessibility of active center decreased. The TG-MS analysis identified three types of carbon species deposited on the catalysts, viz.: the low temperature carbon deposit with high H/C atomic ratio, the medium temperature carbon deposit, and the high temperature carbon with low H/C atomic ratio. The amount of high temperature carbon deposits on the catalyst determined the overall activity and, therefore the high temperature carbon was a major contributor to the deactivation of Ni-Mo-W catalyst.

Experimental Research on Refining Slag Systems Containing BaO for Ultra-Low Sulphur Steel

The experimental research on refining slag systems for ultra-low sulphur steel was carried out in a 10 kg induction furnace.It was proved that sulphur element in molten steel can be removed to less than 5×10^(-6) by adding CaO-Al_2O_3-SiO_2-MgO-CaF_2 slag on the surface of molten steel and feeding CaO-BaO-CaF2 wire into molten steel.And L_s,which is the coefficient of sulphur between slag and molten steel,that is ω(s)/ω[s],increases by increasing I(I = ωBaO/ωCaO).When I=5/3,L_s can be up to its maximum of 633.The CaSi is effective for deep desulphurization,especially when it is added to the slag of wire feeding.

Novel mechanism for the modification of Al_2O_3-based inclusions in ultra-low carbon Al-killed steel considering the effects of magnesium and calcium

Many researchers have explored the inclusion modification mechanism to improve non-metallic inclusion modifications in steelmaking. In this study, two types of industrial trials on inclusion modifications in liquid steel were conducted using ultra-low-carbon Al-killed steel with different Mg and Ca contents to verify the effects of Ca and Mg contents on the modification mechanism of Al_2O_3-based inclusions during secondary refining. The results showed that Al_2O_3-based inclusions can be modified into liquid calcium aluminate or a multi-component inclusion with the addition of a suitable amount of Ca. In addition, [Mg] in liquid steel can further reduce CaO in liquid calcium aluminate to drive its evolution into CaO–MgO–Al_2O_3 multi-component inclusions. Thermodynamic analysis confirmed that the reaction between [Mg] and CaO in liquid calcium aluminate occurs when the MgO content of liquid calcium aluminate is less than 3 wt% and the temperature is higher than 1843 K.

Profile improvement during CO_2 flooding in ultra-low permeability reservoirs

Gas flooding such as CO2 flooding may be effectively applied to ultra-low permeability reservoirs, but gas channeling is inevitable due to low viscosity and high mobility of gas and formation heterogeneity. In order to mitigate or prevent gas channeling, ethylenediamine is chosen for permeability profile control. The reaction mechanism of ethylenediamine with CO2, injection performance, swept volume, and enhanced oil recovery were systematically evaluated. The reaction product of ethylenediamine and CO2 was a white solid or a light yellow viscous liquid, which would mitigate or prevent gas channeling. Also, ethylenediamine could be easily injected into ultra-low permeability cores at high temperature with protective ethanol slugs. The core was swept by injection of 0.3 PV ethylenediamine. Oil displacement tests performed on heterogeneous models with closed fractures, oil recovery was significantly enhanced with injection of ethylenediamine. Experimental results showed that using ethylenediamine to plug high permeability layers would provide a new research idea for the gas injection in fractured, heterogeneous and ultra-low permeability reservoirs. This technology has the potential to be widely applied in oilfields.

The tectonic fracture modeling of an ultra-low permeability sandstone reservoir based on an outcrop analogy: A case study in the Wangyao Oilfield of Ordos Basin, China

Due to inherent limits of data acquisition and geophysical data resolution, there are large uncertainties in the characterization of subsurface fractures. However, outcrop analogies can provide qualitative and quantitative information on a large number of fractures, based on which the accuracy of subsurface fracture characterization can be improved. Here we take the tectonic fracture modeling of an ultra-low permeability sandstone reservoir based on an outcrop analogy, a case study of the Chang6t~ Formation of the Upper Triassic Yanchang Group of the Wangyao Oilfield in the Ordos Basin of China. An outcrop at the edge of the basin is a suitable analog for the reservoir, but the prerequisite is that they must have equivalent previous stress fields, similar final structural characteristics, relative timing and an identical depositional environment and diagenesis. The relationship among fracture density, rock type and bed thickness based on the outcrop is one of the most important fracture distribution models, and can be used to interpret fracture density in individual wells quantitatively. Fracture orientation, dip, geometry and scale, also should be described and measured in the outcrop, and can be used together with structure restoration and single well fracture density interpretation to guide fracture intensity prediction on bed surfaces and to constrain the construction of the 3D fracture geometry model of the subsurface reservoir. The application of the above principles shows the outcrop-based tectonic fracture models of the target ultra-low permeability sandstone reservoir are consistent with fractures inferred from microseismic interpretation and tracer tests. This illustrated that the fracture modeling based on the outcrop analogy is reliable and can reduce the uncertainty in stochastic fracture modeling.

An Ultra-Low Quiescent Current CMOS Low-Dropout Regulator with Small Output Voltage Variations

An ultra-low quiescent current low-dropout regulator with small output voltage variations and improved load regulation is presented in this paper. It makes use of dynamically-biased shunt feedback as the buffer stage and the LDO regulator can be stable for all load conditions. The proposed structure also employs a momentarily current-boosting circuit to reduce the output voltage to the normal value when output is switched from full load to no load. The whole circuit is designed in a 0.18 μm CMOS technology with a quiescent current of 550 nA. The maximum output voltage variation is less than 20 mV when used with 1 μF external capacitor.

Chemical composition,energy and amino acid digestibility in double-low rapeseed meal fed to growing pigs

Background： The nutritional value of rapeseed meal may be variable due to the variation of its chemical composition. And a precise understandin9 of the nutritional value of an ingredient is beneficial for the accurate diet formulation and reduction of feed costs. This study was conducted to determine the chemical composition, dicjestible energy （DE） and metabolizable enercjy （ME） content, and apparent ileal digestibility （AID） and standardized ileal dicjestibility （SID） of amino acids （AA） for growincj pigs. Thirteen solvent-extracted double-low rapeseed meal （DLIRSM） samples were obtained from the main double-low rapeseed producing areas in China. Methods： The DE and ME contents of the 13 DLRSM samples were measured in cjrowin9 pigs （six pigs per DLRSM sample, average initial body weicjht （BW） =48.3 kg）. The AID and SID of AA of 10 DLRSM samples were determined in 12 crossbred barrows （average initial BW = 35.3 kcj） by using two 6 x 6 Latin square designs. Each Latin square comprised one N-flee diet and 5 DLRSM test diets. Results： The chemical composition of DLRSM varied among samples, and the coefficient of variation was greater than ]0 % for ether extract （EE）, neutral detergent fiber （NDF）, acid detergent fiber （ADF）, calcium （Ca）, and total 91ucosinolates. The AA content of DLRSM varied among samples especially for lysine （Lys） and methionine （Met）. On a dry matter （DM） basis, the apparent total tract digestibility （ATFD） of gross energy （GE）, the DE and ME and the ME：DE ratio of DLRSM averaged 62.39 %, 2862 kcal/k9 and 2723 kcal/kcj, and 94.95 %, respectively. The mean value of S1D of Lys was 70.52 % which varied from 66.54-76.54 %. The SID of crude protein （CP）, Met, and threonine （Thr） averaged 72.81%, 82.41%, and 69.76 %, respectively. Conclusions： There was great variability in chemical composition especially in the concentration of EE, NDF and ADF, but no significant differences in energy content of the DLIRSM samples were observed. In addition, the AID and SID of all AA were relatively similar amoncj DLRSM samples except for that of Lys.

INVESTIGATION OF FRACTURE DESIGN FOR MEDIUM CARBON STEEL UNDER EXTRA-LOW CYCLIC FATIGUE IN AXIAL LOADING

The extra-low cyclic fracture problem of medium carbon steel under axial fatigue loading was investigated. Several problems, such as the relations of the cycle times to the depth and tip radius of the notch, loading frequency, loading range and the parameters of fracture design for medium carbon steel on condition of extra-low axial fatigue loading were discussed based on the experiments. Experimental results indicated that the tension-pressure fatigue loading mode was suitable for extra-low cyclic fatigue fracture design of medium carbon steel and it resulted in low energy consumption, fracture surface with high quality, low cycle times, and high efficiency. The appropriate parameters were as follows： loading frequency 3-5 Hz, notch tip radius r = （0.2-0.3） mm, opening angle α = 60°, and notch depth t = （0.14-0.17）D.

Physical simulation of fluid flow and production performance in extra-low permeability porous media

For extra-low permeability reservoirs, with a permeability of about 0.3×10?3 μm2, fluid flow and production performance in cores were studied. A long core holder with a multi-location piezometric measurement was specially designed. An artificial long core, about 700 mm long and with a cross section of 45mm×45mm, was used. In the experiment, pressure distribution along the core can be measured in real time. Single phase flow in the core was investigated. Different modes of production in long cores were also simulated including natural depletion, water flooding, and advanced water flooding. Through physical simulation, flow parameters were collected and production characteristics in extra-low permeability cores were studied. From experimental results, it can be seen that fluid flow in extra-low permeability cores is different from that in high permeability cores. Transmission of pressure in extra-low permeability cores is very slow, and it needs a long time for the pressure to become stable. The distribution curve of pressure along the core is nonlinear and the production rate in extra-low permeability reservoirs decreases sharply. The development effects of different production modes in extra-low permeability cores were compared with one another. Among the production modes, advanced water flooding has much potential for effective development of extra-low permeability reservoirs. Natural depletion and conventional water flooding can also be used in early production periods. In addition, the countermeasures and some ideas especially for the potential development of extra-low permeability reservoirs are suggested.

Pore structure differences of the extra-low permeability sandstone reservoirs and the causes of low resistivity oil layers: A case study of Block Yanwumao in the middle of Ordos Basin, NW China

The influence of pore structure difference on rock electrical characteristics of reservoir and oil reservoir was analyzed taking Triassic Chang 6 reservoir in Block Yanwumao in the middle of Ordos Basin as an example. The relationship between the pore structure difference and the low resistivity oil layer was revealed and demonstrated through core observation, lab experiments, geological research, well log interpretation and trial production etc. The results show that there were two kinds of oil layers in Chang 6 oil layer set, normal oil layer and low resistivity oil layer in the region, corresponding to two types of pore structures, pore type mono-medium and micro-fracture-pore type double-medium; the development of micro-fracture changed greatly the micro-pore structure of the reservoir, and the pore structure difference had an important influence on the rock electrical characteristics of the extra-low permeability sandstone reservoir and oil reservoir; the normal oil layers had obvious characteristics of pore-type mono-medium, and were concentrated in Chang 61, Chang 6232 and Chang 62; the low resistivity oil layers had obvious characteristics of micro-fracture-pore type double-medium, which were mainly distributed in Chang 612 and Chang 63. The mud filtrate penetrated deep into the oil layers along the micro-cracks, leading to sharp reduction of resistivity, and thus low resistivity of the oil layer; the low resistivity oil layers had better storage capacity and higher productivity than the normal oil layers.

Structure Character of M-A Constituent in CGHAZ of New Ultra-Low Carbon Bainitic Steel under Laser Welding Conditions

800 MPa grade new ultra-low carbon bainitic （NULCB） steel is the recently developed new generation steel. The microstructure in the coarse-grained heat affected zone （CGHAZ） of NULCB steel under laser welding conditions was investigated by thermal simulation. The influence of the cooling time from 800℃ to 500℃.t8/5 （0.3-30 s）, on the microstructure of the CGHAZ was discussed. The experimental results indicate that the microstructnre of the CGHAZ is only the granular bainite which consists of bainitic ferrite （BF） lath and M-A constituent while t8/5 is 0.3-30 s. The M-A constituent consists of twinned martensite and residual austenite, and the change of the volume fraction of the residual austenite in the M-A constituent is very small when t8/5 is between 0.3 and 30 s. The morphology of the M-A constituent obviously changes with the variation of t8/5.As t8/5 increases, tile average width, gross and shape parameter of the M-A constituent increase, while the line density of the M-A constituent decreases.

Demonstration on the indexes design of gravity satellite orbit parameters in the low-low satellite-to-satellite tracking mode

Combining with the exigent demand of the development of satellite gravimetry system in China, aiming at the determination of technical indexes of gravity satellite orbit parameters, on the basis of the numerical experiments and results analysis, the design indexes of gravity satellite orbit height, inter-satellite range and the orbit inclination are analyzed and calculated, and the issues towards twin gravity satellites such as coherence requirement of the orbit semi-major axes, control requirement of the pitch angle and time interval requirement to keep twin satellites formation in mobility are diseussed. Results show that the satellite orbit height is 400 km to 500 km, the inter-satellite range is about 220 km, the satellite orbit inclination is between polar orbit and sun-synchronous orbit, the semi-major axes difference of twin satellites orbit is within ± 70. 146 m, the pitch angle of twin satellites is about 0.9 degree, and the time interval to keep twin satellites formation in mobility is 7 days to 15 days.

Formation mechanism of spheroidal carbide in ultra-low carbon ductile cast iron

The formation mechanism of the spheroidal carbide in the ultra-low carbon ductile cast iron fabricated by the metal mold casting technique was systematically investigated. The results demonstrated that the spheroidal carbide belonged to eutectic carbide and crystallized in the isolated eutectic liquid phase area. The formation process of the spheroidal carbide was related to the contact and the intersection between the primary dendrite and the secondary dendrite of austenite. The oxides of magnesium, rare earths and other elements can act as heterogeneous nucleation sites for the spheroidal carbide. It was also found that the amount of the spheroidal carbide would increase with an increase in carbon content. The cooling rate has an important influence on the spheroidal carbide under the same chemical composition condition.

偶变元严格几乎最优弹性布尔函数的High-Meets-Low构造

在用于流密码中的布尔函数设计中,需要考虑两种重要的设计准则:弹性和非线性度,以抵抗相关攻击和最佳仿射逼近攻击.弹性和非线性度之间存在着制约关系,弹性布尔函数的非线性度的紧上界是尚未解决的公开难题.本文利用High-Meets-Low密码函数构造技术,构造出具有偶数个变元的非线性度严格几乎最优的弹性布尔函数.基于已知的具有高非线性度的m元1阶弹性布尔函数,得到非线性度为2^(n−1)−2^(n/2−1)−2^(n/2−m/4)或2^(n−1)−2^(n/2−1)−2^(n/2−(m/2−1)/2)的n元高阶弹性布尔函数.采用所提方法,可以得到一些具有目前已知最高非线性度的高阶弹性布尔函数,这可由两个参数分别为(22,4,2^(21)−2^(10)−29)和(30,4,2^(29)−2^(14)−2^(12))的弹性布尔函数例子得到证实.

The control effect of low-amplitude structure on oil-gaswater enrichment and development performance of ultra-low permeability reservoirs

Based on drilling, logging, test production and dynamic monitoring data, the control effects of low-amplitude structure on hydrocarbon accumulation and development performance of ultra-low permeability reservoirs were discussed by using the methods of dense well pattern, multi-factor geological modeling, macro and micro analysis and static and dynamic analysis. The results show that the low-amplitude structure always had a significant control and influence on the distribution and accumulation of original hydrocarbon and water and the evolution trend of water flooding performance in ultra-low permeability reservoirs, and it was not only the direction of oil and gas migration, but also a favorable place for relative accumulation of oil and gas. The controlling effect of low-amplitude structure on ultra-low permeability reservoir mainly depended on its tectonic amplitude and scale;the larger the tectonic amplitude and scale, and the higher the tectonic position of the low amplitude structure, the better the reservoir characteristic parameters, oil and gas enrichment degree and development effect, and the larger the spatial scope it controlled and influenced;water cut and oil well output always fluctuated orderly with the height of the low-amplitude structure;the dynamic response of waterflooding was closely related to the relative structural position of the injection and production wells;the injected water always advanced to the low-lying area of the structure first and then moved up to the high-lying area of the structure gradually;with the continuous expansion of the flooded area, part of the oil and gas in the low-lying part of the structure was forced to be distributed to the high part of the structure, resulting in a new oil and gas enrichment, so that the dynamic reserves of oil wells in the high part increased, and the production capacity remained stable.

SWOT Analysis of Industrial Development of Double-low Rapeseed in Hubei Province

Based on SWOT analysis method,this paper conducts analysis on the industrial development environment of double-low rapeseed in Hubei Province from the following four aspects,in order to crystallize its resources advantage and disadvantage and make it know the opportunities and challenges that it is faced by.First,advantage analysis:excellent geographic conditions,vigorous government support,powerful scientific research force,sound industrial system support;second,disadvantage analysis:poor quality,low-level fine and deep processing,scant publicity and promotion,lagged infrastructure conditions,shortage of effective market access mechanism and sound industry regulation,no brand effect;opportunity analysis:the opportunities brought by low-carbon economy,the opportunities brought by consumers' preference,the opportunities brought by policy environment,the opportunities brought by establishment of strategic union;threat analysis:fierce external competition,continuous decline of comparative benefit.The results of research show that in order to promote industrial development of double-low rapeseed in Hubei Province,we should implement brand effect strategy,quality management strategy and strategy of deepening industrial system,give full play to existing geographic advantage and other advantages,grasp scarce opportunities and actively confront challenges.

High microwave absorption performances for single-walled carbon nanotube–epoxy composites with ultra-low loadings

Microwave-absorbing polymeric composites based on single-walled carbon nanotubes （SWNTs） are fabricated via a simple yet versatile method, and these SWNT-epoxy composites exhibit very impressive microwave absorption perfor- mances in a range of 2 GHz-18 GHz. For instance, a maximum absorbing value as high as 28 dB can be achieved for each of these SWNT-epoxy composites （1.3-mm thickness） with only 1 wt% loading of SWNTs, and about 4.8 GHz bandwidth, corresponding to a microwave absorption performance higher than 10 dB, is obtained. Furthermore, such low and appro- priate loadings of SWNTs also enhance the mechanical strength of the composite. It is suggested that these remarkable results are mainly attributable to the excellent intrinsic properties of SWNTs and their homogeneous dispersion state in the polymer matrix.