During a hypothetical severe accident of light water reactors,the reactor pressure vessel(RPV) could fail due to its creep under the influence of high-temperature corium.Hence,modelling of creep behavior of the RPV is...During a hypothetical severe accident of light water reactors,the reactor pressure vessel(RPV) could fail due to its creep under the influence of high-temperature corium.Hence,modelling of creep behavior of the RPV is paramount to reactor safety analysis since it predicts the transition point of accident progression from in-vessel to ex-vessel phase.In the present study we proposed a new creep model for the classical French RPV steel 16 MND5,which is adapted from the "theta-projection model" and contains all three stages of a creep process.Creep curves are expressed as a function of time with five model parameters θ_i(i=1-4 and m).A model parameter dataset was constructed by fitting experimental creep curves into this function.To correlate the creep curves for different temperatures and stress loads,we directly interpolate the model’s parameters θ_i(i=1-4 and m) from this dataset,in contrast to the conventional "theta-projection model" which employs an extra single correlation for each θ_i(i=1-4 andm),to better accommodate all experimental curves over the wide ranges of temperature and stress loads.We also put a constraint on the trend of the creep strain that it would monotonically increase with temperature and stress load.A good agreement was achieved between each experimental creep curve and corresponding model’s prediction.The widely used time-hardening and strain-hardening models were performing reasonably well in the new method.展开更多
Electrical additive manufacturing can improve manufacturing efficiency and reduce the cost of 16MND5 reactor pres-sure vessel steel. Impact tests were conducted to compare the impact toughness of 16MND5 steels manufac...Electrical additive manufacturing can improve manufacturing efficiency and reduce the cost of 16MND5 reactor pres-sure vessel steel. Impact tests were conducted to compare the impact toughness of 16MND5 steels manufactured by the electrical additive manufacturing and conventional forging, respectively. It is found that the impact toughness of electrical additive manufacturing specimen was slightly higher than that of conventional forging specimen. The characterizations of microstructure show that there were large ferrites and carbides in electrical additive manufacturing specimen. The fracture mechanisms of electrical additive manufacturing specimen were that microvoids or microcracks were prone to nucleate at the large ferrite/bainite interface and large carbide/bainitic ferrite interface, where the stress concentration was high. In addi-tion, the block size and high-angle grain boundaries played a vital role in hindering crack propagation of electrical additive manufacturing specimen, helping to improve the impact energy and leading to a low ductile–brittle transition temperature. The results suggest that the electrical additive manufacturing technology was an effective method to enhance the impact toughness of 16MND5 steel.展开更多
基金support from the research programs of APRI,ENSI and NKSsupport of the scholarship awarded by the China Scholarship Council(CSC)。
文摘During a hypothetical severe accident of light water reactors,the reactor pressure vessel(RPV) could fail due to its creep under the influence of high-temperature corium.Hence,modelling of creep behavior of the RPV is paramount to reactor safety analysis since it predicts the transition point of accident progression from in-vessel to ex-vessel phase.In the present study we proposed a new creep model for the classical French RPV steel 16 MND5,which is adapted from the "theta-projection model" and contains all three stages of a creep process.Creep curves are expressed as a function of time with five model parameters θ_i(i=1-4 and m).A model parameter dataset was constructed by fitting experimental creep curves into this function.To correlate the creep curves for different temperatures and stress loads,we directly interpolate the model’s parameters θ_i(i=1-4 and m) from this dataset,in contrast to the conventional "theta-projection model" which employs an extra single correlation for each θ_i(i=1-4 andm),to better accommodate all experimental curves over the wide ranges of temperature and stress loads.We also put a constraint on the trend of the creep strain that it would monotonically increase with temperature and stress load.A good agreement was achieved between each experimental creep curve and corresponding model’s prediction.The widely used time-hardening and strain-hardening models were performing reasonably well in the new method.
基金This work was financially supported by the Nuclear Power Technology Innovation Center(HDLCXZX-2018-HD-027-03)Science and Technology on Reactor System Design Technology Laboratory(HT-KFKT-02-2017006).
文摘Electrical additive manufacturing can improve manufacturing efficiency and reduce the cost of 16MND5 reactor pres-sure vessel steel. Impact tests were conducted to compare the impact toughness of 16MND5 steels manufactured by the electrical additive manufacturing and conventional forging, respectively. It is found that the impact toughness of electrical additive manufacturing specimen was slightly higher than that of conventional forging specimen. The characterizations of microstructure show that there were large ferrites and carbides in electrical additive manufacturing specimen. The fracture mechanisms of electrical additive manufacturing specimen were that microvoids or microcracks were prone to nucleate at the large ferrite/bainite interface and large carbide/bainitic ferrite interface, where the stress concentration was high. In addi-tion, the block size and high-angle grain boundaries played a vital role in hindering crack propagation of electrical additive manufacturing specimen, helping to improve the impact energy and leading to a low ductile–brittle transition temperature. The results suggest that the electrical additive manufacturing technology was an effective method to enhance the impact toughness of 16MND5 steel.
