Microstructure and mechanical properties of laser welded joints of pure copper and 304 stainless steels

A continuous wave diode laser with an output power of 2.8 kW was used to join pure copper and 304 stainless steel with a thickness of 1 mm. The focused laser beam with a diameter of O. 8 mm was irradiated on the copper side of the butt joints. In process of laser welding, effects of processing primary parameters on tensile strength of the joints were investigated. The interfacial characterizations of the joints were investigated by metallographic microscope, scanning electron microscope （SEM） and energy dispersive X-ray spectroscope （EDS）. The results showed that the element diffusion and solution occur and metallurgical bonding was achieved between pure copper and 304 stainless steel. The maximum tensile strength of the joints was 209 MPa when the laser power of welding was 2. 4 kW and welding speed was 12 mm/s.

Effects of Laser Shock Processing on Mechanical Properties of Laser Welded ANSI 304 Stainless Steel Joint

With the rapid development of engineering component with integration,high-speed and multi-parameter,traditional techniques haven＇t met practical needs in extreme service environment.Laser welding,a new welding technology,has been widely used.However,it would generate the drop of mechanical properties for laser welded joint due to its thermal effect.Laser shock processing（LSP） is one of the most effective methods to improve the mechanical properties of laser welded ANSI 304 stainless steel joint.In this paper,the effects of LSP on the mechanical properties of laser welded ANSI 304 stainless steel joint have been investigated.The welded joint on the front of the tensile samples is treated by LSP impacts,and the overlapping rate of the laser spot is 50%.The tensile test of the laser welded joint with and without LSP impacts is carried out,and the fracture morphology of the tensile samples is analyzed by scanning electron microscope（SEM）.Compared with the yield strength of 11.70 kN,the tensile strength of 37.66 kN,the yield-to-tensile strength ratio of 0.310 7,the elongation of 25.20%,the area reduction of 32.68% and the elastic modulus of 13 063.876 MPa,the corresponding values after LSP impacts are 14.25 kN,38.74 kN,0.367 8,26.58%,42.29% and 14 754.394 MPa,respectively.Through LSP impacts,the increasing ratio of the yield strength and tensile strength are 121.79% and 102.87%,respectively;the elongation and area reduction are improved by 5.48% and 29.38%,respectively.By comparing with coarse fracture surface of the welded joint,the delamination splitting with some cracks in the sharp corner of the welded joint and asymmetric dimples,LSP can cause brighter fracture surface,and finer and more uniform dimples.Finally,the schematic illustration of dimple formation with LSP is clearly described.The proposed research ensures that the LSP technology can clearly improve the yield strength,tensile strength,yield-to-tensile strength ratio,elongation,area reduction and elastic modulus of the welded joint.The enhancement mechanism of LSP on laser welded ANSI 304 stainless steel joint is mainly due to the fact that the refined and uniform dimples effectively delay the fracture of laser welded joints.

Investigation of SUS304 Stainless Steel with Warm Hydro-mechanical Deep Drawing

Basing on warm mechanical property of SUS304 stainless steel and hydro-mechanical deep drawing process, warm hydro-mechanical deep drawing process is proposed and discussed with experiments in this paper. The experiments are performed at four different temperatures. The results show that the formability of stainless steel is improved under the condition of warm temperature. Warm hydro-mechanical deep drawing raises limiting drawing ratio of SUS304 effectively, and limiting drawing ratio 3.3 is obtained, which is beyond 2.0 with conventional deep drawing. The temperature of 90℃ is beneficial to the forming of SUS304 stainless steel, the strain-induced martensite is controlled effectively, and the thickness distribution is more uniform.

Static and dynamic finite element analysis of 304 stainless steel rod and wire hot continuous rolling process

Three-dimensional finite element models were developed to analyze 304 stainless steel rod and wire hot continuous rolling process with the help of MSC.Marc software. The entire 30-pass deformation process and the actual parameters of production line were taken into account. Static and dynamic procedures were used to study the continuous rolling process with the aid of the thermo-mechanical coupled FEM of elastic-plasticity. The properties of billets, such as deformation, temperature field and rolling force, were mainly discussed. The simulation results of temperature agree well with the measured values. Comparisons of the analysis results obtained using static implicit method and dynamic implicit method were presented. It is shown that static implicit procedure is more accurate than dynamic implicit procedure and is able to simulate the rolling process with a lower speed, such as a roughing mill. Whereas, dynamic analysis shows a higher efficiency than static analysis and is fit for simulating the rolling process with a higher speed, such as a finishing mill.

Uniaxial Time-Dependent Ratcheting of SS304 Stainless Steel at High Temperatures

The uniaxial time-dependent strain cyclic behaviors and ratcheting of SS304 stainless steel were studied at high temperatures （350 ℃ and 700 ℃）. The effects of straining and stressing rates, holding time at the peak and/or valley of each cycle in addition to ambient temperature on the cyclic softening/hardening behavior and ratcheting of the material were discussed. It can be seen from experimental results that the material presents remarkable time dependence at 700 ℃, and the ratcheting strain depends greatly on the stressing rate, holding time and ambient temperature. Some significant conclusions are obtained, which are useful to build a constitutive model describiog the time-dependent cyclic deformation of the material.

HOT DUCTILITY OF 304HC STAINLESS STEEL AND THE MODEL OF RESISTANCE TO DEFORMATION

The ductility map of 304HC stainless was determined by using the Gleeble-1500 dynamic thermal-mechanical simulator. The effect of Cu on the hot ductility of 304HC stainless steel was analyzed and the mathematical model of resistance to deformation was established. The microstructure, inclusion and fracture surface were studied by using the method of micro structure analysis, scanning, energy spectrum and electron microscope. The results show that Cu has effect on the hot ductility, and the hot ductility of 304HC stainless steel decrease with the increase of content of Cu. The deformation temperature also has much effect on the hot ductility, the suitable deformation temperature are 1100-1200℃. The reason of it is that the Cu rich chemical compounds were precipitated from austenite phase during cooling. The Cu rich chemical compounds are brittle substance such as Cu2S, Cu2O and ε-Cu etc.

Effect of W/Cu composite filler metals on the microstructure and mechanical properties of laser welded pure niobium/304 stainless steel joint

Cracking in a laser weld of niobium to stainless steel occurred due to the formation of brittle,continuously distributed Nb-Fe intermetallic compounds.A crack-free joint,which had a tensile strength of 147 MPa,was obtained by using the W/Cu composite filler metals.To determine the reasons for cracking in the Nb/SS joint and the function of the W/Cu composite filler metals on the improvement of the cracking resistance of the Nb/W/Cu/SS joint,the microstructures of the joints were studied by optical microscopy,scanning electron microscopy and X-ray diffraction.The cracking susceptibilities of the joints were evaluated with microhardness test on the cross section of the Nb/W/Cu/SS joint.The results showed that the Nb/W/Cu/SS joint was characterized by various solid solution.The formation of solid solution reduced the cracking susceptibility of the joint.

Study on numerical simulation of TA1-304 stainless steel explosive welding

In order to guide the explosive welding experiment of titanium-stainless steel,Three-dimensional numerical simulation of explosive welding,which select TA1 as flyer plate and 304 stainless steel as base plate,is carried out by using the LS-DYNA software and SPH-FEM coupling algorithm in the present study.The explosive welding window is calculated and established.It is found that the numerical simulation results are in good agreement with the experimental results.The displacement,velocity and pressure-time curves of characteristic elements show that the quality of explosive welding composites is superior.It is proved that SPH-FEM coupling algorithm is effective for explosive welding of TA1/304 stainless steel and can effectively guide the selection of explosive welding parameters.

Fractal Characteristic of Pits Distribution on 304 Stainless Steel Corroded Surface and Its Application in Corrosion Diagnosis

Electrochemical techniques and fractal theory were employed to study the corrosion behaviors and pits distribution characteristics on the corroded surfaces of 304 stainless steel exposed in FeCl3 solution. Fractal features of pits distribution over the corroded surfaces were observed and described by the fractal dimension. A 5-8-2 back-propagation （BP） artificial neural network model for the diagnoses of the pitting corrosion rate and pits deepness of 304 stainless steel under various conditions was developed by considering the fractal dimension as a key parameter for describing the pitting corrosion characteristics. The predicted results are well in agreement with the experimental data of pitting corrosion rate and pit deepness. The max relative errors between their experimental and simulation data are 6.69% and 4.62%, respectively.

Microstructure and corrosion resistance of 304 stainless steel electroslag strip cladding

The 304 stainless steel strips were deposited one layer on carbon steel base metal by electroslag strip cladding （ESC） and submerged arc cladding （SAC）, respectively. The solidification microstrueture of ESC metal was analyzed by the optical microscopy, scanning electron microscope and energy dispersive spectroscopy. The corrosion resistance studies of strip cladding metals were carried out in 10% oxalic acid electrolytic etching test. The results showed that the cladding metal obtained by ESC presented low content of C, high content of Cr and enough alloying element of Ni in the chemical composition. The transition zone of ESC with small width was almost parallel with the base metal, leading to a lower dilution. There are three types of solidification modes （ A→AF→FA ） occurred in the ESC metal due to the decrease of cooling rate and degree of dilution from the transition zone to the top of ESC metal. As a result, the microstructure of ESC metal exhibited mainly austenite with a small amount of ferrite, contributing to achievement of better corrosion resistance.

Deformation Behavior and Formability of Gradient Nano-grained AISI 304 Stainless Steel Processed by Ultrasonic Impact Treatment

The deformation behavior and formability of gradient nano-grained（GNG） AISI 304 stainless steel in uniaxial and biaxial states were investigated by means of tensile test and small punch test（SPT）. The GNG top layer was fabricated on coarse grains（CG） AISI 304 by ultrasonic impact treatment. The results showed that the CG substrate could effectively suppress the strain localization of NC in GNG layer, and an approximate linear relationship existed between the thickness of substrate（h） and uniform true strain before necking（ε_（unif））. Grain growth of NC was observed at the stress state with high Stress triaxiality T, which led to better ductility of GNG/CG 304 in SPT, as well as similar true strain after the onset of necking（ε_（neck）） compared with coarse 304 in tensile test. Ei-values of GNG/CG 304 with different structures were nearly the same at different punch speeds, and good formability of GNG/CG 304 was demonstrated. However, punch speed and microstructure needed to be optimized to avoid much lost of membrane strain region in biaxial stress state.

1-Hydroxyethylidene-1,1-diphosphonic Acid (HEDP) as a Corrosion Inhibitor of AISI 304 Stainless Steel in a Medium Containing Chloride and Sulfide Ions in the Presence of Different Metallic Cations

The novelty of this paper is the analysis in a medium containing sulfide ion due to the generation of this ion in petroleum industries, in the refining stage (the sulfide ion is also present on the produced water). The performance of 1-hydroxyethylidene-1,1-diphosphonic acid inhibitor (HEDP) was investigated by potentiodynamic polarization, electrochemical impedance spectroscopy, and weight loss measurements in a dissolution of AISI 304 stainless steel immersed in a solution containing chloride and sulfide ions. The protection of the stainless was increased with the addition of divalent cations (Ca2+, Zn2+, and Mg2+). Potentiodynamic polarization studies have shown that the inhibitor alone has anodic protection, but the addition of Ca2+ (10 mg·L-1) favors the cathodic protection, and the addition of Zn2+ (20 mg·L-1) and Mg2+ (10 mg·L-1) mixed-type is observed. Electrochemical impedance spectroscopy was performed at three distinct potentials: -0.3 [V vs. SCE], Ecorr [V vs. SCE], and 0.1 [V vs. SCE]. This revealed that calcium is responsible for favoring the formation of the film and the other elements (zinc and magnesium) favor the stabilization of the protective film. Scanning electron microscopy analysis revealed that the addition of cations provided the adsorption of HEDP on the metal surface. Weight loss results showed that the presence of zinc in a solution containing HEDP favored greater inhibitor efficiency (Zn2+ ηm = 85.2% and for Mg2+ ηm = 70.4%).

Residual stress in the cylindrical drawing cup of SUS304 stainless steel evaluated by split-ring test

The residual stresses in the wall of a SUS304 stainless steel cylindrical drawing cup were evaluated by split-ring tests, and the influences of stamping die parame- ters on the residual stress were investigated. A new theoretical model of a split-ring test was developed to evaluate the resid- ual stress in a ring, which was verified to be reasonable and reliable by numerical simulations with ABAQUS code and by nanoindentation tests. Seven groups of split-ring tests were completed, and the residual stresses were calculated according to the theoretical model. The split-ring test results showed that the circumferential residual stress in the wall of the SUS304 stainless steel cylindrical drawing cup was very large and did not change with the different die comer radius. The circumferential residual stress first increased with the increase of drawing punch-die clearance, then was almost unchanged when the clearance increased greater than blank thickness 1 mm. Thus, a smaller clearance was suggested to be chosen to reduce the residual stress in the wall of the SUS304 stainless steel drawing cup.

EFFECT OF COPPER ON THE HOT PLASTICITY OF 304HC STAINLESS STEEL

The plasticity map of 304HC stainless steel was determined by using tensile and compressive test. The effect of Cu on the hot plasticity of 304HC stainless steel was analyzed. The microstructure, inclusion and fracture surface were studied by using the method of optical microscopy, SEM, EDS and EPMA. The results showed that Cu has effect on the hot plasticity and the hot plasticity of 304HC stainless steel decrease with the increase of Cu content. The deformation temperature also has much effect on the hot plasticity, the suitable deformation temperature are 1100-1200℃. The reason is that the brittle compounds were precipitated from austenite during cooling. These brittle compounds are Cu2S, Cu2O and PbCI etc.

Investigation on the Hydro-forming of SUS304 Stainless Steel Dome

The dome hydro-forming was studied theoretically and experimentally. The theoretical analysis shows that the process of dome hydro-forming can be divided into two stages, i.e., firstly forming a hemi-sphere and secondly forming a hemi-toroidal. Theoretically, being larger than those in the outer area of a hemi-toroidal shell, the radial tensile stresses take place in the inner area where fracture is more likely to occur in the forming process. The required hydraulic pressure to form the dome should be determined by the deformation in the outer area, hitting about 12 MPa in theory. The experimental results show that the dome could be produced in one operation by hydro-forming which needs a hydraulic pressure of about 9 MPa. The experimental results prove to agree well with the theoretical analysis. In order to avoid wrinkling and fracture, the closing force acted on the die should be adjusted properly in accordance with the hvdraulic nressure.

A multi-scale grained microstructure of the surface nanocrystallized 304 stainless steel sheets after warm-rolling

An ultrafine grained microstructure was obtained for 304 stainless steel(304SS)sheets by using surface nanocrystallization and warm-rolling.The microstructure and mechanical properties were determined by X-ray diffraction(XRD),transmission electron microscope(TEM)and a test on microhardness.Experimental results were shown that the microstructure was featured by a continuous distribution from the nanocrystalline on the surface to micro-grains in the center,in which the volume fraction of the micro-sized grains is about 40% in the surface layer.This multi-scale grained microstructure was composed of austenite and martensite phases with a gradient increasing volume fraction of austenite from the surface to the centre.The microhardness of the resultant steel was higher than 150% of that as received,due to the refined grains and strain-induced martensitic transformation.The hardness distribution was consistent with the microstructural variation,suggesting a good combination of high strength and improved ductility.

Influence of the preheated substrate temperature on the microstructure deposition behavior of the 304 stainless steel coatings deposited by cold gas dynamic spraying

The effects of the substrate temperature on the deposition and microstructure of the 304 stainless steel （SS） cold gas dynamic spraying （CGDS） coatings were investigated. It was found that the higher substrate temperature could increase the deposition rate of the 304 SS particles,even the oxide films existed at the interface. There was a critical oxide film with a thickness of 3 -4 um which could be destroyed by the impacted particles. The micro-hardness and microstructure of the 304 SS coatings under different substrate preheating temperatures were almost the same.

Determination of plastic equation of state by indentation method on 304 stainless steel

An indentation method for determining the plastic mechanical equation of state (PES) was studied. The constant loading rate and constant loading rate/load indentation tests were carried out. The method for determining the work-hardening coefficient and the strain rate sensitivity coefficient of PES were discussed in detail. 304 stainless steel hot-treated at 1100°C was used to verify the method. The work-hardening coefficient and strain rate sensitivity coefficient of 304 stainless steel were respectively determined as 0.30 and 0.015. These values are very close to those achieved by tensile tests. From the establishment of the PES of 304 stainless steel it is shown that the PES obtained by the indentation method is easier than that by the tensile test.

Fatigue Response of Cold-Rolled Type-304 Stainless Steel Foil

This study presents the fatigue response of 304 stainless steel foil, cold-rolled to a thickness of 3.2 μm with 87 percent cold work at orientations of 0, 45, and 90 degrees to the direction of rolling. Fatigue specimens were fabricated by laminating a supportive layer of 20-μm polyimide film to one side of the foil and patterning 242 crack initiation features by photolithographic process. Progression of fatigue damage was determined through electrical resistance measurement. The fatigue response was demonstrated to be largely affected by anisotropy existing between the rolling direction and the off-axis orientations. Fatigue cracks that traveled in a direction parallel to the elongated grains (cyclic loads applied at 90-degree orientation to foil rolling direction) had the most fatigue response (undesirable characteristic). The construction of the specimens with thin foil supported by a film backing contributed to high fatigue threshold.

Characterization of Dissimilar Welding between 304 Stainless Steel and Gray Iron Using Nickel Coated Electrode

This paper presents the study carried out to study the microstructure and mechanical properties of AISI 304 stainless steel and gray iron, in order to recognize the effect of welding parameters on the joint. The shielded metal arc welding technique was applied with a 3.2 mm diameter nickel coated electrode under preheating and post heat conditions at 350°C. Vickers hardness test and metallographic analysis were carried out at the heat affected zone and at the interface to determine the effect on mechanical and metallurgical characteristics. Vickers hardness differences among joint areas were directly related to microstructural changes. There are no significant differences in AISI 304 hardness, but the hardness increased at the heat affected zone and decreased at the filler metal. Grey iron hardness at the heat affected zone was even lower and more slightly superior than grey iron hardness.