The concept of legged-robot stability training with a training platform is proposed and a serial-parallel mechanism platform with 6 degrees of freedom is designed for this target. The designed platform is composed of ...The concept of legged-robot stability training with a training platform is proposed and a serial-parallel mechanism platform with 6 degrees of freedom is designed for this target. The designed platform is composed of 4-DOF parallel mechanism with spherical joints and prismatic pairs,and 2-DOF serial mechanism with prismatic pairs. With this design,the platform has advantages of low platform countertop,big workspace,high carrying capacity and high stiffness. On the basis of DOF analysis and computation of space mechanism,weight supporting auxiliary mechanism and raceways-balls supporting mechanism are designed,so as to improve the stiffness of designed large platform and payload capacity of servo motors. And then the whole structure design work of the platform is done. Meanwhile,this paper derives the analytical solutions of forward kinematics, inverse kinematics and inverse dynamics. The error analysis model of position and orientation is established. And then the simulation is done in ADAMS to ensure the correctness and feasibility of this design.展开更多
Some approaches to measure parallel 6-degree of freedom platform's posturestatically and to calibrate the platform's actual structural parameters by measuring a series of theplatform's varying postures are...Some approaches to measure parallel 6-degree of freedom platform's posturestatically and to calibrate the platform's actual structural parameters by measuring a series of theplatform's varying postures are studied. In the case where high posture accuracy is requiredrelatively, to obtain the platform's actual structural parameters is very important. Threedimensions measurement with 2 theodolites are used to obtain the platform's postures statically andNewton iterative method is adopted to calibrate structural parameters. Some measures taken in themeasurement and the calibration are discussed in detail. And the experiment results of theplatform's posture control before and after the calibration are given. The results show that theplatform's posture control accuracy after the calibration is improved notably.展开更多
A new 6-DOF micro-manipulation robot based on 3-PPTTRS parallel mechanisms in combination with flexure hinges is proposed. The design principle of the mechanism is introduced, and the kinematics analysis method based ...A new 6-DOF micro-manipulation robot based on 3-PPTTRS parallel mechanisms in combination with flexure hinges is proposed. The design principle of the mechanism is introduced, and the kinematics analysis method based on differentiation is used to get the (inverse) kinematics equations. Then a micro-scale motion precision simulation method is proposed according to finite element analysis (FEA), and the prediction of robot’s motion precision in design phase is realized. The simulation result indicates that the 6-DOF micro-manipulation robot can meet the design specification.展开更多
The trajectory tracking control for a 6-DOF robot manipulator with multiple inputs and outputs,non-linearity and strong coupling is studied.Firstly,a dynamical model for the 6-DOF robot manipulator is designed.From th...The trajectory tracking control for a 6-DOF robot manipulator with multiple inputs and outputs,non-linearity and strong coupling is studied.Firstly,a dynamical model for the 6-DOF robot manipulator is designed.From the view point of practical engineering,considering the model uncertainties and external disturbances,the robot manipulator is divided into 6 independent joint subsystems,and a linear active disturbance rejection controller(LADRC)is developed to track trajectory for each subsystem respectively.LADRC has few parameters that are easy to be adjusted in engineering.Linear expansion state observer(LESO)as the uncertainty observer is able to estimate the general uncertainties effectively.Eventually,the validity and robustness of the proposed method adopted in 6-DOF robot manipulator are demonstrated via numerical simulations and 6-DOF robot manipulator experiments,which is of practical value in engineering application.展开更多
针对奇台110 m口径全可动射电望远镜(QiTai radio Telescope,QTT)天线副面调整机构的技术指标,文中提出了一种基于6-UPS并联机器人的副面调整机构。分别利用多刚体动力学分析和控制仿真软件对副面调整机构进行了虚拟样机建模和动力学仿...针对奇台110 m口径全可动射电望远镜(QiTai radio Telescope,QTT)天线副面调整机构的技术指标,文中提出了一种基于6-UPS并联机器人的副面调整机构。分别利用多刚体动力学分析和控制仿真软件对副面调整机构进行了虚拟样机建模和动力学仿真,得出副面调整机构运动关节在天线指天和仰平两种工况下从零位运动至指定位姿所需要的最大驱动力。进一步建立了大射电望远镜副面调整机构的有限元模型,对其零位时的结构进行了模态分析,得到了前6阶固有频率,为工程设计提供了理论参考。展开更多
基金Sponsored by the National High-Tech Research and Development Program(Grant No.2006AA04Z201)
文摘The concept of legged-robot stability training with a training platform is proposed and a serial-parallel mechanism platform with 6 degrees of freedom is designed for this target. The designed platform is composed of 4-DOF parallel mechanism with spherical joints and prismatic pairs,and 2-DOF serial mechanism with prismatic pairs. With this design,the platform has advantages of low platform countertop,big workspace,high carrying capacity and high stiffness. On the basis of DOF analysis and computation of space mechanism,weight supporting auxiliary mechanism and raceways-balls supporting mechanism are designed,so as to improve the stiffness of designed large platform and payload capacity of servo motors. And then the whole structure design work of the platform is done. Meanwhile,this paper derives the analytical solutions of forward kinematics, inverse kinematics and inverse dynamics. The error analysis model of position and orientation is established. And then the simulation is done in ADAMS to ensure the correctness and feasibility of this design.
基金This project is supported by National Defense Science and Technology Multi-vocation Foundation in Advance Research of China(No. 97J465JW0408).
文摘Some approaches to measure parallel 6-degree of freedom platform's posturestatically and to calibrate the platform's actual structural parameters by measuring a series of theplatform's varying postures are studied. In the case where high posture accuracy is requiredrelatively, to obtain the platform's actual structural parameters is very important. Threedimensions measurement with 2 theodolites are used to obtain the platform's postures statically andNewton iterative method is adopted to calibrate structural parameters. Some measures taken in themeasurement and the calibration are discussed in detail. And the experiment results of theplatform's posture control before and after the calibration are given. The results show that theplatform's posture control accuracy after the calibration is improved notably.
基金the Research Fund for the Doctoral Programof Higher Education(20060007023)
文摘A new 6-DOF micro-manipulation robot based on 3-PPTTRS parallel mechanisms in combination with flexure hinges is proposed. The design principle of the mechanism is introduced, and the kinematics analysis method based on differentiation is used to get the (inverse) kinematics equations. Then a micro-scale motion precision simulation method is proposed according to finite element analysis (FEA), and the prediction of robot’s motion precision in design phase is realized. The simulation result indicates that the 6-DOF micro-manipulation robot can meet the design specification.
基金Supported by the National Natural Science Foundation of China(No.11672290)
文摘The trajectory tracking control for a 6-DOF robot manipulator with multiple inputs and outputs,non-linearity and strong coupling is studied.Firstly,a dynamical model for the 6-DOF robot manipulator is designed.From the view point of practical engineering,considering the model uncertainties and external disturbances,the robot manipulator is divided into 6 independent joint subsystems,and a linear active disturbance rejection controller(LADRC)is developed to track trajectory for each subsystem respectively.LADRC has few parameters that are easy to be adjusted in engineering.Linear expansion state observer(LESO)as the uncertainty observer is able to estimate the general uncertainties effectively.Eventually,the validity and robustness of the proposed method adopted in 6-DOF robot manipulator are demonstrated via numerical simulations and 6-DOF robot manipulator experiments,which is of practical value in engineering application.
文摘针对奇台110 m口径全可动射电望远镜(QiTai radio Telescope,QTT)天线副面调整机构的技术指标,文中提出了一种基于6-UPS并联机器人的副面调整机构。分别利用多刚体动力学分析和控制仿真软件对副面调整机构进行了虚拟样机建模和动力学仿真,得出副面调整机构运动关节在天线指天和仰平两种工况下从零位运动至指定位姿所需要的最大驱动力。进一步建立了大射电望远镜副面调整机构的有限元模型,对其零位时的结构进行了模态分析,得到了前6阶固有频率,为工程设计提供了理论参考。
基金NNSF(National Natural Science Foundation of China)under Grant 51305153 and 51575219Research Fund of Jilin science and Technology Office(KJT2016-2)+1 种基金Research Fund of Jilin provincial development and Reform Commission(2015Y067)Research Fund of Jilin Provincial Department of education 12th Five-Year funded project(2015079)
