The dynamic fracture behaviors of Ti-6Al-4V alloy at high strain rate loading were investigated systemically through Taylor impact test, over the range of impact velocities from 145 m/s to 306 m/s. The critical impact...The dynamic fracture behaviors of Ti-6Al-4V alloy at high strain rate loading were investigated systemically through Taylor impact test, over the range of impact velocities from 145 m/s to 306 m/s. The critical impact velocity of fracture ranges from 217 m/s to 236 m/s. Smooth surfaces and ductile dimple areas were observed on the fracture surfaces. As the impact velocity reached 260 m/s, the serious melting regions were also observed on the fracture surfaces. Self-organization of cracks emerges when the impact velocity reaches 260 m/s, while some special cracks whose "tips" are not sharp but arc and smooth, and without any evidence of deformation or adiabatic shear band were also observed on the impact end surfaces. Examination of the sections of these special cracks reveals that the cracks expand along the two maximum shear stress directions respectively, and finally intersect as a tridimensional "stagger ridge" structure.展开更多
目的探讨(1-3)-β-D葡聚糖联合降钙素原(procalcitonin,PCT)、CD4^(+)T淋巴细胞多指标在艾滋病患者马尔尼菲篮状菌感染早期诊断临床研究。方法回顾性选取我院2020年1月—2022年6月住院的120例艾滋病患者为研究对象。依据实验室结果,将...目的探讨(1-3)-β-D葡聚糖联合降钙素原(procalcitonin,PCT)、CD4^(+)T淋巴细胞多指标在艾滋病患者马尔尼菲篮状菌感染早期诊断临床研究。方法回顾性选取我院2020年1月—2022年6月住院的120例艾滋病患者为研究对象。依据实验室结果,将其分为马尔尼菲篮状菌感染确诊组(血或组织液培育养出马尔尼菲篮状菌),简称A组(62例),及马尔尼菲篮状菌感染临床诊断组[根据临床症状、体征、血常规及(1-3)-β-D葡聚糖、PCT、CD4^(+)T淋巴细胞多指标诊断],简称B组(58例)。检测患者(1-3)-β-D葡聚糖、PCT、CD4^(+)T淋巴细胞的表达水平,采用受试者工作特征(receiver-operating characteristic,ROC)曲线下面积(area under the curve,AUC)评估上述指标联合检测对艾滋病患者感染马尔尼菲篮状菌的诊断效能。结果A组的(1-3)-β-D葡聚糖和PCT水平均高于B组,CD4^(+)T淋巴细胞个数低于B组(P<0.05);(1-3)-β-D葡聚糖、PCT、CD4^(+)T淋巴细胞联合检测的AUC为0.933,(1-3)-β-D葡聚糖单独检测的AUC是0.812,PCT单独检测的AUC为0.883,CD4^(+)T淋巴细胞单独检测的AUC是0.810,(1-3)-β-D葡聚糖、PCT和CD4^(+)T淋巴细胞联合检测的AUC皆优于三项单独检测,表明(1-3)-β-D葡聚糖、PCT和CD4^(+)T淋巴细胞联合检测的诊断价值皆优于单一指标诊断,且联合检测的特异度、约登指数分别为92.43%和0.580,均高于三项单独检测。结论(1-3)-β-D葡聚糖联合PCT和CD4^(+)T淋巴细胞多指标对艾滋病马尔尼菲篮状菌感染具有非常高的临床诊断价值,能够帮助医生分析出高危风险患者,及时制定治疗方案,同时也承担预后效果的判断依据,对治疗艾滋病马尔尼菲篮状菌感染具有非常重要的研究价值。展开更多
The quasi-static and dynamic tensile behaviors in electron beam welded(EBW) Ti-6Al-4V alloy were investigated at strain rates of 10-3 and 103 s-1,respectively,by materials test system(MTS) and reconstructive Hopki...The quasi-static and dynamic tensile behaviors in electron beam welded(EBW) Ti-6Al-4V alloy were investigated at strain rates of 10-3 and 103 s-1,respectively,by materials test system(MTS) and reconstructive Hopkinson bars apparatus.The microstructures of the base metal(BM) and the welded metal(WM) were observed with optical microscope.The fracture characteristics of the BM and WM were characterized with scanning electronic microscope.In Ti-6Al-4V alloy joint,the flow stress of WM is higher than that of BM,while the fracture strain of WM is less than that of BM at strain rates of 103 and 10-3 s-1,respectively.The fracture strain of WM has apparent improvement when the strain rate rises from 10-3 to 103 s-1,while the fracture strain of BM almost has no change.At the same time,the fracture mode of WM alters from brittle to ductile fracture,which causes improvement of the fracture strain of WM.展开更多
Molecular dynamic simulation was employed to predict the melting points Tm of TNAD/HMX, TNAD/RDX, TNAD/DINA, and TNAD/DNP systems (tans-1,4,5,8- tetranitro-1,4,5,8-tetraazadacalin (TNAD), dinitropiperazine (DNP),...Molecular dynamic simulation was employed to predict the melting points Tm of TNAD/HMX, TNAD/RDX, TNAD/DINA, and TNAD/DNP systems (tans-1,4,5,8- tetranitro-1,4,5,8-tetraazadacalin (TNAD), dinitropiperazine (DNP), cyclotetramethylenetetranitroamine (HMX), cyclotrimethylenetrinitramine (RDX), and N-nitrodihydroxyethylaminedinitrate (DINA)). Tm was determined from the inflexion point on the curve of mean specific volume vs. temperature. The result shows that the Tm values of TNAD/HMX, TNAD/RDX, and TNAD/DINA systems are 500, 536, and 488 K, respectively. The TNAD/DNP system has no obvious Tm value, which shows the system is insoluble. Using Tm, the solubility of the four systems was analyzed. The radial distribution functions of the four systems were analyzed and the main intermolecular forces between TNAD and other energetic components are short-range interactions. The better the solubility is, the stronger the intermoleenlar interaction is. In addition, the force field energy at different temperature was also analyzed to predict Tm of the four systems.展开更多
In order to have a better understanding of the hot deformation behavior of the as-solution-treated Mg-4 Zn-2 Sn-2 Al(ZAT422) alloy, a series of compression experiments with a height reduction of 60% were performed i...In order to have a better understanding of the hot deformation behavior of the as-solution-treated Mg-4 Zn-2 Sn-2 Al(ZAT422) alloy, a series of compression experiments with a height reduction of 60% were performed in the temperature range of 498-648 K and the strain rate range of 0.01-5 s~(-1) on a Gleeble 3800 thermo-mechanical simulator. Based on the regression analysis by Arrhenius type equation and Avrami type equation of flow behavior, the activation energy of deformation of ZAT422 alloy was determined as 155.652 k J/mol, and the constitutive equations for flow behavior and the dynamic recrystallization(DRX) kinetic model of ZAT422 alloy were established. Microstructure observation shows that when the temperature is as low as 498 K, the DRX is not completed as the true strain reaches 0.9163. However, with the temperature increasing to 648 K, the lower strain rate is more likely to result in some grains' abnormal growth.展开更多
To study the prediction of the anomalous precipitation and general circulation for the summer(June–July–August) of1998, the Community Climate System Model Version 4.0(CCSM4.0) integrations were used to drive ver...To study the prediction of the anomalous precipitation and general circulation for the summer(June–July–August) of1998, the Community Climate System Model Version 4.0(CCSM4.0) integrations were used to drive version 3.2 of the Weather Research and Forecasting(WRF3.2) regional climate model to produce hindcasts at 60 km resolution. The results showed that the WRF model produced improved summer precipitation simulations. The systematic errors in the east of the Tibetan Plateau were removed, while in North China and Northeast China the systematic errors still existed. The improvements in summer precipitation interannual increment prediction also had regional characteristics. There was a marked improvement over the south of the Yangtze River basin and South China, but no obvious improvement over North China and Northeast China. Further analysis showed that the improvement was present not only for the seasonal mean precipitation, but also on a sub-seasonal timescale. The two occurrences of the Mei-yu rainfall agreed better with the observations in the WRF model,but were not resolved in CCSM. These improvements resulted from both the higher resolution and better topography of the WRF model.展开更多
Combined multi-body dynamics with structural dynamics, a new discrete element with flexible connector, which is applicable for 3-D beam structures, is developed in this paper. Both the generalized elastic coefficient ...Combined multi-body dynamics with structural dynamics, a new discrete element with flexible connector, which is applicable for 3-D beam structures, is developed in this paper. Both the generalized elastic coefficient matrix of the flexible connector and the mass matrix of discrete element may be off-diagonal in a general case. The zero-length rigid element is introduced to simulate the node at which multiple elements are jointed together. It may also be effective when the axes of adjacent elements are not in the same line. The examples for eigenvalue calculation show that the model is successful. It can be extended to the geometric nonlinear response analysis.展开更多
Binary Al-4Mg alloy have been deformed by hot torsion at 300-500 deg C andstrain rates of 0.006-1.587 s^(-1) to a true strain of 5.5. The specimens were annealed in vacuumfor 1.5 h at 500 deg C and then water quenched...Binary Al-4Mg alloy have been deformed by hot torsion at 300-500 deg C andstrain rates of 0.006-1.587 s^(-1) to a true strain of 5.5. The specimens were annealed in vacuumfor 1.5 h at 500 deg C and then water quenched. The study indicates that the dynamicrecrystallization occurs during hot torsion of Al-4Mg alloy in a certain range of Z parameter(Zener-Hollmon Parameter), i.e. 19.3 <= lnZ <=24.8. Increasing the strain rate at higher deformationtemperature or reducing the strain rate at lower deformation temperature accelerates the occurrenceof dynamic recrystallization in the alloy.展开更多
Accurate 3-D fracture network model for rock mass in dam foundation is of vital importance for stability,grouting and seepage analysis of dam foundation.With the aim of reducing deviation between fracture network mode...Accurate 3-D fracture network model for rock mass in dam foundation is of vital importance for stability,grouting and seepage analysis of dam foundation.With the aim of reducing deviation between fracture network model and measured data,a 3-D fracture network dynamic modeling method based on error analysis was proposed.Firstly,errors of four fracture volume density estimation methods(proposed by ODA,KULATILAKE,MAULDON,and SONG)and that of four fracture size estimation methods(proposed by EINSTEIN,SONG and TONON)were respectively compared,and the optimal methods were determined.Additionally,error index representing the deviation between fracture network model and measured data was established with integrated use of fractal dimension and relative absolute error(RAE).On this basis,the downhill simplex method was used to build the dynamic modeling method,which takes the minimum of error index as objective function and dynamically adjusts the fracture density and size parameters to correct the error index.Finally,the 3-D fracture network model could be obtained which meets the requirements.The proposed method was applied for 3-D fractures simulation in Miao Wei hydropower project in China for feasibility verification and the error index reduced from 2.618 to 0.337.展开更多
A mathematical model expressing the motion of a pair of multi-DOF robot fingers with hemi-spherical ends, grasping a 3-D rigid object with parallel fiat surfaces, is derived, together with non-holonomic constraints. B...A mathematical model expressing the motion of a pair of multi-DOF robot fingers with hemi-spherical ends, grasping a 3-D rigid object with parallel fiat surfaces, is derived, together with non-holonomic constraints. By referring to the fact that humans grasp an object in the form of precision prehension, dynamically and stably by opposable forces, between the thumb and another finger (index or middle finger), a simple control signal constructed from finger-thumb opposition is proposed, and shown to realize stable grasping in a dynamic sense without using object information or external sensing (this is called "blind grasp" in this paper). The stability of grasping with force/torque balance under non-holonomic constraints is analyzed on the basis of a new concept named "stability on a manifold". Preliminary simulation results are shown to verify the validity of the theoretical results.展开更多
The time-domain BEM was developed to analyze the dynamic stress intensity factor ( DSIF) of 3-D elastodynamic crack problems. To simulate the stress singularity along the front of a crack, eight-node isoparametric sin...The time-domain BEM was developed to analyze the dynamic stress intensity factor ( DSIF) of 3-D elastodynamic crack problems. To simulate the stress singularity along the front of a crack, eight-node isoparametric singular elements were used, and the DSIF for a semi-circular surface crack was firstly calculated based on displacement equation using the time-domain BEM formulation. The new scheme to determine the time step was brought forward. By the dynamic analysis program of time-domain BEM compiled by its, several numerical examples are presented, which demonstrate the unconditional stability and high accuracy of time-domain BEM applied to 3-D elastodynamic crack problems.展开更多
Previous studies showed that 4 D-Var technique used for data assimilation could be modified for weather control. This study demonstrates the ability of 4 D-Var to influence the future path of a tropical cyclone by cal...Previous studies showed that 4 D-Var technique used for data assimilation could be modified for weather control. This study demonstrates the ability of 4 D-Var to influence the future path of a tropical cyclone by calculating perturbations in WRF simulation. Given the background error covariance matrix, the initial field is improved by the vortex dynamic initialization technique. Our results show that 4 D-Var can be applied to control the trajectory of simulated tropical cyclones by producing "optimal" perturbations. In the numerical simulation experiment of Typhoon Mitag in 2019, after this kind of weather control similar to data assimilation, the tropical cyclone moved obviously,and the damaging wind over the coastline weakened. The prediction results after the initial field modified by 4 D-Var have a great change, and the position of the tropical cyclone moved about 0.5° southeastward after assimilation,which misses the southeast coast of China. Moreover, the damaging wind is also weakened. Since the 4 D-Var is premised on the assumption that the model is perfect and does not consider the model error, then the research plan to consider model error and introduce new methods is discussed in the paper.展开更多
Single crystal silicon carbide(SiC)is widely used for optoelectronics applications.Due to the anisotropic characteristics of single crystal materials,the C face and Si face of single crystal SiC have different physica...Single crystal silicon carbide(SiC)is widely used for optoelectronics applications.Due to the anisotropic characteristics of single crystal materials,the C face and Si face of single crystal SiC have different physical properties,which may fit for particular application purposes.This paper presents an investigation of the material removal and associated subsurface defects in a set of scratching tests on the C face and Si face of 4H-SiC and 6H-SiC materials using molecular dynamics simulations.The investigation reveals that the sample material deformation consists of plastic,amorphous transformations and dislocation slips that may be prone to brittle split.The results showed that the material removal at the C face is more effective with less amorphous deformation than that at the Si face.Such a phenomenon in scratching relates to the dislocations on the basal plane(0001)of the SiC crystal.Subsurface defects were reduced by applying scratching cut depths equal to integer multiples of a half molecular lattice thickness,which formed a foundation for selecting machining control parameters for the best surface quality.展开更多
To investigate the mechanisms of microwave induced pacemaker cell injuries, Wistar rats and the primary pacemaker cells of newborn Wistar rats were exposed to microwave at average power density of 50 mW/cm2. Slower sp...To investigate the mechanisms of microwave induced pacemaker cell injuries, Wistar rats and the primary pacemaker cells of newborn Wistar rats were exposed to microwave at average power density of 50 mW/cm2. Slower spontaneous beating rate, intercellular Ca2+ aggregation and cell membrane perforation were detected immediately after the exposure. Moreover, hyperpolarizationactivated cyclic nucleotide-gated cation channel 4 (HCN4) was down-regulated immediately after the exposure and up-regulated at 12 h after the exposure. In the sinoatrial node (SAN) of the rats,展开更多
A cellular automaton (CA) model is established to simulate dynamic recrystallization (DRX) in the β single-phase field of Ti6Al4 V alloy, and the kinetics during DRX processing has been analyzed. The model employ...A cellular automaton (CA) model is established to simulate dynamic recrystallization (DRX) in the β single-phase field of Ti6Al4 V alloy, and the kinetics during DRX processing has been analyzed. The model employed considers the influences of dynamic recovery, nucleation rate, strain rate and dislocation density on DRX, and practical deformation parameters, such as temperature, strain and strain rate on DRX have been considered in the simulation. The simulated DRX grain size and DRX grain shape agree well with the experimental results, which shows the availability and lea- sibility of the cellular automaton method for the simulation of DRX. The result of kinetics analysis of DRX reveals that the Avrami exponent is variable ranging from 2.4 to 2.9, which increases with the increase of strain rate.展开更多
The dynamic mechanical properties of the Ti-6Al-4V(TC4)alloy prepared by laser additive manufacturing(LAM-TC4)under the high strain rate(HSR)are proposed.The dynamic compression experiments of LAM-TC4 are conducted wi...The dynamic mechanical properties of the Ti-6Al-4V(TC4)alloy prepared by laser additive manufacturing(LAM-TC4)under the high strain rate(HSR)are proposed.The dynamic compression experiments of LAM-TC4 are conducted with the split Hopkinson pressure bar(SHPB)equipment.The results show that as the strain rate increases,the widths of the adiabatic shear band(ASB),the micro-hardness,the degree of grain refinement near the ASB,and the dislocation density of grains grow gradually.Moreover,the increase of dislocation density of grains is the root factor in enhancing the yield strength of LAM-TC4.Meanwhile,the heat produced from the distortion and dislocations of grains promotes the heat softening effect favorable for the recrystallization of grains,resulting in the grain refinement of ASB.Furthermore,the contrastive analysis between LAM-TC4 and TC4 prepared by forging(F-TC4)indicates that under the HSR,the yield strength of LAM-TC4 is higher than that of F-TC4.展开更多
The synthesis of new 4-imino-4H-chromeno[2,3-d]pyrimidin-3(5H)-amine in four steps including one step under microwave dielectric heating is reported. The structural identity of the synthesized compounds was establishe...The synthesis of new 4-imino-4H-chromeno[2,3-d]pyrimidin-3(5H)-amine in four steps including one step under microwave dielectric heating is reported. The structural identity of the synthesized compounds was established according to their spectroscopic analysis, such as FT-IR, NMR and mass spectroscopy. These new compounds were tested for their antiproliferative activities on seven representative human tumoral cell lines (Huh7 D12, Caco2, MDA-MB231, MDA-MB468, HCT116, PC3 and MCF7) and also on fibroblasts. Among them, only the compounds 6c showed micromolar cytotoxic activity on tumor cell lines (1.8 50 50 > 25 μM). Finally, in silico ADMET studies ware performed to investigate the possibility of using of the identified compound 6c as potential anti-tumor compound.展开更多
Hot deformation behaviors and microstructure evolution of Ti-3Al-5Mo-4Cr-2Zr-1Fe(Ti-35421)alloy in theβsingle field are investigated by isothermal compression tests on a Gleeble-3500 simulator at temperatures of 820-...Hot deformation behaviors and microstructure evolution of Ti-3Al-5Mo-4Cr-2Zr-1Fe(Ti-35421)alloy in theβsingle field are investigated by isothermal compression tests on a Gleeble-3500 simulator at temperatures of 820-900°C and strain rates of 0.001-1 s^(-1).The research results show that discontinuous yield phenomenon and rheological softening are affected by the strain rates and deformation temperatures.The critical conditions for dynamic recrystallization and kinetic model of Ti-35421 alloy are determined,and the Arrhenius constitutive model is constructed.The rheological behaviors of Ti-35421 alloys aboveβphase transformation temperature are predicted by the constitutive model accurately.The EBSD analysis proves that the deformation softening is controlled by dynamic recovery and dynamic recrystallization.In addition,continuous dynamic recrystallization is determined during hot deformation,and the calculation model for recrystallization grain sizes is established.Good linear dependency between the experimental and simulated values of recrystallized grain sizes indicates that the present model can be used for the prediction of recrystallized grain size with high accuracy.展开更多
The main research motive is to analysis and to veiny the inherent nonlinear character of MPEG-4 video. The power spectral density estimation of the video trafiic describes its 1/f^β and periodic characteristics.The p...The main research motive is to analysis and to veiny the inherent nonlinear character of MPEG-4 video. The power spectral density estimation of the video trafiic describes its 1/f^β and periodic characteristics.The priraeipal compohems analysis of the reconstructed space dimension shows only several principal components can be the representation of all dimensions. The correlation dimension analysis proves its fractal characteristic. To accurately compute the largest Lyapunov exponent, the video traffic is divided into many parts.So the largest Lyapunov exponent spectrum is separately calculated using the small data sets method. The largest Lyapunov exponent spectrum shows there exists abundant nonlinear chaos in MPEG-4 video traffic. The conclusion can be made that MPEG-4 video traffic have complex nonlinear be havior and can be characterized by its power spectral density,principal components, correlation dimension and the largest Lyapunov exponent besides its common statistics.展开更多
An improved three-dimensional (3-D) experimental visualization methodology is presented tor evaluating the fracture mechanisms of ferritic stainless steels by in-situ tensile testing with an environmental scanning e...An improved three-dimensional (3-D) experimental visualization methodology is presented tor evaluating the fracture mechanisms of ferritic stainless steels by in-situ tensile testing with an environmental scanning electron microscope (ESEM). The samples were machined with a radial notched shape and a sloped surface. Both planar surface deformation and sloping surface deformation-induced microvoids were observed during dynamic tension experiments, where a greater amount of information could be obtained from the sloping surface. The results showed that microvoids formed at the grain boundaries of highly elongated large grains. The microvoids nucleated in the severely deformed regions grew nearly parallel to the tensile axis, predominantly along the grain boundaries. The microvoids nucleated at the interface of particles and the matrix did not propagate due to the high plasticity of the matrix. The large microvoids propagated and showed a zigzag shape along the grain boundaries,seemingly a consequence of the fracture of the slip bands caused by dislocation pile-ups. The final failure took place due to the reduction of the load-beating area.展开更多
基金Project (51001014) supported by the Young Scientists Fund of the National Natural Science Foundation of China
文摘The dynamic fracture behaviors of Ti-6Al-4V alloy at high strain rate loading were investigated systemically through Taylor impact test, over the range of impact velocities from 145 m/s to 306 m/s. The critical impact velocity of fracture ranges from 217 m/s to 236 m/s. Smooth surfaces and ductile dimple areas were observed on the fracture surfaces. As the impact velocity reached 260 m/s, the serious melting regions were also observed on the fracture surfaces. Self-organization of cracks emerges when the impact velocity reaches 260 m/s, while some special cracks whose "tips" are not sharp but arc and smooth, and without any evidence of deformation or adiabatic shear band were also observed on the impact end surfaces. Examination of the sections of these special cracks reveals that the cracks expand along the two maximum shear stress directions respectively, and finally intersect as a tridimensional "stagger ridge" structure.
文摘目的探讨(1-3)-β-D葡聚糖联合降钙素原(procalcitonin,PCT)、CD4^(+)T淋巴细胞多指标在艾滋病患者马尔尼菲篮状菌感染早期诊断临床研究。方法回顾性选取我院2020年1月—2022年6月住院的120例艾滋病患者为研究对象。依据实验室结果,将其分为马尔尼菲篮状菌感染确诊组(血或组织液培育养出马尔尼菲篮状菌),简称A组(62例),及马尔尼菲篮状菌感染临床诊断组[根据临床症状、体征、血常规及(1-3)-β-D葡聚糖、PCT、CD4^(+)T淋巴细胞多指标诊断],简称B组(58例)。检测患者(1-3)-β-D葡聚糖、PCT、CD4^(+)T淋巴细胞的表达水平,采用受试者工作特征(receiver-operating characteristic,ROC)曲线下面积(area under the curve,AUC)评估上述指标联合检测对艾滋病患者感染马尔尼菲篮状菌的诊断效能。结果A组的(1-3)-β-D葡聚糖和PCT水平均高于B组,CD4^(+)T淋巴细胞个数低于B组(P<0.05);(1-3)-β-D葡聚糖、PCT、CD4^(+)T淋巴细胞联合检测的AUC为0.933,(1-3)-β-D葡聚糖单独检测的AUC是0.812,PCT单独检测的AUC为0.883,CD4^(+)T淋巴细胞单独检测的AUC是0.810,(1-3)-β-D葡聚糖、PCT和CD4^(+)T淋巴细胞联合检测的AUC皆优于三项单独检测,表明(1-3)-β-D葡聚糖、PCT和CD4^(+)T淋巴细胞联合检测的诊断价值皆优于单一指标诊断,且联合检测的特异度、约登指数分别为92.43%和0.580,均高于三项单独检测。结论(1-3)-β-D葡聚糖联合PCT和CD4^(+)T淋巴细胞多指标对艾滋病马尔尼菲篮状菌感染具有非常高的临床诊断价值,能够帮助医生分析出高危风险患者,及时制定治疗方案,同时也承担预后效果的判断依据,对治疗艾滋病马尔尼菲篮状菌感染具有非常重要的研究价值。
文摘The quasi-static and dynamic tensile behaviors in electron beam welded(EBW) Ti-6Al-4V alloy were investigated at strain rates of 10-3 and 103 s-1,respectively,by materials test system(MTS) and reconstructive Hopkinson bars apparatus.The microstructures of the base metal(BM) and the welded metal(WM) were observed with optical microscope.The fracture characteristics of the BM and WM were characterized with scanning electronic microscope.In Ti-6Al-4V alloy joint,the flow stress of WM is higher than that of BM,while the fracture strain of WM is less than that of BM at strain rates of 103 and 10-3 s-1,respectively.The fracture strain of WM has apparent improvement when the strain rate rises from 10-3 to 103 s-1,while the fracture strain of BM almost has no change.At the same time,the fracture mode of WM alters from brittle to ductile fracture,which causes improvement of the fracture strain of WM.
基金V. ACKNOWLEDGMENTS This work was supported by the National Natural Science Foundation of China (No.U1304111), the Laboratory of Science and Technology on Combustion and Explosion (No.9140C3501021101), China Postdoctoral Science Foundation (No.2013M531361), and Jiangsu Planned Projects for Postdoctoral Research Funds (No.1201015B).
文摘Molecular dynamic simulation was employed to predict the melting points Tm of TNAD/HMX, TNAD/RDX, TNAD/DINA, and TNAD/DNP systems (tans-1,4,5,8- tetranitro-1,4,5,8-tetraazadacalin (TNAD), dinitropiperazine (DNP), cyclotetramethylenetetranitroamine (HMX), cyclotrimethylenetrinitramine (RDX), and N-nitrodihydroxyethylaminedinitrate (DINA)). Tm was determined from the inflexion point on the curve of mean specific volume vs. temperature. The result shows that the Tm values of TNAD/HMX, TNAD/RDX, and TNAD/DINA systems are 500, 536, and 488 K, respectively. The TNAD/DNP system has no obvious Tm value, which shows the system is insoluble. Using Tm, the solubility of the four systems was analyzed. The radial distribution functions of the four systems were analyzed and the main intermolecular forces between TNAD and other energetic components are short-range interactions. The better the solubility is, the stronger the intermoleenlar interaction is. In addition, the force field energy at different temperature was also analyzed to predict Tm of the four systems.
基金Project(2016YFB0301105)supported by the National Key Research and Development Plan,ChinaProject(ZR2015YL007)supported by the Natural Science Foundation of Shandong Province,ChinaProject(ZR2015EQ019)supported by the Natural Science Foundation of Shandong Province,China
文摘In order to have a better understanding of the hot deformation behavior of the as-solution-treated Mg-4 Zn-2 Sn-2 Al(ZAT422) alloy, a series of compression experiments with a height reduction of 60% were performed in the temperature range of 498-648 K and the strain rate range of 0.01-5 s~(-1) on a Gleeble 3800 thermo-mechanical simulator. Based on the regression analysis by Arrhenius type equation and Avrami type equation of flow behavior, the activation energy of deformation of ZAT422 alloy was determined as 155.652 k J/mol, and the constitutive equations for flow behavior and the dynamic recrystallization(DRX) kinetic model of ZAT422 alloy were established. Microstructure observation shows that when the temperature is as low as 498 K, the DRX is not completed as the true strain reaches 0.9163. However, with the temperature increasing to 648 K, the lower strain rate is more likely to result in some grains' abnormal growth.
基金supported by the National Natural Science Foundation of China (Grant No. 41130103)the special Fund for Public Welfare Industry (Meteorology) (Grant No. GYHY201306026)+1 种基金the National Natural Science Foundation for Distinguished Young Scientists of China (Grant No. 41325018)the National Basic Research Program of China (Grant No. 2010CB951901)
文摘To study the prediction of the anomalous precipitation and general circulation for the summer(June–July–August) of1998, the Community Climate System Model Version 4.0(CCSM4.0) integrations were used to drive version 3.2 of the Weather Research and Forecasting(WRF3.2) regional climate model to produce hindcasts at 60 km resolution. The results showed that the WRF model produced improved summer precipitation simulations. The systematic errors in the east of the Tibetan Plateau were removed, while in North China and Northeast China the systematic errors still existed. The improvements in summer precipitation interannual increment prediction also had regional characteristics. There was a marked improvement over the south of the Yangtze River basin and South China, but no obvious improvement over North China and Northeast China. Further analysis showed that the improvement was present not only for the seasonal mean precipitation, but also on a sub-seasonal timescale. The two occurrences of the Mei-yu rainfall agreed better with the observations in the WRF model,but were not resolved in CCSM. These improvements resulted from both the higher resolution and better topography of the WRF model.
基金The project was financially supported by the National Natural Science Foundation of China
文摘Combined multi-body dynamics with structural dynamics, a new discrete element with flexible connector, which is applicable for 3-D beam structures, is developed in this paper. Both the generalized elastic coefficient matrix of the flexible connector and the mass matrix of discrete element may be off-diagonal in a general case. The zero-length rigid element is introduced to simulate the node at which multiple elements are jointed together. It may also be effective when the axes of adjacent elements are not in the same line. The examples for eigenvalue calculation show that the model is successful. It can be extended to the geometric nonlinear response analysis.
基金The project was sponsored by the Education Administration Major Project for Science Research under the contract No. 99134.
文摘Binary Al-4Mg alloy have been deformed by hot torsion at 300-500 deg C andstrain rates of 0.006-1.587 s^(-1) to a true strain of 5.5. The specimens were annealed in vacuumfor 1.5 h at 500 deg C and then water quenched. The study indicates that the dynamicrecrystallization occurs during hot torsion of Al-4Mg alloy in a certain range of Z parameter(Zener-Hollmon Parameter), i.e. 19.3 <= lnZ <=24.8. Increasing the strain rate at higher deformationtemperature or reducing the strain rate at lower deformation temperature accelerates the occurrenceof dynamic recrystallization in the alloy.
基金Project(51321065)supported by the Innovative Research Groups of the National Natural Science Foundation of ChinaProject(2013CB035904)supported by the National Basic Research Program of China(973 Program)Project(51439005)supported by the National Natural Science Foundation of China
文摘Accurate 3-D fracture network model for rock mass in dam foundation is of vital importance for stability,grouting and seepage analysis of dam foundation.With the aim of reducing deviation between fracture network model and measured data,a 3-D fracture network dynamic modeling method based on error analysis was proposed.Firstly,errors of four fracture volume density estimation methods(proposed by ODA,KULATILAKE,MAULDON,and SONG)and that of four fracture size estimation methods(proposed by EINSTEIN,SONG and TONON)were respectively compared,and the optimal methods were determined.Additionally,error index representing the deviation between fracture network model and measured data was established with integrated use of fractal dimension and relative absolute error(RAE).On this basis,the downhill simplex method was used to build the dynamic modeling method,which takes the minimum of error index as objective function and dynamically adjusts the fracture density and size parameters to correct the error index.Finally,the 3-D fracture network model could be obtained which meets the requirements.The proposed method was applied for 3-D fractures simulation in Miao Wei hydropower project in China for feasibility verification and the error index reduced from 2.618 to 0.337.
基金This work was supported in part by the Grant-in-Aid for Exploratory Research of the JSPS (No. 16656085).
文摘A mathematical model expressing the motion of a pair of multi-DOF robot fingers with hemi-spherical ends, grasping a 3-D rigid object with parallel fiat surfaces, is derived, together with non-holonomic constraints. By referring to the fact that humans grasp an object in the form of precision prehension, dynamically and stably by opposable forces, between the thumb and another finger (index or middle finger), a simple control signal constructed from finger-thumb opposition is proposed, and shown to realize stable grasping in a dynamic sense without using object information or external sensing (this is called "blind grasp" in this paper). The stability of grasping with force/torque balance under non-holonomic constraints is analyzed on the basis of a new concept named "stability on a manifold". Preliminary simulation results are shown to verify the validity of the theoretical results.
文摘The time-domain BEM was developed to analyze the dynamic stress intensity factor ( DSIF) of 3-D elastodynamic crack problems. To simulate the stress singularity along the front of a crack, eight-node isoparametric singular elements were used, and the DSIF for a semi-circular surface crack was firstly calculated based on displacement equation using the time-domain BEM formulation. The new scheme to determine the time step was brought forward. By the dynamic analysis program of time-domain BEM compiled by its, several numerical examples are presented, which demonstrate the unconditional stability and high accuracy of time-domain BEM applied to 3-D elastodynamic crack problems.
基金National Natural Science Foundation of China(41405062, 41775017)。
文摘Previous studies showed that 4 D-Var technique used for data assimilation could be modified for weather control. This study demonstrates the ability of 4 D-Var to influence the future path of a tropical cyclone by calculating perturbations in WRF simulation. Given the background error covariance matrix, the initial field is improved by the vortex dynamic initialization technique. Our results show that 4 D-Var can be applied to control the trajectory of simulated tropical cyclones by producing "optimal" perturbations. In the numerical simulation experiment of Typhoon Mitag in 2019, after this kind of weather control similar to data assimilation, the tropical cyclone moved obviously,and the damaging wind over the coastline weakened. The prediction results after the initial field modified by 4 D-Var have a great change, and the position of the tropical cyclone moved about 0.5° southeastward after assimilation,which misses the southeast coast of China. Moreover, the damaging wind is also weakened. Since the 4 D-Var is premised on the assumption that the model is perfect and does not consider the model error, then the research plan to consider model error and introduce new methods is discussed in the paper.
基金financial support from National Natural Science Foundation of China(Grant No.51835004 and 51575197)Huaqiao University International Cultivation Program for Outstanding Postgraduates and Subsidized Projec for Postgraduates’Innovative Fund in Scientific Research of Huaqiao University(No.18011080010)。
文摘Single crystal silicon carbide(SiC)is widely used for optoelectronics applications.Due to the anisotropic characteristics of single crystal materials,the C face and Si face of single crystal SiC have different physical properties,which may fit for particular application purposes.This paper presents an investigation of the material removal and associated subsurface defects in a set of scratching tests on the C face and Si face of 4H-SiC and 6H-SiC materials using molecular dynamics simulations.The investigation reveals that the sample material deformation consists of plastic,amorphous transformations and dislocation slips that may be prone to brittle split.The results showed that the material removal at the C face is more effective with less amorphous deformation than that at the Si face.Such a phenomenon in scratching relates to the dislocations on the basal plane(0001)of the SiC crystal.Subsurface defects were reduced by applying scratching cut depths equal to integer multiples of a half molecular lattice thickness,which formed a foundation for selecting machining control parameters for the best surface quality.
文摘To investigate the mechanisms of microwave induced pacemaker cell injuries, Wistar rats and the primary pacemaker cells of newborn Wistar rats were exposed to microwave at average power density of 50 mW/cm2. Slower spontaneous beating rate, intercellular Ca2+ aggregation and cell membrane perforation were detected immediately after the exposure. Moreover, hyperpolarizationactivated cyclic nucleotide-gated cation channel 4 (HCN4) was down-regulated immediately after the exposure and up-regulated at 12 h after the exposure. In the sinoatrial node (SAN) of the rats,
基金support of the Major Basic Research Programs of National Security.
文摘A cellular automaton (CA) model is established to simulate dynamic recrystallization (DRX) in the β single-phase field of Ti6Al4 V alloy, and the kinetics during DRX processing has been analyzed. The model employed considers the influences of dynamic recovery, nucleation rate, strain rate and dislocation density on DRX, and practical deformation parameters, such as temperature, strain and strain rate on DRX have been considered in the simulation. The simulated DRX grain size and DRX grain shape agree well with the experimental results, which shows the availability and lea- sibility of the cellular automaton method for the simulation of DRX. The result of kinetics analysis of DRX reveals that the Avrami exponent is variable ranging from 2.4 to 2.9, which increases with the increase of strain rate.
基金Supported by the United National Science Funds and Civil Aviation Funds(U1633104)Tianjin Science Funds for the Special of Science&Technology(17JCTPJC51800)+3 种基金Open Funds of the State Key Lab of Digital Manufacturing Equipment&Technology(DMETKF2017018)the Scientific Research Project of Tianjin Educational Committee(2019KJ119)the Fundamental Research Funds for the Central Universities(3122017017)Research Starting Funds of Civil Aviation University of China(09QD05S)。
文摘The dynamic mechanical properties of the Ti-6Al-4V(TC4)alloy prepared by laser additive manufacturing(LAM-TC4)under the high strain rate(HSR)are proposed.The dynamic compression experiments of LAM-TC4 are conducted with the split Hopkinson pressure bar(SHPB)equipment.The results show that as the strain rate increases,the widths of the adiabatic shear band(ASB),the micro-hardness,the degree of grain refinement near the ASB,and the dislocation density of grains grow gradually.Moreover,the increase of dislocation density of grains is the root factor in enhancing the yield strength of LAM-TC4.Meanwhile,the heat produced from the distortion and dislocations of grains promotes the heat softening effect favorable for the recrystallization of grains,resulting in the grain refinement of ASB.Furthermore,the contrastive analysis between LAM-TC4 and TC4 prepared by forging(F-TC4)indicates that under the HSR,the yield strength of LAM-TC4 is higher than that of F-TC4.
文摘The synthesis of new 4-imino-4H-chromeno[2,3-d]pyrimidin-3(5H)-amine in four steps including one step under microwave dielectric heating is reported. The structural identity of the synthesized compounds was established according to their spectroscopic analysis, such as FT-IR, NMR and mass spectroscopy. These new compounds were tested for their antiproliferative activities on seven representative human tumoral cell lines (Huh7 D12, Caco2, MDA-MB231, MDA-MB468, HCT116, PC3 and MCF7) and also on fibroblasts. Among them, only the compounds 6c showed micromolar cytotoxic activity on tumor cell lines (1.8 50 50 > 25 μM). Finally, in silico ADMET studies ware performed to investigate the possibility of using of the identified compound 6c as potential anti-tumor compound.
基金the financial supports from the National Natural Science Foundation of China (Nos. 52001163, 52075237)the Primary Research and Development Plan of Jiangsu Province, China (No. BE2019119)
文摘Hot deformation behaviors and microstructure evolution of Ti-3Al-5Mo-4Cr-2Zr-1Fe(Ti-35421)alloy in theβsingle field are investigated by isothermal compression tests on a Gleeble-3500 simulator at temperatures of 820-900°C and strain rates of 0.001-1 s^(-1).The research results show that discontinuous yield phenomenon and rheological softening are affected by the strain rates and deformation temperatures.The critical conditions for dynamic recrystallization and kinetic model of Ti-35421 alloy are determined,and the Arrhenius constitutive model is constructed.The rheological behaviors of Ti-35421 alloys aboveβphase transformation temperature are predicted by the constitutive model accurately.The EBSD analysis proves that the deformation softening is controlled by dynamic recovery and dynamic recrystallization.In addition,continuous dynamic recrystallization is determined during hot deformation,and the calculation model for recrystallization grain sizes is established.Good linear dependency between the experimental and simulated values of recrystallized grain sizes indicates that the present model can be used for the prediction of recrystallized grain size with high accuracy.
基金Supported by the National Natural Science Founda-tion of China (60132030)
文摘The main research motive is to analysis and to veiny the inherent nonlinear character of MPEG-4 video. The power spectral density estimation of the video trafiic describes its 1/f^β and periodic characteristics.The priraeipal compohems analysis of the reconstructed space dimension shows only several principal components can be the representation of all dimensions. The correlation dimension analysis proves its fractal characteristic. To accurately compute the largest Lyapunov exponent, the video traffic is divided into many parts.So the largest Lyapunov exponent spectrum is separately calculated using the small data sets method. The largest Lyapunov exponent spectrum shows there exists abundant nonlinear chaos in MPEG-4 video traffic. The conclusion can be made that MPEG-4 video traffic have complex nonlinear be havior and can be characterized by its power spectral density,principal components, correlation dimension and the largest Lyapunov exponent besides its common statistics.
文摘An improved three-dimensional (3-D) experimental visualization methodology is presented tor evaluating the fracture mechanisms of ferritic stainless steels by in-situ tensile testing with an environmental scanning electron microscope (ESEM). The samples were machined with a radial notched shape and a sloped surface. Both planar surface deformation and sloping surface deformation-induced microvoids were observed during dynamic tension experiments, where a greater amount of information could be obtained from the sloping surface. The results showed that microvoids formed at the grain boundaries of highly elongated large grains. The microvoids nucleated in the severely deformed regions grew nearly parallel to the tensile axis, predominantly along the grain boundaries. The microvoids nucleated at the interface of particles and the matrix did not propagate due to the high plasticity of the matrix. The large microvoids propagated and showed a zigzag shape along the grain boundaries,seemingly a consequence of the fracture of the slip bands caused by dislocation pile-ups. The final failure took place due to the reduction of the load-beating area.