Based on the statistical model for the tensile statistical strength of unidirectional composite materials and the stress analysis of 3-D braided composites, a new method is proposed to calculate the tensile statistica...Based on the statistical model for the tensile statistical strength of unidirectional composite materials and the stress analysis of 3-D braided composites, a new method is proposed to calculate the tensile statistical strength of the 3-D braided compos- ites. With this method, the strength of 3-D braided composites can be calculated with very large accuracy, and the statistical parameters of 3-D braided composites can be determined. The numerical result shows that the tensile statistical strength of 3-D braided composites can be predicted using this method.展开更多
In Ref [1] a model of 3-D composite laminate theory was described In the present paper,based on the basic equations about 3-D linear elasticity and classicalrariational principles,by the block matrix operation and the...In Ref [1] a model of 3-D composite laminate theory was described In the present paper,based on the basic equations about 3-D linear elasticity and classicalrariational principles,by the block matrix operation and the Lagrange's method of multipliers a series of basic equations and variational principles are obtained whichare more complere and more systematic than that in Ref [1]展开更多
The yarn architecture of 3-D braided composites products by the four-step 1×1 braiding technique has been studied by means of a control volume method in conjunction with experimental investigation and a numerical...The yarn architecture of 3-D braided composites products by the four-step 1×1 braiding technique has been studied by means of a control volume method in conjunction with experimental investigation and a numerical method, respectively. An ellipse assumption for the cross-section of yarn was proposed in this analysis method with considering the yarn size and yarn-packing factor. Two types of local unit cell structures were identified for 4-step braided composites by considering the nature of the braiding processes and by observing the sample cross-sections. The relationship between the braiding procedure and the properties for 3-D braided structural shapes was established. This method provides the basis for analyzing stiffness and strength of 3-D braided composites.展开更多
Generally, friction and wear occur on the surface of the materials. It is necessary to investigate the dry sliding friction and wear behavior of surface. In this paper, 3-D topographical parameters were used to invest...Generally, friction and wear occur on the surface of the materials. It is necessary to investigate the dry sliding friction and wear behavior of surface. In this paper, 3-D topographical parameters were used to investigate the topographical characteristics of dry sliding surfaces for particle-reinforced alu-minum composites on semi-metallic friction material. The experimental results indicate that the surface topography of the particle-reinforced aluminum composites can be divided into two types, the flaking-off pit type and the groove type. The composites whose surface topography is the flaking-off pit type possess superior heat conductivity and bearing area, lower wear rate, and higher friction coefficient than the groove type. Consequently, the flaking-off pit type surface topography is much better than the groove type for particle-reinforced aluminum composites on semi-metallic friction materials in dry sliding.展开更多
基金Supported by the National Natural Science Foundation of China(51075031)
文摘Based on the statistical model for the tensile statistical strength of unidirectional composite materials and the stress analysis of 3-D braided composites, a new method is proposed to calculate the tensile statistical strength of the 3-D braided compos- ites. With this method, the strength of 3-D braided composites can be calculated with very large accuracy, and the statistical parameters of 3-D braided composites can be determined. The numerical result shows that the tensile statistical strength of 3-D braided composites can be predicted using this method.
文摘In Ref [1] a model of 3-D composite laminate theory was described In the present paper,based on the basic equations about 3-D linear elasticity and classicalrariational principles,by the block matrix operation and the Lagrange's method of multipliers a series of basic equations and variational principles are obtained whichare more complere and more systematic than that in Ref [1]
基金Aeronautical Science Foundation of China ( 99B2 3 0 0 1)
文摘The yarn architecture of 3-D braided composites products by the four-step 1×1 braiding technique has been studied by means of a control volume method in conjunction with experimental investigation and a numerical method, respectively. An ellipse assumption for the cross-section of yarn was proposed in this analysis method with considering the yarn size and yarn-packing factor. Two types of local unit cell structures were identified for 4-step braided composites by considering the nature of the braiding processes and by observing the sample cross-sections. The relationship between the braiding procedure and the properties for 3-D braided structural shapes was established. This method provides the basis for analyzing stiffness and strength of 3-D braided composites.
基金Supported by the Innovation Fund for Outstanding Scholar of Henan Province (No. 0421000600)
文摘Generally, friction and wear occur on the surface of the materials. It is necessary to investigate the dry sliding friction and wear behavior of surface. In this paper, 3-D topographical parameters were used to investigate the topographical characteristics of dry sliding surfaces for particle-reinforced alu-minum composites on semi-metallic friction material. The experimental results indicate that the surface topography of the particle-reinforced aluminum composites can be divided into two types, the flaking-off pit type and the groove type. The composites whose surface topography is the flaking-off pit type possess superior heat conductivity and bearing area, lower wear rate, and higher friction coefficient than the groove type. Consequently, the flaking-off pit type surface topography is much better than the groove type for particle-reinforced aluminum composites on semi-metallic friction materials in dry sliding.
