In this paper, near-fault strong ground motions caused by a surface rupture fault (SRF) and a buried fault (BF) are numerically simulated and compared by using a time-space-decoupled, explicit finite element metho...In this paper, near-fault strong ground motions caused by a surface rupture fault (SRF) and a buried fault (BF) are numerically simulated and compared by using a time-space-decoupled, explicit finite element method combined with a multi-transmitting formula (MTF) of an artificial boundary. Prior to the comparison, verification of the explicit element method and the MTF is conducted. The comparison results show that the final dislocation of the SRF is larger than the BF for the same stress drop on the fault plane. The maximum final dislocation occurs on the fault upper line for the SRF; however, for the BE the maximum final dislocation is located on the fault central part. Meanwhile, the PGA, PGV and PGD of long period ground motions (≤ 1 Hz) generated by the SRF are much higher than those of the BF in the near-fault region. The peak value of the velocity pulse generated by the SRF is also higher than the BE Furthermore, it is found that in a very narrow region along the fault trace, ground motions caused by the SRF are much higher than by the BF. These results may explain why SRFs almost always cause heavy damage in near-fault regions compared to buried faults.展开更多
Objective To investigate the effect of computer aided 3D simulation technique for treating complicated foot and ankle fractures precisely.Methods From November 2007 to August 2009,255 patients with complicated foot an...Objective To investigate the effect of computer aided 3D simulation technique for treating complicated foot and ankle fractures precisely.Methods From November 2007 to August 2009,255 patients with complicated foot and ankle fractures展开更多
The numerical simulation of internal features,such as inclusions and voids,is important to analyze their impact on the performance of composite materials.However,the complex geometries of internal features and the ind...The numerical simulation of internal features,such as inclusions and voids,is important to analyze their impact on the performance of composite materials.However,the complex geometries of internal features and the induced continuous-discontinuous(C-D)deformation fields are challenges to their numerical simulation.In this study,a 3D approach using a simple mesh to simulate irregular internal geometries is developed for the first time.With the help of a developed voxel crack model,image models that are efficient when recording complex geometries are directly imported into the simulation.Surface reconstructions,which are usually labor-intensive,are excluded from this approach.Moreover,using image models as the geometric input,image processing techniques are applied to detect material interfaces and develop contact pairs.Then,the C-D deformations of the complex internal features are directly calculated based on the numerical manifold method.The accuracy and convergence of the developed3D approach are examined based on multiple benchmarks.Successful 3D C-D simulation of sandstones with naturally formed complex microfeatures demonstrates the capability of the developed approach.展开更多
With the development of aviation agricultural technology,the number of farmers adopting the use of drones in daily agricultural activities is growing rapidly in recent decades.Among these,a large portion constitutes a...With the development of aviation agricultural technology,the number of farmers adopting the use of drones in daily agricultural activities is growing rapidly in recent decades.Among these,a large portion constitutes agricultural drones being used in pest control and crop protection practices,e.g.agriculture spraying of pesticides.Spraying pesticides with drones have proven to be faster than other traditional methods.On the downside,flight time and range of Unmanned Aerial Vehicles(UAV)are often limited.Thus,a proper arrangement of flight height and velocity will greatly improve spraying efficiency.A new strategy to optimize the flight parameters,i.e.flight height and flight velocity,for fixed-wing UAV with a 3D simulation-based approach together with an automatic optimization algorithm was proposed in this study.To find the optimal parameters for a UAV to fly and spray under certain environmental conditions,a three-dimensional model of the target crop was established first,followed by a detailed simulation of droplet spraying.As a demonstration case,a grass model was developed and used as the target plant,and a physics-based method was used to simulate realistically the movement of the droplets in the air as well as the interaction between the droplets and the plant to obtain the droplet deposition rate under the specified operating parameters.Furthermore,the standard Particle Swarm Optimization(PSO)algorithm was used to optimize the UAV operating parameters to obtain the best operating parameters.The results indicate that using the standard PSO algorithm to optimize the operating parameters of the drone could significantly improve the deposition rate and find the best operating parameters.展开更多
The standard three dimensional(3D) k-ε turbulence model was applied to simulate the flow field of a small scale combined oxidation ditch. The moving mesh approach was used to model the rotor of the ditch. Compariso...The standard three dimensional(3D) k-ε turbulence model was applied to simulate the flow field of a small scale combined oxidation ditch. The moving mesh approach was used to model the rotor of the ditch. Comparison of the computed and the measured data is acceptable. A vertical reverse flow zone in the ditch was found, and it played a very important role in the ditch flow behavior. The flow pattern in the ditch is discussed in detail, and approaches are suggested to improve the hydrodynamic performance in the ditch.展开更多
Minimally invasive surgery is an important technique used for cytopathological examination.Recently,multiple studies have been conducted on a three-dimensional(3D)puncture simulation model as it can reveal the interna...Minimally invasive surgery is an important technique used for cytopathological examination.Recently,multiple studies have been conducted on a three-dimensional(3D)puncture simulation model as it can reveal the internal deformation state of the tissue at the micro level.In this study,a viscoelastic constitutive equation suitable for muscle tissue was derived.Additionally,a method was developed to define the fracture characteristics of muscle tissue material during the simulation process.The fracture of the muscle tissue in contact with the puncture needle was simulated using the cohesive zone model and a 3D puncture finite element model was established to analyze the deformation of the muscle tissue.The stress nephogram and reaction force under different parameters were compared and analyzed to study the deformation of the biological soft tissue and guide the actual operation process and reduce pain.展开更多
This paper presents a new approach to parallelize 3D lattice Monte Carlo algorithms used in the numerical simulation of polymer on ZiQiang 2000 a cluster of symmetric multiprocessors (SMPs). The combined load for cel...This paper presents a new approach to parallelize 3D lattice Monte Carlo algorithms used in the numerical simulation of polymer on ZiQiang 2000 a cluster of symmetric multiprocessors (SMPs). The combined load for cell and energy calculations over the time step is balanced together to form a single spatial decomposition. Basic aspects and strategies of running Monte Carlo calculations on parallel computers are studied. Different steps involved in porting the software on a parallel architecture based on ZiQiang 2000 running under Linux and MPI are described briefly. It is found that parallelization becomes more advantageous when either the lattice is very large or the model contains many cells and chains.展开更多
Weft knitted fancy fabrics are widely used in knitted garment design. Due to the complexity of the structures, their modeling and simulation needs to be solved in three-dimensional (3D) CAD developments. In this paper...Weft knitted fancy fabrics are widely used in knitted garment design. Due to the complexity of the structures, their modeling and simulation needs to be solved in three-dimensional (3D) CAD developments. In this paper, 3D loop geometrical models of weft knitted fancy structures, including tuck stitch, jacquard stitch, transfer stitch and fleecy stitch, were developed based on an improved model of plain loop, and their central axes as some 3D space curves were achieved by using Non-Uniform Rational B-Splines (NURBS). The 3D visual simulation programme was written in C++ programming language using OpenGL, which was a function library of 3D graphics. Some examples of weft knitted fancy fabrics were generated and practical application of 3D simulation was discussed.展开更多
When heavy machines and large scaled receiver system of communication equipment are manufactured, it always needs to produce large-sized steel castings, aluminum castings and etc. Some defects of hot cracking by therm...When heavy machines and large scaled receiver system of communication equipment are manufactured, it always needs to produce large-sized steel castings, aluminum castings and etc. Some defects of hot cracking by thermal stress often appear during solidification process as these castings are produced, which results in failure of castings. Therefore predicting the effects of technological parameters for production of castings on the thermal stress during solidification process becomes an important means. In this paper, the mathematical models have been established and numerical calculation of temperature fields by using finite difference method (FDM) and then thermal stress fields by using finite element method (FEM) during solidification process of castings have been carried out. The technological parameters of production have been optimized by the results of calculation and the defects of hot cracking have been eliminated. Modeling and simulation of 3D thermal stress during solidification processes of large-sized castings provided a scientific basis, which promoted further development of advanced manufacturing technique.展开更多
Mountainous regions have disadvantages in economic development because of harsh physical and climatic conditions.However,winter tourism activities are one of the key components for supporting economic development in t...Mountainous regions have disadvantages in economic development because of harsh physical and climatic conditions.However,winter tourism activities are one of the key components for supporting economic development in the highlands.Establishing a ski resort area supports direct and indirect employment in a region,and it stops immigration from mountainous regions to other places.This research aimed to assess the potential ski areas using a multi criteria evaluation technique in the Van region which is located in the eastern part of Türkiye.In this context,snow cover duration,sun effect,slope,slope length,elevation,population density,distance from main roads and lake visibility were used as input factors in the decision making process.Each factor was standardized using a fuzzy technique based on existing well-known ski centers in Türkiye.The weight of inputs was defined by applying a survey to the professional skiers.The most important factors were detected as transportation opportunities and snow covers whereas,the least important factors were elevation and population density.Additionally,lake visibility was very important to make a difference from other existing facilities in the region.Therefore,it was included as constraints and lake visible areas were extracted at the final stage of the research.Potential ski areas were mapped in three levels as professional,intermediate and beginner skiers.One of the suitable areas was selected as a sample projection and for the 3D simulation of the ski investment area.Potential costs and benefits were discussed.It was found that a ski tourism area investment can be amortized in 3 years in the region.展开更多
The fabrication process dependent effects on single event effects (SEEs) are investigated in a commercial silicon- germanium heterojunction bipolar transistor (SiGe HBT) using three-dimensional (3D) TCAD simulat...The fabrication process dependent effects on single event effects (SEEs) are investigated in a commercial silicon- germanium heterojunction bipolar transistor (SiGe HBT) using three-dimensional (3D) TCAD simulations. The influences of device structure and doping concentration on SEEs are discussed via analysis of current transient and charge collection induced by ions strike. The results show that the SEEs representation of current transient is different from representation of the charge collection for the same process parameters. To be specific, the area of C/S junction is the key parameter that affects charge collection of SEE. Both current transient and charge collection are dependent on the doping of collector and substrate. The base doping slightly influences transient currents of base, emitter, and collector terminals. However, the SEEs of SiGe HBT are hardly affected by the doping of epitaxial base and the content of Ge.展开更多
Airblasts,as one common phenomenon accompanied by rapid movements of landslides or rock/snow avalanches,commonly result in catastrophic damages and are attracting more and more scientific attention.To quantitatively a...Airblasts,as one common phenomenon accompanied by rapid movements of landslides or rock/snow avalanches,commonly result in catastrophic damages and are attracting more and more scientific attention.To quantitatively analyze the intensity of airblast initiated by landslides,the Wangjiayan landslide,occurred in the Wenchuan earthquake,is selected here with the landslide propagation and airblast evolution being studied using FLUENT by introducing the Voellmy rheological law.The results reveal that:(1)For the Wangjiayan landslide,its whole travelling duration is only 12 s with its maximum velocity reaching 36 m/s at t=10 s;(2)corresponding to the landslide propagation,the maximum velocity,28 m/s,of the airblast initiated by the landslide also appears at t=10 s with its maximum pressure reaching594.8 Pa,which is equivalent to violent storm;(3)under the attack of airblast,the load suffered by buildings in the airblast zone increases to 1300 Pa at t=9.4 s and sharply decreased to-7000 Pa as the rapid decrease of the velocity of the sliding mass at t=10 s,which is seriously unfavorable for buildings and might be the key reason for the destructive collapse of buildings in the airblast zone of the Wangjiayan landslide.展开更多
This paper presents a 3D simulator used for studying the motion control and autonomous navigation of robotic fish. The simulator’s system structure and computation flow are presented. Simplified kinematics and hydrod...This paper presents a 3D simulator used for studying the motion control and autonomous navigation of robotic fish. The simulator’s system structure and computation flow are presented. Simplified kinematics and hydrodynamics models for a virtual robotic fish are proposed. Many other object models are created for water, obstacles, sonar sensors and a swimming pool. Experimental results show that the simulator provides a realistic and convenient way to develop autonomous navigation algorithms for robotic fish.展开更多
POM97, an oceanic model, has been used for the first time to the numerical study on the tidal waves of the as Regions around Taiwan. In this paper, we have got the result that the semidiurnal tidal waves of these area...POM97, an oceanic model, has been used for the first time to the numerical study on the tidal waves of the as Regions around Taiwan. In this paper, we have got the result that the semidiurnal tidal waves of these area mainly are the co-operating tides which come from the south of 23'N of the western Pacific. Those semidiurnal tidal waves affecting the Taiwan Straits come respectively from the south and the north entrance of the channel, and the north tidal wave is stronger than the south one. The strongest tidal field is the area from the Meizhou Bay to the Xinhua Bay along the coast of Fujian Province, where the biggest amplitude of the M2 partial tide can reach 240 cm. The strongest tidal cur- rent fields lie in the Penghu watercourse, where the maximum velocity of the M2 partial tide can arrive at 196 m/s. In the horizontal structure of the tidal currets, we have found that there is a stream dot in the north of the channel, besides, there still exist four new ones. As for the vertical structure, it mainly is biassed to the right at the surface, and to the left near the bottom layer.展开更多
A flexible flat torque converter was proposed to fulfill the requirement of miniaturization and power density maximization for automobiles.Constructed by two arcs joined by lines,the torus was designed directly from d...A flexible flat torque converter was proposed to fulfill the requirement of miniaturization and power density maximization for automobiles.Constructed by two arcs joined by lines,the torus was designed directly from design path.The influence of flatness on the performance of the torque converter was evaluated.The software CFX and standard k-ε model were adopted to simulate the internal flow fields of the torque converter under different flatness ratios.The results indicated that the performance of the torque converter got worse as the flatness declined,but the capacity of pump increased.The efficiency and the torque ratio dropped slightly as the flatness ratio decreased.So the torque converter could be squashed appropriately to get high power density without too much efficiency sacrifice.But when the flatness ratio was below 0.2,there was a significant drop in the efficiency.展开更多
Forward modeling is the basis of inversion imaging and quantitative interpretation for DC resistivity exploration.Currently,a numerical model of the DC resistivity method must be finely divided to obtain a highly accu...Forward modeling is the basis of inversion imaging and quantitative interpretation for DC resistivity exploration.Currently,a numerical model of the DC resistivity method must be finely divided to obtain a highly accurate solution under complex conditions,resulting in a long calculation time and large storage.Therefore,we propose a 3D numerical simulation method in a mixed space-wavenumber domain to overcome this challenge.The partial differential equation about abnormal potential is transformed into many independent ordinary differential equations with different wavenumbers using a 2D Fourier transform along the x axis and y axis direction.In this way,a large-scale 3D numerical simulation problem is decomposed into several 1D numerical simulation problems,which significantly reduces the computational and storage requirements.In addition,these ordinary 1D differential equations with different wavenumbers are independent of each other and high parallelelism of the algorithm.They are solved using a finite-element algorithm combined with a chasing method,and the obtained solution is modified using a contraction operator.In this method,the vertical direction is reserved as the spatial domain,then grid size can be determined flexibly based on the underground current density distribution,which considers the solution accuracy and calculation efficiency.In addition,for the first time,we use the contraction operator in the integral equation method to iterate the algorithm.The algorithm takes advantage of the high efficiency of the standard Fourier transform and chasing method,as well as the fast convergence of the contraction operator.We verified the accuracy of the algorithm and the convergence of the contraction operator.Compared with a volume integral method and goal-oriented adaptive finite-element method,the proposed algorithm has lower memory requirements and high computational efficiency,making it suitable for calculating a model with large-scale nodes.Moreover,different examples are used to verify the high adaptability and parallelism of the proposed algorithm.The findings show that the 3D numerical simulation method of DC resistivity method in a mixed space-wavenumber domain is highly efficient,precise,and parallel.展开更多
Vertical axis tidal current turbine is a promising device to extract energy from ocean current. One of the important components of the turbine is the connecting arm, which can bring about a significant effect on the p...Vertical axis tidal current turbine is a promising device to extract energy from ocean current. One of the important components of the turbine is the connecting arm, which can bring about a significant effect on the pressure distribution along the span of the turbine blade, herein we call it 3D effect. However, so far the effect is rarely reported in the research, moreover, in numerical simulation. In the present study, a 3D numerical model of the turbine with the connecting arm was developed by using FLUENT software compiling the UDF(User Defined Function) command. The simulation results show that the pressure distribution along the span of blade with the connecting arm model is significantly different from those without the connecting arm. To facilitate the validation of numerical model, the laboratory experiment has been carried out by using three different types of NACA aerofoil connecting arm and circle section connecting arm. And results show that the turbine with NACA0012 connecting arm has the best start-up performance which is 0.346 m/s and the peak point of power conversion coefficient is around 0.33. A further study has been performed and a conclusion is drawn that the aerofoil and thickness of connecting arm are the most important factors on the power conversion coefficient of the vertical axis tidal current turbine.展开更多
We employ the parallel computing technology to study numerically the three-dimensional structure of quantized vortices of Bose-Einstein condensates, For anisotropic cases, the bending process of vortices is described ...We employ the parallel computing technology to study numerically the three-dimensional structure of quantized vortices of Bose-Einstein condensates, For anisotropic cases, the bending process of vortices is described in detail by the decrease of Gross-Pitaevskii energy. A completely straight vortex and the steady and symmetrical multiple-vortex configurations are obtained. We analyse the effect of initial conditions and angular velocity on the number and shape of vortices.展开更多
Needle biopsy is an essential part of modern clinical medicine.The puncture accuracy and sampling success rate of puncture surgery can be effectively improved through virtual surgery.There are few three-dimensional pu...Needle biopsy is an essential part of modern clinical medicine.The puncture accuracy and sampling success rate of puncture surgery can be effectively improved through virtual surgery.There are few three-dimensional puncture(3D)models,which have little significance for surgical guidance under complicated conditions and restrict the development of virtual surgery.In this paper,a 3D simulation of the muscle tissue puncture process is studied.Firstly,the mechanical properties of muscle tissue are measured.The Mooney-Rivlin(M-R)model is selected by considering the fitting accuracy and calculation speed.Subsequently,an accurate 3D dynamic puncture model is established.The failure criterion is used to define the breaking characteristics of the muscle,and the bilinear cohesion model defines the breaking process.Experiments with different puncture speeds are carried out through the built in vitro puncture platform.The experimental results are compared with the simulation results.The experimental and simulated reaction force curves are highly consistent,which verifies the accuracy of the model.Finally,the model under different parameters is studied.The simulation results of varying puncture depths and puncture speeds are analyzed.The 3D puncture model can provide more accurate model support for virtual surgery and help improve the success rate of puncture surgery.展开更多
基金National Natural Science Foundation of China Under Grant No. 50408003National Scientifi c and Technical Supporting Programs Funded by Ministry of Science & Technology of China Under Grant No. 2006BAC13B01
文摘In this paper, near-fault strong ground motions caused by a surface rupture fault (SRF) and a buried fault (BF) are numerically simulated and compared by using a time-space-decoupled, explicit finite element method combined with a multi-transmitting formula (MTF) of an artificial boundary. Prior to the comparison, verification of the explicit element method and the MTF is conducted. The comparison results show that the final dislocation of the SRF is larger than the BF for the same stress drop on the fault plane. The maximum final dislocation occurs on the fault upper line for the SRF; however, for the BE the maximum final dislocation is located on the fault central part. Meanwhile, the PGA, PGV and PGD of long period ground motions (≤ 1 Hz) generated by the SRF are much higher than those of the BF in the near-fault region. The peak value of the velocity pulse generated by the SRF is also higher than the BE Furthermore, it is found that in a very narrow region along the fault trace, ground motions caused by the SRF are much higher than by the BF. These results may explain why SRFs almost always cause heavy damage in near-fault regions compared to buried faults.
文摘Objective To investigate the effect of computer aided 3D simulation technique for treating complicated foot and ankle fractures precisely.Methods From November 2007 to August 2009,255 patients with complicated foot and ankle fractures
基金supported by the National Natural Science Foundation of China(Grant Nos.41807277,42172306,and U1965204)the Natural Science Foundation of Hebei Province(Grant No.D2019202440)。
文摘The numerical simulation of internal features,such as inclusions and voids,is important to analyze their impact on the performance of composite materials.However,the complex geometries of internal features and the induced continuous-discontinuous(C-D)deformation fields are challenges to their numerical simulation.In this study,a 3D approach using a simple mesh to simulate irregular internal geometries is developed for the first time.With the help of a developed voxel crack model,image models that are efficient when recording complex geometries are directly imported into the simulation.Surface reconstructions,which are usually labor-intensive,are excluded from this approach.Moreover,using image models as the geometric input,image processing techniques are applied to detect material interfaces and develop contact pairs.Then,the C-D deformations of the complex internal features are directly calculated based on the numerical manifold method.The accuracy and convergence of the developed3D approach are examined based on multiple benchmarks.Successful 3D C-D simulation of sandstones with naturally formed complex microfeatures demonstrates the capability of the developed approach.
基金supported by the National Natural Science Foundation of China(Grant No.32271983,No.61571400).
文摘With the development of aviation agricultural technology,the number of farmers adopting the use of drones in daily agricultural activities is growing rapidly in recent decades.Among these,a large portion constitutes agricultural drones being used in pest control and crop protection practices,e.g.agriculture spraying of pesticides.Spraying pesticides with drones have proven to be faster than other traditional methods.On the downside,flight time and range of Unmanned Aerial Vehicles(UAV)are often limited.Thus,a proper arrangement of flight height and velocity will greatly improve spraying efficiency.A new strategy to optimize the flight parameters,i.e.flight height and flight velocity,for fixed-wing UAV with a 3D simulation-based approach together with an automatic optimization algorithm was proposed in this study.To find the optimal parameters for a UAV to fly and spray under certain environmental conditions,a three-dimensional model of the target crop was established first,followed by a detailed simulation of droplet spraying.As a demonstration case,a grass model was developed and used as the target plant,and a physics-based method was used to simulate realistically the movement of the droplets in the air as well as the interaction between the droplets and the plant to obtain the droplet deposition rate under the specified operating parameters.Furthermore,the standard Particle Swarm Optimization(PSO)algorithm was used to optimize the UAV operating parameters to obtain the best operating parameters.The results indicate that using the standard PSO algorithm to optimize the operating parameters of the drone could significantly improve the deposition rate and find the best operating parameters.
基金The Specialized Research Fund for the Doctoral Programof Higher Education(No.20010610023) and the Sino-Finnish Scientific and TechnologicalCooperation Program
文摘The standard three dimensional(3D) k-ε turbulence model was applied to simulate the flow field of a small scale combined oxidation ditch. The moving mesh approach was used to model the rotor of the ditch. Comparison of the computed and the measured data is acceptable. A vertical reverse flow zone in the ditch was found, and it played a very important role in the ditch flow behavior. The flow pattern in the ditch is discussed in detail, and approaches are suggested to improve the hydrodynamic performance in the ditch.
基金Natural Science Foundation of Shandong Province(Grant No.ZR2019JQ19)Interdisciplinary Research Project of Shandong University(Grant No.2017JC027)China Scholarship Council(CSC).
文摘Minimally invasive surgery is an important technique used for cytopathological examination.Recently,multiple studies have been conducted on a three-dimensional(3D)puncture simulation model as it can reveal the internal deformation state of the tissue at the micro level.In this study,a viscoelastic constitutive equation suitable for muscle tissue was derived.Additionally,a method was developed to define the fracture characteristics of muscle tissue material during the simulation process.The fracture of the muscle tissue in contact with the puncture needle was simulated using the cohesive zone model and a 3D puncture finite element model was established to analyze the deformation of the muscle tissue.The stress nephogram and reaction force under different parameters were compared and analyzed to study the deformation of the biological soft tissue and guide the actual operation process and reduce pain.
文摘This paper presents a new approach to parallelize 3D lattice Monte Carlo algorithms used in the numerical simulation of polymer on ZiQiang 2000 a cluster of symmetric multiprocessors (SMPs). The combined load for cell and energy calculations over the time step is balanced together to form a single spatial decomposition. Basic aspects and strategies of running Monte Carlo calculations on parallel computers are studied. Different steps involved in porting the software on a parallel architecture based on ZiQiang 2000 running under Linux and MPI are described briefly. It is found that parallelization becomes more advantageous when either the lattice is very large or the model contains many cells and chains.
基金Natural Science Foundation of Tianjin,China( No. 11JCYBJC26400) Tianjin High School Scientific and Technology Fund Planning Project,China( No. 20100310)
文摘Weft knitted fancy fabrics are widely used in knitted garment design. Due to the complexity of the structures, their modeling and simulation needs to be solved in three-dimensional (3D) CAD developments. In this paper, 3D loop geometrical models of weft knitted fancy structures, including tuck stitch, jacquard stitch, transfer stitch and fleecy stitch, were developed based on an improved model of plain loop, and their central axes as some 3D space curves were achieved by using Non-Uniform Rational B-Splines (NURBS). The 3D visual simulation programme was written in C++ programming language using OpenGL, which was a function library of 3D graphics. Some examples of weft knitted fancy fabrics were generated and practical application of 3D simulation was discussed.
文摘When heavy machines and large scaled receiver system of communication equipment are manufactured, it always needs to produce large-sized steel castings, aluminum castings and etc. Some defects of hot cracking by thermal stress often appear during solidification process as these castings are produced, which results in failure of castings. Therefore predicting the effects of technological parameters for production of castings on the thermal stress during solidification process becomes an important means. In this paper, the mathematical models have been established and numerical calculation of temperature fields by using finite difference method (FDM) and then thermal stress fields by using finite element method (FEM) during solidification process of castings have been carried out. The technological parameters of production have been optimized by the results of calculation and the defects of hot cracking have been eliminated. Modeling and simulation of 3D thermal stress during solidification processes of large-sized castings provided a scientific basis, which promoted further development of advanced manufacturing technique.
文摘Mountainous regions have disadvantages in economic development because of harsh physical and climatic conditions.However,winter tourism activities are one of the key components for supporting economic development in the highlands.Establishing a ski resort area supports direct and indirect employment in a region,and it stops immigration from mountainous regions to other places.This research aimed to assess the potential ski areas using a multi criteria evaluation technique in the Van region which is located in the eastern part of Türkiye.In this context,snow cover duration,sun effect,slope,slope length,elevation,population density,distance from main roads and lake visibility were used as input factors in the decision making process.Each factor was standardized using a fuzzy technique based on existing well-known ski centers in Türkiye.The weight of inputs was defined by applying a survey to the professional skiers.The most important factors were detected as transportation opportunities and snow covers whereas,the least important factors were elevation and population density.Additionally,lake visibility was very important to make a difference from other existing facilities in the region.Therefore,it was included as constraints and lake visible areas were extracted at the final stage of the research.Potential ski areas were mapped in three levels as professional,intermediate and beginner skiers.One of the suitable areas was selected as a sample projection and for the 3D simulation of the ski investment area.Potential costs and benefits were discussed.It was found that a ski tourism area investment can be amortized in 3 years in the region.
基金supported by the National Natural Science Foundation of China(Grant Nos.61274106,11175138,and 61601352)
文摘The fabrication process dependent effects on single event effects (SEEs) are investigated in a commercial silicon- germanium heterojunction bipolar transistor (SiGe HBT) using three-dimensional (3D) TCAD simulations. The influences of device structure and doping concentration on SEEs are discussed via analysis of current transient and charge collection induced by ions strike. The results show that the SEEs representation of current transient is different from representation of the charge collection for the same process parameters. To be specific, the area of C/S junction is the key parameter that affects charge collection of SEE. Both current transient and charge collection are dependent on the doping of collector and substrate. The base doping slightly influences transient currents of base, emitter, and collector terminals. However, the SEEs of SiGe HBT are hardly affected by the doping of epitaxial base and the content of Ge.
基金supported by the National Natural Science Foundation of China(42322702,42177131)。
文摘Airblasts,as one common phenomenon accompanied by rapid movements of landslides or rock/snow avalanches,commonly result in catastrophic damages and are attracting more and more scientific attention.To quantitatively analyze the intensity of airblast initiated by landslides,the Wangjiayan landslide,occurred in the Wenchuan earthquake,is selected here with the landslide propagation and airblast evolution being studied using FLUENT by introducing the Voellmy rheological law.The results reveal that:(1)For the Wangjiayan landslide,its whole travelling duration is only 12 s with its maximum velocity reaching 36 m/s at t=10 s;(2)corresponding to the landslide propagation,the maximum velocity,28 m/s,of the airblast initiated by the landslide also appears at t=10 s with its maximum pressure reaching594.8 Pa,which is equivalent to violent storm;(3)under the attack of airblast,the load suffered by buildings in the airblast zone increases to 1300 Pa at t=9.4 s and sharply decreased to-7000 Pa as the rapid decrease of the velocity of the sliding mass at t=10 s,which is seriously unfavorable for buildings and might be the key reason for the destructive collapse of buildings in the airblast zone of the Wangjiayan landslide.
文摘This paper presents a 3D simulator used for studying the motion control and autonomous navigation of robotic fish. The simulator’s system structure and computation flow are presented. Simplified kinematics and hydrodynamics models for a virtual robotic fish are proposed. Many other object models are created for water, obstacles, sonar sensors and a swimming pool. Experimental results show that the simulator provides a realistic and convenient way to develop autonomous navigation algorithms for robotic fish.
文摘POM97, an oceanic model, has been used for the first time to the numerical study on the tidal waves of the as Regions around Taiwan. In this paper, we have got the result that the semidiurnal tidal waves of these area mainly are the co-operating tides which come from the south of 23'N of the western Pacific. Those semidiurnal tidal waves affecting the Taiwan Straits come respectively from the south and the north entrance of the channel, and the north tidal wave is stronger than the south one. The strongest tidal field is the area from the Meizhou Bay to the Xinhua Bay along the coast of Fujian Province, where the biggest amplitude of the M2 partial tide can reach 240 cm. The strongest tidal cur- rent fields lie in the Penghu watercourse, where the maximum velocity of the M2 partial tide can arrive at 196 m/s. In the horizontal structure of the tidal currets, we have found that there is a stream dot in the north of the channel, besides, there still exist four new ones. As for the vertical structure, it mainly is biassed to the right at the surface, and to the left near the bottom layer.
基金Supported by the National Natural Science Foundation of China (50905016)
文摘A flexible flat torque converter was proposed to fulfill the requirement of miniaturization and power density maximization for automobiles.Constructed by two arcs joined by lines,the torus was designed directly from design path.The influence of flatness on the performance of the torque converter was evaluated.The software CFX and standard k-ε model were adopted to simulate the internal flow fields of the torque converter under different flatness ratios.The results indicated that the performance of the torque converter got worse as the flatness declined,but the capacity of pump increased.The efficiency and the torque ratio dropped slightly as the flatness ratio decreased.So the torque converter could be squashed appropriately to get high power density without too much efficiency sacrifice.But when the flatness ratio was below 0.2,there was a significant drop in the efficiency.
文摘Forward modeling is the basis of inversion imaging and quantitative interpretation for DC resistivity exploration.Currently,a numerical model of the DC resistivity method must be finely divided to obtain a highly accurate solution under complex conditions,resulting in a long calculation time and large storage.Therefore,we propose a 3D numerical simulation method in a mixed space-wavenumber domain to overcome this challenge.The partial differential equation about abnormal potential is transformed into many independent ordinary differential equations with different wavenumbers using a 2D Fourier transform along the x axis and y axis direction.In this way,a large-scale 3D numerical simulation problem is decomposed into several 1D numerical simulation problems,which significantly reduces the computational and storage requirements.In addition,these ordinary 1D differential equations with different wavenumbers are independent of each other and high parallelelism of the algorithm.They are solved using a finite-element algorithm combined with a chasing method,and the obtained solution is modified using a contraction operator.In this method,the vertical direction is reserved as the spatial domain,then grid size can be determined flexibly based on the underground current density distribution,which considers the solution accuracy and calculation efficiency.In addition,for the first time,we use the contraction operator in the integral equation method to iterate the algorithm.The algorithm takes advantage of the high efficiency of the standard Fourier transform and chasing method,as well as the fast convergence of the contraction operator.We verified the accuracy of the algorithm and the convergence of the contraction operator.Compared with a volume integral method and goal-oriented adaptive finite-element method,the proposed algorithm has lower memory requirements and high computational efficiency,making it suitable for calculating a model with large-scale nodes.Moreover,different examples are used to verify the high adaptability and parallelism of the proposed algorithm.The findings show that the 3D numerical simulation method of DC resistivity method in a mixed space-wavenumber domain is highly efficient,precise,and parallel.
基金financially supported by the State Oceanic Administration of China(Grant No.GHME2011CL01)the Program of State Key Laboratory of Coastal and Offshore Engineering(Grant No.LP1102)
文摘Vertical axis tidal current turbine is a promising device to extract energy from ocean current. One of the important components of the turbine is the connecting arm, which can bring about a significant effect on the pressure distribution along the span of the turbine blade, herein we call it 3D effect. However, so far the effect is rarely reported in the research, moreover, in numerical simulation. In the present study, a 3D numerical model of the turbine with the connecting arm was developed by using FLUENT software compiling the UDF(User Defined Function) command. The simulation results show that the pressure distribution along the span of blade with the connecting arm model is significantly different from those without the connecting arm. To facilitate the validation of numerical model, the laboratory experiment has been carried out by using three different types of NACA aerofoil connecting arm and circle section connecting arm. And results show that the turbine with NACA0012 connecting arm has the best start-up performance which is 0.346 m/s and the peak point of power conversion coefficient is around 0.33. A further study has been performed and a conclusion is drawn that the aerofoil and thickness of connecting arm are the most important factors on the power conversion coefficient of the vertical axis tidal current turbine.
基金Project supported partly by the National Natural Science Foundation of China (Grant Nos 10301034 and 40574069), The authors thank Professor Du Q very much for his important discussions.
文摘We employ the parallel computing technology to study numerically the three-dimensional structure of quantized vortices of Bose-Einstein condensates, For anisotropic cases, the bending process of vortices is described in detail by the decrease of Gross-Pitaevskii energy. A completely straight vortex and the steady and symmetrical multiple-vortex configurations are obtained. We analyse the effect of initial conditions and angular velocity on the number and shape of vortices.
基金the Natural Science Foundation of Shandong Province(Grant No.ZR2019JQ19)the interdisciplinary research project of Shandong University(Grant No.2017JC027).
文摘Needle biopsy is an essential part of modern clinical medicine.The puncture accuracy and sampling success rate of puncture surgery can be effectively improved through virtual surgery.There are few three-dimensional puncture(3D)models,which have little significance for surgical guidance under complicated conditions and restrict the development of virtual surgery.In this paper,a 3D simulation of the muscle tissue puncture process is studied.Firstly,the mechanical properties of muscle tissue are measured.The Mooney-Rivlin(M-R)model is selected by considering the fitting accuracy and calculation speed.Subsequently,an accurate 3D dynamic puncture model is established.The failure criterion is used to define the breaking characteristics of the muscle,and the bilinear cohesion model defines the breaking process.Experiments with different puncture speeds are carried out through the built in vitro puncture platform.The experimental results are compared with the simulation results.The experimental and simulated reaction force curves are highly consistent,which verifies the accuracy of the model.Finally,the model under different parameters is studied.The simulation results of varying puncture depths and puncture speeds are analyzed.The 3D puncture model can provide more accurate model support for virtual surgery and help improve the success rate of puncture surgery.