Box-Behnken响应面法优化葛根异黄酮提取纯化工艺及损伤心肌细胞治疗作用研究

目的:采用Box-Behnken响应面优化葛根异黄酮最佳提取工艺,并研究葛根异黄酮对损伤心肌细胞的治疗作用。方法:在单因素实验的基础上,以料液比、提取时间、溶剂浓度为考察因素,以3'-羟基葛根素、葛根素、3'-甲氧基葛根素、大豆苷的含量为评价指标,采用Box-Behnken响应面法设计实验,以葛根异黄酮总提取率为考察指标,通过分析回归方程模型,优选最佳提取工艺并验证工艺;采用MTT法检测葛根异黄酮对损伤心肌细胞的治疗作用。结果:Box-Behnken响应面法优化得到葛根异黄酮最佳提取工艺为:料液比为30 mg·mL^(-1),提取时间为100 min,乙醇体积分数为73%,葛根异黄酮的总提取率平均值为41.6 mg·g^(-1),与预测值42.08 mg·g^(-1),相对误差0.81%;葛根异黄酮对H 2O_(2)损伤的缺氧复氧模型和Na 2S_(2)O 4损伤的缺血再灌注模型OD值分别为0.7436±0.0292和0.7457±0.0094,细胞存活率分别为81.32%和73.41%。结论:优选葛根抗氧化活性异黄酮最佳工艺稳定,预测模型效果良好,且葛根异黄酮对心肌缺血有良好的治疗作用。

一类单调递减正项数列的BOX维数估计

当使用比较原则、 柯西判别法在讨论正项级数敛散性时,会遇到比值极限为1从而无法使用的情况,典型的例子为数组{1/n}和{1/n2}的正项级数具有不同的敛散性。 本文讨论了形如1/na(α > 0) 正项级数的敛散性与对应点集的BOX维数存在一定关联,当点集的BOX维数大于等于1/2时,正项级数发散;小于1/2时,正项级数收敛,同时提出了利用1/n为参照对象判断数列正项级数敛散性的一种新方法。

Box-Behnken响应面法优选紫斑牡丹中丹皮酚和芍药苷提取工艺

目的优选紫斑牡丹中丹皮酚和芍药苷的提取工艺。方法在单因素试验基础上,以液料比、提取时间和乙醇体积分数为影响因素,以丹皮酚和芍药苷提取率的总权重综合评分为评价指标,采用Box-Behnken响应面法优选最佳提取工艺,并进行验证试验。结果最佳提取工艺为液料比28倍,提取时间150 min,乙醇体积分数52%。此工艺条件下,丹皮酚提取率为0.49%(RSD=1.33%,n=3),芍药苷提取率为5.38%(RSD=1.07%,n=3)。结论该提取工艺稳定、可行,可用于紫斑牡丹中丹皮酚和芍药苷的提取。

蓝莓B-box型锌指蛋白基因家族的鉴定及其在果实发育期的表达模式

B-box(BBX)基因家族成员在植物生长发育中起重要作用.为探究BBX在蓝莓果实成熟发育过程中的作用,通过生物信息学的方法鉴定BBX基因家族成员,并对其进行染色体定位、系统进化关系、基因结构、启动子顺式作用元件及表达模式分析.结果表明:在蓝莓基因组中鉴定出38个BBX基因成员,基因结构保守,外显子平均个数为3.13,这些基因可分成Ⅰ~Ⅲ3个亚族,不均匀分布于23条染色体;BBX基因的启动子序列中存在光响应、植物激素响应、胁迫响应和植物生长发育等4类顺式作用元件;VcBBX基因成员在‘Star’和‘O’Neal’蓝莓果实发育过程中存在显著性差异表达,VcBBX9,VcBBX16,VcBBX25和VcBBX20在S8表达量最高,VcBBX26在S6表达量最高,VcBBX30在S3表达量最高.研究结果将为进一步探究BBX型锌指蛋白在蓝莓果实发育过程中的功能奠定基础.

Analytical computation of magnetic field in coil-dominated superconducting quadrupole magnets based on racetrack coils

Currently,three types of superconducting quadrupole magnets are used in particle accelerators:cos 2θ,CCT,and serpentine.However,all three coil configurations have complex spatial geometries,which make magnet manufacturing and strain-sensitive superconductor applications difficult.Compared with the three existing quadrupole coils,the racetrack quadrupole coil has a simple shape and manufacturing process,but there have been few theoretical studies.In this paper,the two-dimensional and three-dimensional analytical expressions for the magnetic field in coil-dominated racetrack superconducting quadrupole magnets are presented.The analytical expressions of the field harmonics and gradient are fully resolved and depend only on the geometric parameters of the coil and current density.Then,a genetic algorithm is applied to obtain a solution for the coil geometry parameters with field harmonics on the order of 10^(-4).Finally,considering the practical engineering needs of the accelerator interaction region,electromagnetic design examples of racetrack quadrupole magnets with high gradients,large apertures,and small apertures are described,and the application prospects of racetrack quadrupole coils are analyzed.

Gradient coil design with enhanced shielding constraint for a cryogen-free superconducting MRI system

The relatively fragile low-temperature stability of cryogen-free superconducting magnetic resonance imaging(MRI)magnets requires the careful management of exogenous heat sources.A strongly shielded gradient magnetic field is important for the optimal operation of cryogen-free MRI systems.In this study,we present an enhanced shielding method incorporating a regionalized stray field constraining strategy.By optimizing the constraint parameters,we could develop engineering-feasible gradient coil schemes without increasing system complexity but with the stray field intensity reduced by half.In real measurement in an integrated MRI system,the developed gradient assembly demonstrated good performance and supported to output images of excellent quality.Our findings suggested that the proposed method could potentially form a useful design paradigm for cryogen-free MRI magnets.

基于Box-Behnken响应面法优化鹿角蛋白的提取工艺

目的 通过Box-Behnken响应面法优化鹿角蛋白的提取工艺。方法 在单因素考察基础上进行响应面法设计,寻找最佳提取条件。以鹿角中蛋白含量为考察指标,使用考马斯亮蓝染色法测量样品溶液吸光度,再通过回归方程计算出样品溶液的鹿角蛋白含量。结果 最优提取工艺条件为NaOH浓度0.35 mol·L^(-1),液料比6:1,提取时间114 min。结论 经验证通过Box-Behnken响应面法所得到的预测值与测定的实际值偏差均在±1%以内,可以为膝痛康中鹿角蛋白的提取工艺提供参考。

RNA解旋酶DEAD-box蛋白家族与肿瘤的相关性研究

RNA解旋酶DEAD-box蛋白家族是RNA解旋酶中最大的家族,是基因表达的重要调控因子,在RNA代谢的多个方面发挥作用。RNA解旋酶DEAD-box蛋白家族既在RNA代谢中具有重要作用,又与人类细胞中基因组的不稳定性直接相关。而基因组的不稳定性是癌症克隆进化的驱动因素,能够促进癌症的发生发展。该文对RNA解旋酶DEAD-box蛋白家族与肿瘤发生发展的相关性做一综述。

Effect of coil and chamber structure on plasma radial uniformity in radio frequency inductively coupled plasma

Enhancing plasma uniformity can be achieved by modifying coil and chamber structures in radio frequency inductively coupled plasma(ICP)to meet the demand for large-area and uniformly distributed plasma in industrial manufacturing.This study utilized a two-dimensional self-consistent fluid model to investigate how different coil configurations and chamber aspect ratios affect the radial uniformity of plasma in radio frequency ICP.The findings indicate that optimizing the radial spacing of the coil enhances plasma uniformity but with a reduction in electron density.Furthermore,optimizing the coil within the ICP reactor,using the interior point method in the Interior Point Optimizer significantly enhances plasma uniformity,elevating it from 56%to 96%within the range of the model sizes.Additionally,when the chamber aspect ratio k changes from 2.8 to 4.7,the plasma distribution changes from a center-high to a saddleshaped distribution.Moreover,the plasma uniformity becomes worse.Finally,adjusting process parameters,such as increasing source power and gas pressure,can enhance plasma uniformity.These findings contribute to optimizing the etching process by improving plasma radial uniformity.

柳属植物花发育相关的MADS-box基因家族成员鉴定与表达分析

【目的】利用基因组和转录组数据鉴定分析花发育相关的MADS-box基因家族成员的结构特征及表达模式,为柳属花被缺失的分子机制研究提供理论依据。【方法】通过生物信息学方法鉴定柳属的长梗柳(Salix dunnii)、欧蒿柳(S.viminalis)、红皮柳(S.purpurea)的MADS-box基因家族成员,并对3种柳树花发育相关的MADS-box基因系统发育关系、基因复制和丢失、基因结构和理化性质进行分析。根据雌雄花芽的转录组数据分析长梗柳花发育相关基因在花芽不同发育阶段的表达模式。【结果】在长梗柳、欧蒿柳和红皮柳中分别鉴定出82、82和98个MADS-box家族基因。3种柳树的花发育相关基因经历了基因复制和丢失,相同亚类基因结构和保守结构域相似,但部分A、B、C和E亚类基因的K-box结构域缺失。长梗柳花发育相关基因的表达结果显示,在雌花和雄花中具有不同的表达模式。其中,B亚类SdMADS26和SdMADS4基因表达量均偏低。【结论】柳属植物花发育相关基因中部分成员的基因结构和表达模式发生了变化,推测这些变化可能与柳属花被缺失相关。

大豆MADS-box基因功能研究进展

MADS-box是植物体内一种重要的转录因子,其家族成员具有典型的MIKC结构、高度保守的N端MADS以及保守性较低的I域和C端。MADS-box基因广泛表达于植物的根、茎、叶、花、芽等组织部位,并参与调控花期、花器官发育、种子发育及非生物胁迫响应等过程。近年来的研究报道显示,不同MADS-box基因的表达模式不尽相同,其功能也存在较大差异。本文概述了大豆MADS-box基因家族的结构及分类,总结了大豆MADS-box基因家族花发育ABCDE模型中相关成员及SVP、SOC1、FLC等基因的研究进展。最后对大豆MADS-box的研究提出了展望,为今后进一步挖掘和利用该类转录因子基因进行大豆遗传改良和种质创新提供参考依据。

基于Box-Behnken响应面法优化膝痛康β-蜕皮甾酮的提取工艺

目的优化膝痛康方剂中β-蜕皮甾酮的提取工艺。方法采用Box-Behnken响应面法和单因素试验,对提取过程中的浸泡时间、提取次数、提取时间和甲醇倍量等进行优化,通过响应面模型分析与预测,得到最佳的提取工艺条件,并对最优条件进行验证。结果饮片浸泡96 min,提取100 min,反复2次,甲醇倍数为16倍,此时牛膝的提取工艺达到最佳,在此提取工艺下β-蜕皮甾酮的提取量达到最大。结论该提取方法具有设备简单、成本低、提取工艺稳定等特点,此外,该提取工艺具有较好的应用价值,以其为膝痛康的应用提供实验依据。

Fuzzy Proportional Integral Derivative control of a voice coil actuator system for adaptive deformable mirrors

Research on adaptive deformable mirror technology for voice coil actuators(VCAs)is an important trend in the development of large ground-based telescopes.A voice coil adaptive deformable mirror contains a large number of actuators,and there are problems with structural coupling and large temperature increases in their internal coils.Additionally,parameters of the traditional proportional integral derivative(PID)control cannot be adjusted in real-time to adapt to system changes.These problems can be addressed by introducing fuzzy control methods.A table lookup method is adopted to replace real-time calculations of the regular fuzzy controller during the control process,and a prototype platform has been established to verify the effectiveness and robustness of this process.Experimental tests compare the control performance of traditional and fuzzy proportional integral derivative(Fuzzy-PID)controllers,showing that,in system step response tests,the fuzzy control system reduces rise time by 20.25%,decreases overshoot by 78.24%,and shortens settling time by 67.59%.In disturbance rejection experiments,fuzzy control achieves a 46.09%reduction in the maximum deviation,indicating stronger robustness.The Fuzzy-PID controller,based on table lookup,outperforms the standard controller significantly,showing excellent potential for enhancing the dynamic performance and disturbance rejection capability of the voice coil motor actuator system.

Explosion resistance performance of reinforced concrete box girder coated with polyurea:Model test and numerical simulation

To study the anti-explosion protection effect of polyurea coating on reinforced concrete box girder,two segmental girder specimens were made at a scale of 1:3,numbered as G(without polyurea coating)and PCG(with polyurea coating).The failure characteristics and dynamic responses of the specimens were compared through conducting explosion tests.The reliability of the numerical simulation using LS-DYNA software was verified by the test results.The effects of different scaled distances,reinforcement ratios,concrete strengths,coating thicknesses and ranges of polyurea were studied.The results show that the polyurea coating can effectively enhance the anti-explosion performance of the girder.The top plate of middle chamber in specimen G forms an elliptical penetrating hole,while that in specimen PCG only shows a very slight local dent.The peak vertical displacement and residual displacement of PCG decrease by 74.8% and 73.7%,respectively,compared with those of specimen G.For the TNT explosion with small equivalent,the polyurea coating has a more significant protective effect on reducing the size of fracture.With the increase of TNT equivalent,the protective effect of polyurea on reducing girder displacement becomes more significant.The optimal reinforcement ratio,concrete strength,thickness and range of polyurea coating were also drawn.

Mathematical Modelling and Design of Helical Coil Heat Exchanger for Production of Hot Air for Fluidized Bed Dryer

In global industrialization, efforts have been made to increase the rate of heat transfer in heat exchanger, minimizing the size of heat exchanger to reduce cost as well as increasing the effectiveness. Helical coil heat exchanger (HCHE) has been proven to be effective in improving heat transfer due to its large surface area. In this study, HCHE was designed to provide hot air needed for fluidized bed drying processes. The HCHE design model was fabricated and evaluated to study the efficiency of the hot air output for a laboratory fluidized bed dryer. The mathematical model for estimation of the final (output) temperature of air, Taf, passing through the HCHE was developed and validated experimentally. The drying of bitter kola particulates was carried out with a drying temperature of 50C 3C and a bed height-to-bed diameter ratio (H/D) of 1.5. The time taken to dry bitter kola particulates to 0.4% moisture content was 1 hour 45 minutes. Hence, HCHE is recommended for use in the production of hot for laboratory-scale fluidized bed dryers.

Fatigue Crack Propagation Law of Corroded Steel Box Girders in Long Span Bridges

In order to investigate the fatigue performance of orthotropic anisotropic steel bridge decks,this study realizes the simulation of the welding process through elastic-plastic finite element theory,thermal-structural sequential coupling,and the birth-death element method.The simulated welding residual stresses are introduced into the multiscale finite element model of the bridge as the initial stress.Furthermore,the study explores the impact of residual stress on crack propagation in the fatigue-vulnerable components of the corroded steel box girder.The results indicate that fatigue cracks at the weld toe of the top deck,the weld root of the top deck,and the opening of the transverse diaphragm will not propagate under the action of a standard vehicle load.However,the inclusion of residual stress leads to the propagation of these cracks.When considering residual stress,the fatigue crack propagation paths at the weld toe of the transverse diaphragm and the U-rib weld toe align with those observed in actual bridges.In the absence of residual stress,the cracks at the toe of the transverse diaphragm with a 15%mass loss rate are categorized as type I cracks.Conversely,when residual stress is considered,these cracks become I-II composite cracks.Residual stress significantly alters the cumulative energy release rate of the three fracturemodes.Therefore,incorporating the influence of residual stress is essential when assessing the fatigue performance of corroded steel box girders in long-span bridges.

Box-Behnken响应面法优选改良型正骨灵活血止痛膏成型工艺

目的:优选改良型正骨灵活血止痛膏成型工艺。方法:基于Box–Behnken响应面法,以蜂蜡用量、混合温度、料液比为影响因素,以传统经验鉴别法与客观物理参数法的综合评分为评价指标,在单因素试验基础上,考察各因素对综合评分的影响,优选最佳的成型工艺条件。结果:蜂蜡用量为1.9%,混合温度为81℃,料液比为2.5∶1 g/mL。验证试验结果综合评分RSD为0.86%。结论:优选得到的改良型正骨灵活血止痛膏成型工艺稳定可行。

Box-Behnken响应面法优化羟基红花黄色素A纳米粒处方工艺及体外释放评价

目的优化羟基红花黄色素A(hydroxysafflor yellow A,HSYA)纳米粒制备工艺,并对其进行体外释放评价。方法以乳酸-羟基乙酸共聚物[poly(lactic-co-glycolicacid),PLGA]为载体,利用改良的复乳法制备HSYA纳米粒,通过Plackett-Burman设计实验联用Box-Behnken响应面法优选最佳制备工艺;利用粒径测定仪、TEM扫描电镜仪、傅里叶红外光谱(FT-IR)仪、X-射线粉末衍射(XRD)仪对纳米粒进行表征;并对其进行4℃储藏稳定性、生理介质中稳定性、冻干保护剂及体外释放率考察。结果优选出纳米粒最佳工艺处方为:pH为6.95,投药量为2.8 mg,载体用量为18.2 mg;在此条件下制备出的纳米粒粒径为(176.4±1.29)nm,多分散系数(Polydiseperse Index,PDI)为(0.152±0.014),Zeta电位为(-17.6±0.46)mV,包封率为(78.5±0.49)%,载药量为(7.3±0.07)%,纳米粒形态圆整,分散性好;在4℃储存环境下、不同生理介质中稳定性良好,最佳冻干保护剂为1%葡萄糖;纳米粒48 h体外释放率为85%。结论该优化方法合理可靠,所得纳米粒稳定性良好,具有一定的缓释作用,体外释放符合一级动力学模型。

灰毡毛忍冬MADS-box基因家族鉴定与CMB1基因克隆

目的鉴定灰毡毛忍冬Lonicera macranthoides MADS-box家族基因并进行生物信息学分析与表达模式验证,克隆湘蕾型和野生型灰毡毛忍冬MADS-box家族成员CMB1全长。方法基于转录组数据,利用在线工具对灰毡毛忍冬MADS-box进行生物信息学分析,并利用qRT-PCR验证MADS-box基因在不同品种中的表达模式,通过RT-PCR、RACE技术克隆湘蕾型和野生型灰毡毛忍冬CMB1基因全长。结果28个灰毡毛忍冬MADS-box蛋白长度为89~359 aa,碱性蛋白占比85.7%,不稳定蛋白占比96.4%,亲水性蛋白占比96.4%,均定位于细胞核,均为无跨膜结构的非分泌蛋白。转录组显示,与野生型比较,湘蕾型中28个MADS-box基因有17.86%表达下调,MIKCC型基因中有18.75%表达下调。克隆得到在两个品种的灰毡毛忍冬花中高度特异性表达的CMB1基因全长,均包含一个738 bp的ORF,编码245个氨基酸。CMB1基因在两个品种的花中表达量存在显著差异(P<0.01),且与茎、叶相比,在花中高度特异性表达(P<0.01)。结论基于灰毡毛忍冬转录组数据,鉴定了28个MADS-box家族基因,克隆得到湘蕾型与野生型灰毡毛忍冬CMB1基因全长,为进一步研究灰毡毛忍冬花发育、优良表型形成的分子机制提供研究基础与理论依据。

Boom Box 3爆炸机独立激发新模式应用开发与测试

随着国内外节点仪的应用,采用全节点仪采集的项目越来越多,有线地震仪的井炮激发方式已经不能完全适用于全节点采集系统,因此,针对全节点采集项目,以“去有线采集系统和无线电台通讯网络”为核心思路,开发出基于Boom Box 3爆炸机的独立激发新模式。本文通过对独立激发新模式的研发思路、放炮操作流程、炮后信息下载以及测试等各方面进行了详细介绍,最后,对基于Boom Box 3爆炸机独立激发新模式的优点进行了分析。