Synergistic Coupling of Sulfide Electrolyte and Integrated 3D FeS_(2)Electrode Toward Long-Cycling All-Solid-State Lithium Batteries

FeS_(2)cathode is promising for all-solid-state lithium batteries due to its ultra-high capacity,low cost,and environmental friendliness.However,the poor performances,induced by limited electrode-electrolyte interface,severe volume expansion,and polysulfide shuttle,hinder the application of FeS_(2)in all-solid-state lithium batteries.Herein,an integrated 3D FeS_(2)electrode with full infiltration of Li6PS5Cl sulfide electrolytes is designed to address these challenges.Such a 3D integrated design not only achieves intimate and maximized interfacial contact between electrode and sulfide electrolytes,but also effectively buffers the inner volume change of FeS_(2)and completely eliminates the polysulfide shuttle through direct solid-solid conversion of Li2S/S.Besides,the vertical 3D arrays guarantee direct electron transport channels and horizontally shortened ion diffusion paths,endowing the integrated electrode with a remarkably reduced interfacial impedance and enhanced reaction kinetics.Benefiting from these synergies,the integrated all-solid-state lithium battery exhibits the largest reversible capacity(667 mAh g^(-1)),best rate performance,and highest capacity retention of 82%over 500 cycles at 0.1 C compared to both a liquid battery and non-integrated all-solid-state lithium battery.The cycling performance is among the best reported for FeS_(2)-based all-solid-state lithium batteries.This work presents an innovative synergistic strategy for designing long-cycling high-energy all-solid-state lithium batteries,which can be readily applied to other battery systems,such as lithium-sulfur batteries.

Fe(NO_3)_3·9H_2O/Fe(HSO_4)_3:An efficient reagent system for the oxidation of alcohols,thiols and sulfides in the absence of solvent

Fe（NO3）3-9H2O/Fe（HSO4）3 was used as an efficient reagent system for the oxidation of alcohols to their corresponding carbonyl compounds. All reactions were performed in the absence of solvent in good to high yields. Under the same reaction conditions, thiols and sulfides were also converted to their corresponding disulfides and sulfoxides, respectively. 2007 Farhad Shirini. Published by Elsevier B.V. on behalf of Chinese Chemical Society. All rights reserved.

Endogenous hydrogen sulfide and ERK1/2-STAT3 signaling pathway may participate in the association between homocysteine and hypertension

Background Homocysteine(Hcy)is a risk factor for hypertension,although the mechanisms are poorly understood.Methods We first explored the relationship between Hcy levels and blood pressure(BP)by analyzing the clinical data of primary hypertensive patients admitted to our hospital.Secondly,we explored a rat model to study the effect of Hcy on blood pressure and the role of H2S.An hyperhomocysteinemia(HHcy)rat model was induced to explore the effect of Hcy on blood pressure and the possible mechanism.We carried out tissue histology,extraction and examination of RNA and protein.Finally,we conducted cell experiments to determine a likely mechanism through renin-angiotensin-aldosterone system(RAAS)and extracellular signal-regulated kinase 1/2(ERK1/2)signaling pathway.Results In primary hypertensive inpatients with HHcy,blood pressure was significantly higher as compared with inpatient counterparts lacking HHcy.In the rat model,blood pressure of the Wistar rats was significantly increased with increases in serum Hcy levels and decreased after folate treatment.Angiotensin converting enzyme 1(ACE1)expression in the Wistar Hcy group was enhanced comparing to controls,but was decreased in the Wistar folate group.Angiotensin II receptor type 1(AGTR1)levels in the kidney tissue increased in the Wistar folate group.Both serum H2S and kidney cystathionineγ-lyase decreased with elevated levels of serum Hcy.In vitro,increased concentrations and treatment times for Hcy were associated with increased expression of collagen type 1 and AGTR1.This dose and time dependent response was also observed for p-STAT3 and p-ERK1/2 expression.Conclusion Endogenous H2S might mediate the process of altered blood pressure in response to changes in serum Hcy levels,in a process that is partly dependent on activated RAAS and ERK1/2-STAT3 signaling pathway.

Simultaneous catalytic hydrolysis of carbonyl sulfide and carbon disulfide over Al_2O_3-K/CAC catalyst at low temperature

In this work, a series of coal-based active carbon （CAC） catalysts loaded by A1203 were prepared by sol-gel method and used for the simulta- neous catalytic hydrolysis of carbonyl sulfide （COS） and carbon disulfide （CS2） at relatively low temperatures of 30-70 ℃. The influences of calcinations temperatures and operation conditions such as： reaction temperature, 02 concentration, gas hourly space velocity （GHSV） and relative humidity （RH） were also discussed respectively. The results showed that catalysts with 5.0 wt% A1203 calcined at 300 ℃ had supe- rior activity for the simultaneous catalytic hydrolysis of COS and CS2. When the reaction temperature was above 50 ℃, catalytic hydrolysis activity of COS could be enhanced but that of CS2 was inhibited. Too high RH could make the catalytic hydrolysis activities of COS and CS2 decrease. A small amount of 02 introduction could enhance the simultaneous catalytic hydrolysis activities of COS and CS2.

Selective and mild oxidation of sulfides to sulfoxides by H_2O_2 using DBUH-Br_3 as catalyst

DBUH-Br_3 catalyzed selective conversion of sulfides to sulfoxides in the presence of H_2O_2 as oxidizing agent is described.The reaction was performed selectively at room temperature and relatively short reaction times.

Stabilizing the MAPbI3 perovksite via the in-situ formed lead sulfide layer for efficient and robust solar cells

Surface passivation via post-treatment with organic reagents is a popular strategy to improve the stability and efficiency of perovskite solar cell. However, organic passivation still suffers from the weak bonding between organic chemicals and perovskite layers. Here we reported a facile inorganic layer passivating method containing strong Pb–S bonding by using ammonium sulfide treatment. A compact PbS_x layer was in-situ formed on the top surface of the perovskite film, which could passivate and protect the perovskite surface to enhance the performance and stability. Our novel inorganic passivation layer strategy demonstrates great potential for the development of high efficiency hybrid and robust perovskite optoelectronics.

Development of antimony sulfide–selenide Sb2(S,Se)3-based solar cells

Antimony sulfide–selenide Sb2（S,Se）3,including Sb2S3and Sb2Se3,can be regarded as binary metal chalcogenides semiconductors since Sb2S3and Sb2Se3are isomorphous.They possess abundant elemental storage,nontoxicity,good stability with regard to moisture at elevated temperatures and suitable physical parameters for light absorption materials in solar cells.To date,quite a few attempts have been conducted in the materials synthesis,photovoltaic property investigation and device fabrication.Benefiting from previous investigation in thin film solar cells and new generation nanostructured solar cells,this class of materials has been applied in either sensitized-architecture or planar heterojunction solar cells.Decent power conversion efficiencies from 5%to 7.5%have been achieved.Apparently,further improvement on the efficiency is required for future practical applications.To give an overview of this research field,this paper displays some typical researches regarding the methodologies toward the antimony sulfide–selenide synthesis,development of interfacial materials and device fabrications,during which we highlight some critical findings that promote the efficiency enhancement.Finally,this paper proposes some outstanding issue regarding fundamental understanding of the materials,some viewpoints for the efficiency improvement and their future challenges in solar cell applications.

In situ formed LiF-Li_(3)N interface layer enables ultra-stable sulfide electrolyte-based all-solid-state lithium batteries

Sulfide solid electrolytes are promising for high energy density and safety in all-solid-state batteries due to their high ionic conductivity and good mechanical properties.However,the application of sulfide solid electrolytes in all-solid-state batteries with lithium anode is restricted by the side reactions at lithium/electrolytes interfaces and the growth of lithium dendrite caused by nonuniform lithium deposition.Herein,a homogeneous LiF-Li_(3)N composite protective layer is in situ formed via a manipulated reaction of pentafluorobenzamide with Li metal.The LiF-Li_(3)N layer with both high interfacial energy and interfacial adhesion energy can synergistically suppress side reactions and inhibit the growth of lithium dendrite,achieving uniform deposition of lithium.The critical current densities of Li_(10)GeP_(2)S_(12)and Li_(6)PS_(5)Cl are increased to 3.25 and 1.25 mA cm^(-2)with Li@LiF-Li_(3)N layer,which are almost triple and twice as those of Li-symmetric cells in the absence of protection layer,respectively.Moreover,the Li@LiF-Li_(3)N/Li10GeP2S12/Li@LiF-Li_(3)N cell can stably cycle for 9000 h at 0.1 mA cm^(-2)under 0.1 mA h cm^(-2),and Li@LiF-Li_(3)N/Li_(6)PS_(5)Cl/Li@LiF-Li_(3)N cell achieves stable Li plating/stripping for 8000 h at 0.1 mA cm^(-2)under10 m A h cm^(-2).The improved dynamic stability of lithium plating/stripping in Li@LiF-Li_(3)N/Li_(10)GeP_(2)S_(12)or Li_(6)PS_(5)Cl interfaces is proved by three-electrode cells.As a result,LiCoO_(2)/electrolytes/Li@LiF-Li_(3)N batteries with Li_(10)GeP_(2)S_(12)and Li_(6)PS_(5)Cl exhibit remarkable cycling stability of 500 cycles with capacity retentions of 93.5%and 89.2%at 1 C,respectively.

Comparative study on the hydrogen storage performance of as-milled MgRENi rapid quenched alloy catalyzed by metal sulfides

The composites of Mg_(20)Pr_(1)Sm_(3)Y_(1)Ni_(10)as-quenched alloy and 3 wt.%M(M=CoS,CoS_(2),MoS_(2))catalyst were prepared by high-speed vibration ball mill.The effects of metal sulfides on the hydrogenation and dehydrogenation dynamics of alloys were compared.The results show that the as-milled composites contain a large number of amorphous embedded by a small amount of nanocrystals,and there are many point defects.After ball milling,the crystal grain size in the composites containing CoS is relatively larger,followed by CoS_(2)and MoS_(2)again.After hydrogenation,the amorphous phase is crystallized to form Mg_(2)NiH_(4),YH_(3),Pr_(8)H_(18.96),Sm_(3)H_7,Mg,Co or Mo phases,however,Mg_(2)Ni,YH_(2),PrH_(2)and Ni_(3)Y phases appeared after dehydrogenation.The maximum hydrogenation capacity of the composites containing CoS,CoS_(2)and MoS_(2)are 3.939,4.265 and 4.507 wt.%,respectively.The hydrogenation saturation ratio of composite containing MoS_(2)is higher than that of the composites containing CoS and CoS_(2).The dehydrogenation activation energy of the composites containing CoS,CoS_(2)and MoS_(2)is 107.76,68.43 and 63.28 kJ.mol^(-1).H_(2).On the improvement of hydrogen storage performance of Mg_(20)Pr_(1)Sm_(3)Y_(1)Ni_(10)alloy,the catalytic effect of MoS_(2)sulfide is better than that of CoS_(2)sulfide,and which is better than CoS sulfide.

A Facile Stereospecific Synthesis of 1, 3-Enynylsulfides via Sonogashira Coupling of （E）-a-Iodovinyl Sulfides with 1-Alkynes

（E）-α-Iodovinyl sulfides 1 underwent the Sonogashira coupling reactions with terminal alkynes 2 in piperidine at room temperature in the presence of 5 mol % of Pd（PPh3）4 and 10 mol % of CuI to afford the corresponding 1, 3-enynylsulfides 3 stereospecifically in high yields.

Sb_(2)S_(3)/石墨烯负极材料的制备及其储钠性能研究

钠离子电池(sodium-ion batteries,SIBs)具有成本低的潜在优势,有望成为替代锂离子电池(lithium ion batteries,LIBs)的储能设备。为提升钠离子电池的性能,开发出适应钠离子脱嵌的负极材料尤为重要。硫化锑(Sb_(2)S_(3))因其理论比容量高被认为是较好的钠离子电池负极材料。本文使用简单水热法将Sb_(2)S_(3)与石墨烯复合,制备Sb_(2)S_(3)/石墨烯复合材料(Sb_(2)S_(3)/Gr)。结果表明:Sb_(2)S_(3)/Gr作为钠离子电池负极时,不仅表现出良好的电导率(3.5×10~(-3)S/cm)和钠离子扩散速率(4.853×10~(-13)cm~2/s),而且在0.5 A/g的电流密度下,首圈库伦效率为76.27%,经150次循环后的比容量稳定在488 m A·h/g,表现出较高的比容量。Sb_(2)S_(3)/Gr复合材料表现出了极大的应用潜力,为高性能钠离子电池负极材料的研发提供了一定的参考价值。

Therapeutic importance of hydrogen sulfide in age-associated neurodegenerative diseases

Hydrogen sulfide(H2S)is a gasotransmitter that acts as an antioxidant and exhibits a wide variety of cytoprotective and physiological functions in age-associated diseases.One of the major causes of age-related diseases is oxidative stress.In recent years,the importance of H2S has become clear,although its antioxidant function has not yet been fully explored.The enzymes cystathionineβ-synthase,cystathionineγ-lya-se,and 3-mercaptopyruvate sulfurtransferase are involved in the enzymatic production of H2S.Previously,H2S was considered a neuromodulator,given its role in long-term hippocampal potentiation,but it is now also recognized as an antioxidant in age-related neurodegeneration.Due to aerobic metabolism,the central nervous system is vulnerable to oxidative stress in brain aging,resulting in age-associated degenerative diseases.H2S exerts its antioxidant effect by limiting free radical reactions through the activation of antioxidant enzymes,including superoxide dismutase,catalase,and glutathione peroxidase,which protect against the effects of aging by regulating apoptosis-related genes,including p53,Bax,and Bcl-2.This review explores the implications and mechanisms of H2S as an antioxidant in age-associated neurodegenerative diseases,including Alzheimer’s disease,Parkinson’s disease,Huntington’s disease,and Down syndrome.

Electrogenerative leaching of nickel sulfide concentrate with ferric chloride

In order to utilize the chemical energy in hydrometallurgical process of sulfide minerals reasonably and to simplify the purifying process, the electrogenerative process was applied and a dual cell system was introduced to investigate FeCl3 leaching of nickel sulfide concentrate. Some factors influencing the electrogenerative leaching, such as electrode structure, temperature and solution concentration were studied. The results show that a certain quantity of electrical energy accompanied with the leached products can be acquired in the electrogenerative leaching process. The output current and power increase with the addition of acetylene black to the electrode. Varying the components of electrode just affects the polarization degree of anode. Increasing FeCl3 concentration results in a sharp increase in the output of the leaching cell when c（FeCl3） is less than 0.1 mol/L. The optimum value of NaCl concentration for electrogenerative leaching nickel sulfide concentrate with FeCl3 is 3.0 mol/L. Temperature influences electrogenerative leaching by affecting anodic and cathodic polarization simultaneously. The apparent activation energy is determined to be 34.63 kJ/mol in the range of 298 K to 322 K. The leaching rate of Ni2+ is 29.3% after FeCl3 electrogenerative leaching of nickel sulfide concentrate for 620 min with a filter bag electrode.

Role of hydrogen sulfide in portal hypertension and esophagogastric junction vascular disease

AIM: To investigate the association between endogenous hydrogen sulfide (H2S) and portal hypertension as well as its effect on vascular smooth muscle cells.

Atomic-level insight of sulfidation-engineered Aurivillius-related Bi_(2)O_(2)SiO_(3) nanosheets enabling visible light low-concentration CO_(2) conversion

Unraveling atomic-level active sites of layered photocatalyst towards lowconcentration CO_(2) conversion is still challenging.Herein,the yield and selectivity of photocatalytic CO_(2) reduction of the Aurivillius-related oxide semiconductor Bi_(2)O_(2)SiO_(3) nanosheet(BOSO)were largely improved using a surface sulfidation strategy.The experiment and theoretical calculation confirmed that surface sulfidation of the Bi_(2)O_(2)SiO_(3) nanosheet(S-BOSO,6.28 nm)redistributed the charge-enriched Bi sites,extended the solar spectrum absorption to the whole visible range,and considerably enhanced the charge separation,in addition to creating new reaction active sites,as compared to pristine BOSO.Subsequently,surface sulfidation played a switchable role,wherein S-BOSO showed a very high CH_(3)OH generation rate(12.78μmol g^(-1) for 4 h,78.6%selectivity)from low-concentration CO_(2)(1000 ppm)under visible light irradiation,which outperforms most of the state-of-the-art photocatalysts under similar conditions.This study presents an atomic-level modification protocol for engineering reactive sites and charge behaviors to promote solar-to-energy conversion.

Thermoelectrical Investigation of Rare Earth Sulfide Materials

Results? are presented on synthesis?? and crystal growth of? Gd2S3-Dy2S3 solid solution sulfides and study of their thermoelectric properties in the range of temperatures 80-400 K. Gd0.2Dy0.8S1.48 composition has the best values of thermoelectric efficiency 0.39 x 10-3/K at 400 K.

Synthesis and Crystal Structure of a New Quaternary Sulfide FeSm6Si2S14

One new quaternary rare-earth sulfide, FeSm6Si2S（14）, has been synthesized by a facile solid-state route with boron as the reducing reagent. It crystallizes in the noncentrosymmetric hexagonal space group P63, belonging to the Ce6Al（3.33）S（14） structure-type, and the AxRE3MQ7 family. Its crystal structure features a 3-D framework constructed by SmS 8 bicapped trigonal prisms, where Fe and Si atoms occupy the octahedral（2a） and tetrahedral（2c） voids, respectively. The FeS 6 octahedra are connected with each other to form a chain along the b direction. FeSm6Si2S（14） represents a new chemical composition among the large family of AxRE3MQ7 compounds. The other related compounds containing transition metal are also discussed.

Fe_(3)O_(4)/CuCo_(2)S_(4)复合物活化过硫酸一氢盐对有机染料的去除作用

采用水热法制备了Fe_(3)O_(4)/CuCo_(2)S_(4)复合催化剂,利用SEM、XRD、EDS对0.25-Fe_(3)O_(4)/CuCo_(2)S_(4)复合材料的表面形貌和结构进行表征,研究了复合催化剂活化PMS降解染料废水的效能。实验结果显示,在室温条件下,加入200 mg/L PMS、125 mg/L催化剂,20 mg/L RhB在40 min内去除率达到99.5%。自由基淬灭实验表明,Fe_(3)O_(4)/CuCo_(2)S_(4)活化PMS产生的羟基自由基、硫酸根自由基和单线态氧等活性物质均参与了RhB降解过程。回收实验表明,4次循环使用后RhB的降解率仍能达到94.2%,表明Fe_(3)O_(4)/CuCo_(2)S_(4)复合催化剂具有良好的可重复利用性和优异的催化活性,易于回收。Fe_(3)O_(4)/CuCo_(2)S_(4)可用于有机物水污染的处理。

BiOIO_(3)/ZnIn_(2)S_(4)复合催化剂的制备及其光还原六价铬的性能

采用水热法制备BiOIO_(3)/硫铟化物复合催化剂,并将其用于水体中Cr(Ⅵ)的去除,研究结果显示:与其他复合材料相比,所制备的BiOIO_(3)/ZnIn_(2)S_(4)对Cr(Ⅵ)具有最佳的光催化活性。而后考察了反应时间、污染物初始浓度、催化剂用量等实验条件对Cr(Ⅵ)去除率的影响。为光催化还原Cr(Ⅵ)的实际应用提供了理论依据。

泥蚶TLR3基因的生物学特性及表达分析

为探究泥蚶Toll样受体3(TLR3)基因的生物学特性及其对缺氧和硫化物胁迫的响应,克隆了泥蚶TgTLR3核心片段序列,并运用实时荧光定量PCR技术检测了TgTLR3基因在血淋巴、鳃、肝胰腺、外套膜、闭壳肌、斧足等组织的分布情况以及在缺氧和硫化物胁迫下血淋巴中的表达模式。结果显示,泥蚶TgTLR3开放阅读框2634 bp,编码877个氨基酸。其中,49~593位为胞外富含亮氨酸重复序列,跨膜域为658~680位,720~865位为白细胞介素受体1结构域,蛋白质分子量为99.4 kD,等电点为7.76。氨基酸同源性比对发现,泥蚶TgTLR3氨基酸序列与毛蚶相似度高达80.05%。系统进化树显示,TgTLR3与毛蚶首先聚为一支,表明与毛蚶亲缘关系最近。TgTLR3在泥蚶各组织中均有表达,其中血淋巴表达量最高。缺氧胁迫48~96 h后,血淋巴中TgTLR3显著升高;添加硫化物后,TgTLR3在48 h显著低于缺氧组但在96 h仍显著高于对照。上述研究结果表明,TgTLR3基因在泥蚶应对缺氧和硫化物胁迫的免疫调控中可能发挥着重要作用。研究结果为探究软体动物TLR3的功能及其响应缺氧及硫化物胁迫的免疫机制提供了基础数据。