Lap joints with a 1 mm^2 cross-sectional area were fabricated using Cu particle enhancemem 63Sn37Pb based composite solder and 63Sn37Pb eutectic solder to examine the influence of stress on the creep behavior of the s...Lap joints with a 1 mm^2 cross-sectional area were fabricated using Cu particle enhancemem 63Sn37Pb based composite solder and 63Sn37Pb eutectic solder to examine the influence of stress on the creep behavior of the solder joints. The results indicate that the creep resistance of the composite solder joints is generally superior to that of the conventional 63Sn37Pb solder joints. At the same time, the creep rupture life of the composite solder joints is declined with increasing stress and drops faster than that of the 63Sn37Pb eutectic solder joints.展开更多
The experimental tests of tensile for lead-flee solder Sn-3.5Ag were performed for the general work temperatures range from 11 to 90 ℃ and strain rate range from 5 × 10^-5 to 2 × 10^-2s^-1, and its stress--...The experimental tests of tensile for lead-flee solder Sn-3.5Ag were performed for the general work temperatures range from 11 to 90 ℃ and strain rate range from 5 × 10^-5 to 2 × 10^-2s^-1, and its stress--strain curves were compared to those of solder Sn-37Pb. The parameters in Anand model for solder Sn-3.5Ag were fitted based on experimental data and nonlinear fitting method, and its validity was checked by means of experimental data. Furthermore, the Anand model was used in the FEM analysis to evaluate solder joint thermal cycle reliability. The results show that solder Sn-3.5Ag has a better creep resistance than solder Sn-37Pb. The maximum stress is located at the upper right comer of the outmost solder joint from the symmetric center, and thermal fatigue life is predicted to be 3.796 × 10^4 cycles under the calculated conditions.展开更多
Creep property of solder alloys is one of the important factors to affect the reliabdity of soldered joints in SMT （surface mount technology）. Particle-enhancement is a way to improve the properties of solder alloys...Creep property of solder alloys is one of the important factors to affect the reliabdity of soldered joints in SMT （surface mount technology）. Particle-enhancement is a way to improve the properties of solder alloys and has caused much more attention than before. Temperatures applied to soldered joints are one of the primary factors of affecting creep properties of particle enhancement composite soldered joints. In this paper single shear lap creep specimens with a 1 mm^2 cross-sectional area were fabricated using Cu particle enhancement 63Sn37 Pb based composite soldered joints and 63Sn37 Pb eutectic soldered joints to examine the influence of temperature on creep behavior of soldered joints. Results indicated that the creep resistance of soldered joints of Cu particle enhancement 63Sn37Pb based composite soldered joint was generally superior to that of the conventional 63Sn37Pb soldered joint. At the same time, creep rupture life of the composite soldered joint was declined with increasing temperature and drop faster than that of the conventional 63Sn37 Pb eutectic soldered joint.展开更多
基金This study is financially supported by the Foundation of Henan University of Science & Technology(No.13420060) Luoyang Advanced Hydraulic Pressure Technology Ltd. ( 6142004).
文摘Lap joints with a 1 mm^2 cross-sectional area were fabricated using Cu particle enhancemem 63Sn37Pb based composite solder and 63Sn37Pb eutectic solder to examine the influence of stress on the creep behavior of the solder joints. The results indicate that the creep resistance of the composite solder joints is generally superior to that of the conventional 63Sn37Pb solder joints. At the same time, the creep rupture life of the composite solder joints is declined with increasing stress and drops faster than that of the 63Sn37Pb eutectic solder joints.
基金Project(50376076) supported by the National Natural Science Foundation of China
文摘The experimental tests of tensile for lead-flee solder Sn-3.5Ag were performed for the general work temperatures range from 11 to 90 ℃ and strain rate range from 5 × 10^-5 to 2 × 10^-2s^-1, and its stress--strain curves were compared to those of solder Sn-37Pb. The parameters in Anand model for solder Sn-3.5Ag were fitted based on experimental data and nonlinear fitting method, and its validity was checked by means of experimental data. Furthermore, the Anand model was used in the FEM analysis to evaluate solder joint thermal cycle reliability. The results show that solder Sn-3.5Ag has a better creep resistance than solder Sn-37Pb. The maximum stress is located at the upper right comer of the outmost solder joint from the symmetric center, and thermal fatigue life is predicted to be 3.796 × 10^4 cycles under the calculated conditions.
文摘Creep property of solder alloys is one of the important factors to affect the reliabdity of soldered joints in SMT （surface mount technology）. Particle-enhancement is a way to improve the properties of solder alloys and has caused much more attention than before. Temperatures applied to soldered joints are one of the primary factors of affecting creep properties of particle enhancement composite soldered joints. In this paper single shear lap creep specimens with a 1 mm^2 cross-sectional area were fabricated using Cu particle enhancement 63Sn37 Pb based composite soldered joints and 63Sn37 Pb eutectic soldered joints to examine the influence of temperature on creep behavior of soldered joints. Results indicated that the creep resistance of soldered joints of Cu particle enhancement 63Sn37Pb based composite soldered joint was generally superior to that of the conventional 63Sn37Pb soldered joint. At the same time, creep rupture life of the composite soldered joint was declined with increasing temperature and drop faster than that of the conventional 63Sn37 Pb eutectic soldered joint.
