In-situ 3D contour measurement for laser powder bed fusion based on phase guidance

In-situ layerwise imaging measurement of laser powder bed fusion(LPBF)provides a wealth of forming and defect data which enables monitoring of components quality and powder bed homogeneity.Using high-resolution camera layerwise imaging and image processing algorithms to monitor fusion area and powder bed geometric defects has been studied by many researchers,which successfully monitored the contours of components and evaluated their accuracy.However,research for the methods of in-situ 3D contour measurement or component edge warping identification is rare.In this study,a 3D contour mea-surement method combining gray intensity and phase difference is proposed,and its accuracy is verified by designed experiments.The results show that the high-precision of the 3D contours can be achieved by the constructed energy minimization function.This method can detect the deviations of common ge-ometric features as well as warpage at LPBF component edges,and provides fundamental data for in-situ quality monitoring tools.

Ca_(2)MgTeO_(6)∶Bi^(3+),Mn^(4+)材料的发光性能和温度探测

通过高温固相法成功制备了一系列Ca_(2)MgTeO_(6)∶Bi^(3+),Mn^(4+)荧光粉,对其微观结构、形貌、发光特性和温敏特性进行了表征。Ca_(2)MgTeO_(6)∶Bi^(3+),Mn^(4+)荧光粉具有不同温度敏感性的双发射中心,分别来自于Bi^(3+)离子^(3)P_(1)→^(1)S_(0)跃迁和Mn^(4+)离子的^(2)E_(g)→^(4)A_(2g)跃迁。由于Bi^(3+)、Mn^(4+)离子的发光强度随温度变化的规律不同,利用该特性进行测温研究,在200~500 K范围内,该荧光粉的最大绝对灵敏度和相对灵敏度分别达到0.027 K^(-1)和1.83%·K^(-1),并且观察到荧光粉的发光颜色由橙黄色逐渐变为紫红色。实验结果表明,Ca_(2)MgTeO_(6)∶Bi^(3+),Mn^(4+)荧光粉作为光学测温材料在温度探测方面有一定的潜力。

3D LDV MEASUREMENTS OF ROTOR BLADE TIP VORTEX IN HOVER

An investigation made on the rotor blade tip vortex through use of a Three Dimensional Laser Doppler Velocimetry(3D LDV) is described. The experiment is conducted with a 2 m in diameter model helicopter rotor. By a series of measurements near blade tip, the velocity field near blade tip is documented, and through which, the tip vortex rollup and development are presented. The radial distribution of instantaneous velocities at various levels above and under the rotor disc is also measured in this investigation. Using this distribution, the influence of the tip vortex from the preceding blade on the follow up blade is discussed.

Intrinsic background radiation of LaBr3(Ce)detector via coincidence measurements and simulations

The LaBr3(Ce)detector has attracted much attention in recent years because of its superior characteristics compared with other scintillating materials in terms of resolution and efficiency.However,it has a relatively high intrinsic background radiation because of the naturally occurring radioisotopes in lanthanum,actinium,and their daughter nuclei.This limits its applications in low-counting rate experiments.In this study,we identified the radioactive isotopes in theφ3"x 3"Saint-Gobain B380 detector by a coincidence measurement using a Clover detector in a low-background shielding system.Moreover,we carried out a Geant4 simulation of the experimental spectra to evaluate the activities of the main internal radiation components.The total activity of the background radiation of B380 is determined to be 1.523(34)Bq/cm^3.The main sources include 138La at 1.428(34)Bq/cm^3,207Tl at 0.0135(13)Bq/cm^3,211Bi at 0.0136(15)Bq/cm^3,215Po at 0.0135(3)Bq/cm^3,219Rn at 0.0125(12)Bq/cm^3,223Fr at 0.0019(11)Bq/cm^3,223Ra at 0.0127(10)Bq/cm^3,227Th at 0.0158(22)Bq/cm^3,and 227Ac at 0.0135(13)Bq/cm^3.Of these,the activities of 207Tl,211Po,215Po,223Fr,and 227Ac are deduced for the first time from the secular equilibrium established in the decay chain of 227Ac.

HL-3装置测量基准网的建立及部件定位测量

根据HL-3装置总装集成设计安装精度的要求,需要建立一个高精度的测量基准网,在总装过程中采用激光跟踪仪等先进测量设备对安装部件的空间位置进行测量。建立的基准网实现了网内基准点空间坐标最大不确定度为0.133mm。特别在对真空室、临时第一壁/限制器等部件的安装中,进行定位测量和数据反馈,然后再进行安装调整,实现了真空室∅1.84mm的同轴度精度,满足同轴度≤∅3mm的要求;标高偏差为-0.08~+0.136mm,满足标高偏差≤±1mm的要求。临时第一壁/限制器安装最大偏差值为+1.9351mm,最小偏差值为-1.8337mm,均满足各模块表面位置误差不超过±2mm的技术要求。测量基准网的建立以及安装过程中对部件高精度的定位测量,保证了HL-3装置高质量的建造。

An Improved Calibration Method of Grating Projection Measurement System

In the traditional fringe projection profilometry system,the projector and the camera light center are both spatially virtual points.The spatial position relationships specified in the model are not easy to obtain,leading to inaccurate system parameters and affectingmeasurement accuracy.This paper proposes a method for solving the system parameters of the fringe projection profilometry system,and the spatial position of the camera and projector can be adjusted in accordance with the obtained calibration parameters.The steps are as follows:First,in accordance with the conversion relationship of the coordinate system in the calibration process,the calculation formula of the vertical distance from the camera light center to the reference plane and the calculation formula of the distance between the projector and the camera light center are given respectively.Secondly,according to the projector calibration principle,the position of the projector light axis perpendicular to the reference plane is gained by comparing the parallel relationship between the reference plane coordinate system and the projector coordinate system’s Z-axis.Then,in order to fulfill the position restriction that the line between the projector light center and the camera light center must be parallel to the reference plane,the camera’s spatial location is adjusted so that the vertical distance between it and the reference plane tends to that between the projector light center and the reference plane.And finally,the three-dimensional(3D)reconstruction of the target object can be finished using the phase height model’s system parameters once the aforementioned position limitations are put into practice.Experimental results demonstrate that the method improves the measurement accuracy,and verifies that it is effective and available in 3D shape measurement.

Measurement Method of Compressibility and Thermal Expansion Coefficients for Density Standard Liquid at 2329 kg/m^3 based on Hydrostatic Suspension Principle

The accurate measurement on the compressibility and thermal expansion coefficients of density standard liquid at 2329kg/m3（DSL-2329） plays an important role in the quality control for silicon single crystal manufacturing. A new method is developed based on hydrostatic suspension principle in order to determine the two coefficients with high measurement accuracy. Two silicon single crystal samples with known density are immersed into a sealed vessel full of DSL-2329. The density of liquid is adjusted with varying liquid temperature and static pressure, so that the hydrostatic suspension of two silicon single crystal samples is achieved. The compression and thermal expansion coefficients are then calculated by using the data of temperature and static pressure at the suspension state. One silicon single crystal sample can be suspended at different state, as long as the liquid temperature and static pressure function linearly according to a certain mathematical relationship. A hydrostatic suspension experimental system is devised with the maximal temperature control error ±50 μK; Silicon single crystal samples can be suspended by adapting the pressure following the PID method. By using the method based on hydrostatic suspension principle, the two key coefficients can be measured at the same time, and measurement precision can be improved due to avoiding the influence of liquid surface tension. This method was further validated experimentally, where the mixture of 1, 2, 3-tribromopropane and 1,2-dibromoethane is used as DSL-2329. The compressibility and thermal expansion coefficients were measured, as 8.5′10–4 K–1 and 5.4′10–10 Pa–1, respectively.

C_(2/3)经关节突经椎弓根螺钉固定的影像学测量及可行性分析

目的测量C_(2/3)经关节突经椎弓根螺钉相关影像学指标,并分析该置钉技术的可行性。方法收集120例全颈椎CT薄层扫描数据,其中男性75例,女性45例。设定C_(2/3)经关节突经椎弓根螺钉的进钉点,即进钉点在枢椎侧块的水平中线与中外1/3垂线交点处,螺钉自枢椎侧块穿C_(2/3)关节突关节、C_(3)侧块止于C_(3)椎弓根下缘。测量C_(2/3)经关节突经椎弓根螺钉相关影像学数据,包括C_(3)椎弓根宽度与高度,螺钉通道长度,内倾角度,头倾角度,最狭窄处宽度。并分析各项测量结果之间的关系。结果C_(3)椎弓根平均宽度5.48 mm,平均高度6.82 mm,螺钉通道平均长度18.68 mm,平均内倾角度20.46°,平均头倾角度50.1°,最狭窄处平均宽度2.80 mm。C_(3)椎弓根宽度与高度呈正相关(P=0.000),螺钉通道长度与C_(3)椎弓根宽度、高度呈正相关(P=0.000;P=0.000),螺钉通道最狭窄处宽度与C_(3)椎弓根宽度、高度呈正相关(P=0.000;P=0.000)。240例置钉测量数据中,如使用3.5 mm直径螺钉,均可完成置钉,C_(2/3)经关节突经椎弓根螺钉适用于所有患者。结论C_(2/3)经关节突经椎弓根螺钉在解剖学上是可行的,可作为上颈椎后路钉棒内固定补充的置钉技术。

Measurement on Physicochemical Properties ofNaCl-KCl-ScCl_3 System for Manufacture of Al-Sc Alloy by Molten Salt Electrolysis

The physicochemical properties of the system, such as density, surface tension, specific conductance and melting point were measured. The results were discussed.

MULTIPARAMETER MEASUREMENT FOR RACEWAY GROOVE OF BEARING BASED ON 3D RECONSTRUCTION WITH DIGITAL STRUCTURED LIGHT

A fast 3D reconstruction method based on structured light to measure various parameters of the raceway groove is presented. Digital parallel grating stripes distributed with sine density are projected onto the raceway groove by a DLP projector, and distorting of stripes is happened on the raceway. Simultaneously, aided by three-step phase-shifting approach, three images covered by different stripes are obtained by a high-resolution CCD camera at the same location, thus a more accuracy local topography can be obtained. And then the bearing is rotated on a high precision computer controlled rotational stage. Three images are also obtained as the former step at next planned location triggered by the motor. After one cycle, all images information is combined through the mosaics. As a result, the 3D information of raceway groove can be gained. Not only geometric properties but also surface flaws can be extracted by software. A preliminary hardware system has been built, with which some geometric parameters have been extracted from reconstructed local topography.

3-Dimensional Body Measurement Technology

3 - dimensional body measurement technology, the basis of developing high technology in industry, accelerates digital development of aplparel industry. This paper briefly introduces the history of 3 - dimensional body measurement technology, and recounts the principle and primary structure of some types of 3 - dimensional automatic body measurement system. With this understanding, it discusses prospect of 3- dimensional CAD and virtual technology used in apparel industry.

An Experimental System Development for Head Posture Estimation Based on 3-D Images Measurement

Although automobile is an indispensable vehicle to modern life, it also serves as a social problem with a big traffic accident. Among the reasons of traffic accidents, careless driving accounts for the largest part. So in order to avoid the careless driving, a system which can measure the posture of a driver and warns driver to drive carefully in the case of looking aside is necessary. Although the image measurement method is used broadly, there is a problem on which measurement accuracy is influenced by environment light, makeup of the driver, etc. in the general method based on the two-dimensional image. Therefore, in this study, we propose an image measurement method to obtain the head posture of driver. First we use three-dimensional measurement method which based on the infrared pattern projection to get 3-D information of head, and then we calculate the angle for faces. In this paper, we explain the composition method of an experiment system, and the results of head posture measurement experiment.

Fast Profilometry of 360° Spinning 3D Measurement

A technique of fast 360° spinning 3D measurement is realized.A laser diode used as light source produces 0.5 mm wide slit which is projected onto the surface of an object via a groupe of optical lenses.A CCD camera can grab the reflect curve line and its video output is processed by special hardware circuitries.Then the surface height value which the slit directs to will be directly obtained.The spinning table turns one degree each time and totally 360° 3D information acquisition need only 15 s.The result and conclusion are presented.

Accurate 3D geometry measurement for non-cooperative spacecraft with an unfocused light-field camera

This work explores an alternative 3D geometry measurement method for non-cooperative spacecraft guiding navigation and proximity operations.From one snapshot of an unfocused light-field camera, the 3D point cloud of a non-cooperative spacecraft can be calculated from sub-aperture images with the epipolar plane image(EPI) based light-field rendering algorithm.A Chang'e-3 model(7.2 cm×5.6 cm×7.0 cm) is tested to validate the proposed technique.Three measurement distances(1.0 m, 1.2 m, 1.5 m) are considered to simulate different approaching stages.Measuring errors are quantified by comparing the light-field camera data with a high precision commercial laser scanner.The mean error distance for the three cases are 0.837 mm, 0.743 mm, and 0.973 mm respectively, indicating that the method can well reconstruct 3D geometry of a non-cooperative spacecraft with a densely distributed 3D point cloud and is thus promising in space-related missions.

High Speed Laser 3D Measurement System

Using the method of line structure light produced by a laser diode,three dimensional profile measurement is deeply researched.A hardware circuit developed is used to get the center position of light section for the improvement of the measurement speed.A double CCD compensation technology is used to improve the measurement precision. An easy and effective calibration method of the least squares to fit the parameter of system structure is used to get the relative coordinate relationship of objects and images of light section in the directions of height and axis. Sensor scanning segment by segment and layer by layer makes the measurement range expand greatly.

A conoscopic holography-based 3D measurement system for analyzing defects in steel plate surface

A conoscopic holography-based 3D measurement system for analyzing the defects on the surface of steel plates was introduced in this paper. The hardware, which is automated through software, performs sampling of the steel plate surface. Through the software interface,point-cloud data of the steel plate surface are obtained and reconstructed to form a 3D image of the steel plate surface. The software allows automatic analysis of steel plate surface detects through identification of the bulges and depressions. In addition, the software can also automatically calculate the defect information ,such as the deepest point, volume, opening area, opening length, and so on, thereby determining the defect size. The results determined by this 3D measurement system were found to be in good agreement with the actual values.

The 3rd Asia-Pacfic Conference on Control and Measurement(APCCM’98)Will Be Held

The 3rd Asia-Pacfic Conference on Control and Measurement Sponsored by IEEE Shanghai Subsec-tion,Jiangsu Society of Aeronautics and Astronautics,Nanjing University of Aeronautics and Astronau-tics and the City University of Hong Kong will be held on August31 to September4,1998 in Dun-huang,China.APCCM Conference is the best chance for scholars,experts and engineers on control andmeasurement fields from the world to propose their academic insights,exchange their academic achieve-ments and enhance international cooperations.The purpose of of the APCCM’98 is to bring togetherscholars and experts engaging in control and measurement research to highlight new issues and contribu-tions of information technology for advances in industrial engineering.The topics of this conference arepresented as follows:control engineering,ideniification,modeling and system theory,specification andimplementation languages,controller synthesis,computer-aided design and simulation,algorithm anddeductive verification,fiber

Limits of Level 3 Fair Value Measurement： Based on Conceptual Framework

The IASB stated that in the review of the conceptual framework, if measurement uncertainty is very high, a measurement basis different from fair value may provide more appropriate information. Level 3 fair value measurements are inappropriate for areas （called ＂Level 4＂ by the author） in which models are not formulated and that have material uncertainty in measurement. The purpose of this paper is to elucidate ＂measurement uncertainty＂, which impacts ＂faithful representation＂ in fair value measurement, from the perspective of ＂verifiability＂. To do so, it will employ a conceptual examination of the limits of Level 3 fair value measurement based on IFRS 13 （Fair Value Measurement）. While taking into consideration recent discussions on reviewing conceptual framework, the author will reorganize the conceptual categories of verifiability （i.e., clarification of the ＂reasonable verifiability＂ categories） to underpin the fact that material uncertainties in measurement have obstructed constructing faithful representation. In addition, the author will discuss the problem that the dichotomy of direct and indirect found in IASB is not accurate enough to fully understand the concept of verifiability. In this context, the author will also suggest that the concept of verifiability, reorganized through ＂reasonable verifiability＂, can satisfy the requirements for constructing faithful representation.

Recognition of Multifunctional Coded Target in Single-camera Mobile 3D-vision Coordination Measurement

Single-camera mobile-vision coordinate measurement is one of the primary methods of 3D-coordinate vision measurement, and coded target plays an important role in this system. A multifunctional coded target and its recognition algorithm is developed, which can realize automatic match of feature points, calculation of camera initial exterior orientation and space scale factor constraint in measurement system. The uniqueness and scalability of coding are guaranteed by the rational arrangement of code bits. The recognition of coded targets is realized by cross-ratio invariance restriction, space coordinates transform of feature points based on spacial pose estimation algorithm, recognition of code bits and computation of coding values. The experiment results demonstrate the uniqueness of the coding form and the reliability of recognition.

^(3)He极化系统中FID NMR线圈的优化分析及实验验证

超极化^(3)He气体在中子极化、基础物理和诊断医学等领域广泛应用.测量其极化率对于^(3)He极化系统至关重要.通常使用自由感应衰减核磁共振(FID NMR)线圈来检测^(3)He原子的FID信号.线圈的测量信噪比与直径、匝数、以及其与气室的相对位置等因素相关.关于FID NMR线圈的优化分析,目前仅有少量的文献提及且缺乏详细的实验验证.本文通过对FID信号和线圈噪声的理论分析,建立了线圈测量信噪比模型,并且在基于亚稳态交换光泵(Metastability-Exchange Optical Pumping,MEOP)极化技术的^(3)He极化系统中对FID NMR线圈进行了实验验证.实验结果显示,在半径和高度均为r_(cell)的柱形气室中,线圈的测量信噪比在半径为r_(cell)/2时达到最优值,此结论与理论分析结果相符.该信噪比模型的相对误差不超过10%,证明了理论模型的有效性.这些研究结果对于优化设计^(3)He极化系统具有重要的指导意义.