A 16 bit Stereo Audio ΣΔ A/D Converter

A 16 bit stereo audio novel stability fifth-order ∑△ A/D converter that consists of switched capacitor ∑△ modulators, a decimation filter, and a bandgap circuit is proposed. A method for the stabilization of a high order single stage ∑△ modulator is also proposed. A new multistage comb filter is used for the front end decimation filter. The ∑△ A/D converter achieves a peak SNR of 96dB and a dynamic range of 96dB. The ADC was implemented in 0. 5μm 5V CMOS technology. The chip die area occupies only 4. 1mm × 2.4mm and dissipates 90mW.

Propagations of Fresnel diffraction accelerating beam in Schrodinger equation with nonlocal nonlinearity

Accelerating beams have been the subject of extensive research in the last few decades because of their selfacceleration and diffraction-free propagation over several Rayleigh lengths.Here,we investigate the propagation dynamics of a Fresnel diffraction beam using the nonlocal nonlinear Schrodinger equation(NNLSE).When a nonlocal nonlinearity is introduced into the linear Schrodinger equation without invoking an external potential,the evolution behaviors of incident Fresnel diffraction beams are modulated regularly,and certain novel phenomena are observed.We show through numerical calculations,under varying degrees of nonlocality,that nonlocality significantly affects the evolution of Fresnel diffraction beams.Further,we briefly discuss the two-dimensional case as the equivalent of the product of two one-dimensional cases.At a critical point,the Airy-like intensity profile oscillates between the first and third quadrants,and the process repeats during propagation to yield an unusual oscillation.Our results are expected to contribute to the understanding of NNLSE and nonlinear optics.

Locating Sources of Oscillations Induced by Control of Voltage Source Converters Based on Energy Structure and Nonlinearity Detection

The oscillation phenomena associated with the control of voltage source converters(VSCs)are concerning,making it crucial to locate the sources of such oscillations and suppress the oscillations.Therefore,this paper presents a location scheme based on the energy structure and nonlinearity detection.The energy structure,which conforms to the principle of the energy-based method and dissipativity theory,is developed to describe the transient energy flow for VSCs,based on which a defined characteristic quantity is implemented to narrow the scope for locating the sources of oscillations.Moreover,based on the self-sustained oscillation characteristics of VsCs,an index for nonlinearity detection is applied to locate the VSCs that produce the oscillation energy.The combination of the energy structure and nonlinearity detection distinguishes the contribu-tions of different VSCs to the oscillation.The results of a case study implemented by the PSCAD/EMTDC simulation validate theproposed scheme.

The Design of A/D Converter Circuit Adopting the Technology of PWM

This text has expounded the working principle of realizing A/D conversion that utilizes the timer within MCU and combinesthe technology of PWM. The design of hardware circuit, improved gradual approached trial arithmetic and relevant program design arediscussed in detail. And it has analyzed the resolution of A/D converter based on the technology of PWM, etc.

Negative Stiffness Mechanism on An Asymmetric Wave Energy Converter by Using A Weakly Nonlinear Potential Model

Salter's duck,an asymmetrical wave energy converter(WEC)device,showed high efficiency in extracting energy from 2D regular waves in the past;yet,challenges remain for fluctuating wave conditions.These can potentially be addressed by adopting a negative stiffness mechanism(NSM)in WEC devices to enhance system efficiency,even in highly nonlinear and steep 3D waves.A weakly nonlinear model was developed which incorporated a nonlinear restoring moment and NSM into the linear formulations and was applied to an asymmetric WEC using a time domain potential flow model.The model was initially validated by comparing it with published experimental and numerical computational fluid dynamics results.The current results were in good agreement with the published results.It was found that the energy extraction increased in the range of 6%to 17%during the evaluation of the effectiveness of the NSM in regular waves.Under irregular wave conditions,specifically at the design wave conditions for the selected test site,the energy extraction increased by 2.4%,with annual energy production increments of approximately 0.8MWh.The findings highlight the potential of NSM in enhancing the performance of asymmetric WEC devices,indicating more efficient energy extraction under various wave conditions.

Fully Nonlinear Time Domain Analysis for Hydrodynamic Performance of An Oscillating Wave Surge Converter

The hydrodynamic behaviour of an oscillating wave surge converter(OWSC) in large motion excited by nonlinear waves is investigated. The mechanism through which the wave energy is absorbed in the nonlinear system is analysed. The mathematical model used is based on the velocity potential theory together with the fully nonlinear boundary conditions on the moving body surface and deforming free surface. The problem is solved by the boundary element method. Numerical results are obtained to show how to adjust the mechanical properties of the OWSC to achieve the best efficiency in a given wave, together with the nonlinear effect of the wave height. Numerical results are also provided to show the behaviour of a given OWSC in waves of different frequencies and different heights.

A 12bit 300MHz Current-Steering CMOS D/A Converter

The proposed DAC consists of a unit current-cell matrix for 8MSBs and a binary-weighted array for 4LSBs,trading-off between the precision,speed,and size of the chip.In order to ensure the linearity of the DAC,a double Centro symmetric current matrix is designed by the Q2 random walk strategy.To achieve better dynamic performance,a latch is added in front of the current switch to change the input signal,such as its optimal cross-point and voltage level.For a 12bit resolution,the converter reaches an update rate of 300MHz.

Wave Extraction and Attenuation Performance of An Edinburgh Duck Wave Energy Converter

Edinburgh Duck wave energy converter(ED WEC)has excellent energy extraction performance and shows a great potential to integrate with other marine structures.This paper aims to investigate its wave energy extraction performance as a WEC and wave attenuation performance as a protection method for shoreline or marine structures.The wave and ED WEC interactions in regular waves are modeled using the Star-CCM+software and verified by comparisons with published experimental results.The motion response,energy conversion efficiency,and transmission coefficient of the ED WEC with different attack angles,rotation center,and incident wave heights are investigated.Results indicate that the ED WEC with an attack angle of 42°and a rotation center of 0.55 m below the mean water line can achieve both good wave energy extraction and wave attenuation performances.The wave energy extraction and wave attenuation performance of the ED WEC decrease significantly with the increase of wave nonlinearity characterized by the wave steepness.This paper can guide the practical application of the ED WEC at the early stage of design.

A 10-bit low power SAR A/D converter based on 90 nm CMOS

Traditional and some recently reported low power,high speed and high resolution approaches for SAR A/D converters are discussed.Based on SMIC 65 nm CMOS technology,two typical low power methods reported in previous works are validated by circuit design and simulation.Design challenges and considerations for high speed SAR A/D converters are presented.Moreover,an R–C combination based method is also addressed and a 10-bit SAR A/D converter with this approach is implemented in SMIC 90 nm CMOS process.The DNL and INL are measured to be less than 0.31 LSB and 0.59 LSB respectively.With an input frequency of 420 kHz at 1 MS/s sampling rate, the SFDR and ENOB are measured to be 67.6 dB and 9.46 bits respectively,and the power dissipation is measured to be just 3.17 mW.

Analysis of the Hydrodynamic Performance of an Oyster Wave Energy Converter Using Star-CCM+

A two-dimensional numerical Computational Fluid Dynamics(CFD)model is established on the basis of viscous CFD theory to investigate the motion response and power absorption performance of a bottom-hinged flap-type wave energy converter(WEC)under regular wave conditions.The convergence study of mesh size and time step is performed to ensure that wave height and motion response are sufficiently accurate.Wave height results reveal that the attenuation of wave height along the wave tank is less than 5%only if the suitable mesh size and time step are selected.The model proposed in this work is verified against published experimental and numerical models.The effects of mechanical damping,wave height,wave frequency,and water depth on the motion response,power generation,and energy conversion efficiency of the flap-type WEC are investigated.The selection of the appropriate mechanical damping of the WEC is crucial for the optimal extraction of wave power.The optimal mechanical damping can be readily predicted by using potential flow theory.It can then be verified by applying CFD numerical results.In addition,the motion response and the energy conversion efficiency of the WEC decrease as the incident wave height increases because the strengthened nonlinear effect of waves intensifies energy loss.Moreover,the energy conversion efficiency of theWEC decreases with increasing water depth and remains constant as the water depth reaches a critical value.Therefore,the selection of the optimal parameters during the design process is necessary to ensure that the WEC exhibits the maximum energy conversion efficiency.

Numeric Simulation of Single Passage Ternary Turbulence Model in Hydraulic Torque Converter

Based on the renormalization group theory, a hydraulic torque converter 3 D turbulent single flow passage model is constructed and boundary condition is determined for analyzing the influence of the fluid field characteristic and parameters on the macroscopic model. Numerical simulation of the single fluid path is processed by computational fluid dynamics and the calculated results approach to experimental data well, and especially in low transmission ratio the torque and head results are more close to experimental data than the calculated results of beam theory. This shows that the appropriate ternary analysis method and reasonable assumption of boundary condition may analyze the flow field more precisely and predict the performance of torque converter more accurately.

Capture Performance of A Multi-Freedom Wave Energy Converter with Different Power Take-off Systems

Among the wave energy converters (WECs), oscillating buoy is a promising type for wave energy development in offshore area. Conventional single-freedom oscillating buoy WECs with linear power take-off (PTO) system are less efficient under off-resonance conditions and have a narrow power capture bandwidth. Thus, a multi-freedom WEC with a nonlinear PTO system is proposed. This study examines a multi-freedom WEC with 3 degrees of freedom: surge, heave and pitch. Three different PTO systems (velocity-square, snap through, and constant PTO systems) and a traditional linear PTO system are applied to the WEC. A time-domain model is established using linear potential theory and Cummins equation. The kinematic equation is numerically calculated with the fourth-order Runge–Kutta method. The optimal average output power of the PTO systems in all degrees of freedom are obtained and compared. Other parameters of snap through PTO are also discussed in detail. Results show that according to the power capture performance, the order of the PTO systems from the best to worst is snap through PTO, constant PTO, linear PTO and velocity-square PTO. The resonant frequency of the WEC can be adjusted to the incident wave frequency by choosing specific parameters of the snap through PTO. Adding more DOFs can make the WEC get a better power performance in more wave frequencies. Both the above two methods can raise the WEC’s power capture performance significantly.

A 10bit 2GHz CMOS D/A Converter for High-Speed System Applications

This paper presents a 2GS/s 10bit CMOS digital-to-analog converter （DAC） that consists of two unit current-cell matrixes for 6MSBs and 4LSBs, respectively, trading off between the precision and size of the chip. Current mode logic （CML） is used to ensure high speed,and a double centro-symmetric current matrix is designed by the Q^2 random walk strategy in order to ensure the linearity of the DAC. The DAC occupies 2.2mm × 2.2mm of die area and consumes 790mW with a single 3.3V power supply.

A novel method for predicting the power outputs of wave energy converters

This paper focuses on realistically predicting the power outputs of wave energy converters operating in shallow water nonlinear waves. A heaving two-body point absorber is utilized as a specific calculation example, and the generated power of the point absorber has been predicted by using a novel method（a nonlinear simulation method） that incorporates a second order random wave model into a nonlinear dynamic filter. It is demonstrated that the second order random wave model in this article can be utilized to generate irregular waves with realistic crest–trough asymmetries, and consequently, more accurate generated power can be predicted by subsequently solving the nonlinear dynamic filter equation with the nonlinearly simulated second order waves as inputs. The research findings demonstrate that the novel nonlinear simulation method in this article can be utilized as a robust tool for ocean engineers in their design, analysis and optimization of wave energy converters.

NEW PERTURBATION TECHNIQUE FOR TRANSIENT ANALYSIS AND ITS APPLICATIONS IN DC-DC PWM SWITCHING POWER CONVERTERS

An improved perturbation technique proposed in a recent paper (Int. J. Electronics, vol. 63, pp.403-414) has been successfully applied to steady-state analysis of PWM switching converters. This paper extends the algorithm to transient analysis of a broader class of non-linear systems. As an example, the transient response of a Boost PWM switching converter is analyzed to demonstrate its simplicity and accuracy.

Wave Slamming on An OWSC Wave Energy Converter in Coupled Wave-Current Conditions with Variable-Depth Seabed

Coastal wave energy resources have enormous exploitation potential due to shorter weather window,closer installation distance and lower maintenance cost.However,impact loads generated by depth variation from offshore to nearshore and wave-current interaction,may lead to a catastrophic damage or complete destruction to wave energy converters(WECs).This objective of this paper is to investigate slamming response of a coastal oscillating wave surge converter(OWSC)entering or leaving water freely.Based on fully nonlinear potential flow theory,a time-domain wave-current-structure interaction model combined with higher-order boundary element method(HOBEM),is developed to analyze the coupled hydrodynamic problem.The variable-depth seabed is considered in the model to illustrate the shallow water effect on impact loads and free surface profiles in coastal zone.A domain decomposition approach is utilized to simulate the overlapping phenomenon generated by a jet falling into water under gravity effect.Through a series of Lagrangian interpolation methods,the meshes on boundaries are rearranged to avoid the mismatch between element size on free surface and body surface.The present model is validated against the existing experimental and numerical results.Simulations are also provided for the effects of wave-current interaction and uneven local seabed on the slamming responses.It is found that the length of the splash jet increases for a following current and decreases for an opposing current,and that the slamming response of the OWSC device is sensitive to the geometric features of the uneven seabed.

Performance Optimization of Torque Converters Based on Modified 1D Flow Model

A methodology for performance optimization of torque converters is put forward based on the one-dimensional (1D) flow model. It is found that the inaccuracy of 1D flow model for predicting hydraulic performance at the low speed ratio is mainly caused by the separation phenomenon at the stator cascade which is induced by large flow impinging at the pressure side of the stator blades. A semi-empirical separation model is presented and incorporated to the original 1D flow model. It is illustrated that the improved model is able to predict the circumferential velocity components accurately, which can be applied to performance optimization. Then, the Pareto front is obtained by using the genetic algorithm (GA) in order to inspect the coupled relationship among stalling impeller torque capacity, stalling torque ratio and efficiency. The efficiency is maximized on the premise that a target stalling impeller torque capacity and torque ratio are achieved. Finally, the optimized result is verified by the computational fluid dynamics(CFD) simulation, which indicates that the maximal efficiency is increased by 0.96%.

Numerical simulation of the flow field of a flat torque converter

A flexible flat torque converter was proposed to fulfill the requirement of miniaturization and power density maximization for automobiles.Constructed by two arcs joined by lines,the torus was designed directly from design path.The influence of flatness on the performance of the torque converter was evaluated.The software CFX and standard k-ε model were adopted to simulate the internal flow fields of the torque converter under different flatness ratios.The results indicated that the performance of the torque converter got worse as the flatness declined,but the capacity of pump increased.The efficiency and the torque ratio dropped slightly as the flatness ratio decreased.So the torque converter could be squashed appropriately to get high power density without too much efficiency sacrifice.But when the flatness ratio was below 0.2,there was a significant drop in the efficiency.

Analytical Modelling and Experiment of Novel Rotary Electro-Mechanical Converter with Negative Feedback Mechanism for 2D Valve

The manufacturing of spiral groove structure of two-dimensional valve(2D valve)feedback mechanism has shortcomings of both high cost and time-consuming.This paper presents a novel configuration of rotary electro-mechanical converter with negative feedback mechanism(REMC-NFM)in order to replace the feedback mechanism of spiral groove and thus reduce cost of valve manufacturing.In order to rapidly and quantitative evaluate the driving and feedback performance of the REMC-NFM,an analytical model taking leakage flux,edge effect and permeability nonlinearity into account is formulated based on the equivalent magnetic circuit approach.Then the model is properly simplified in order to obtain the optimal pitch angle.FEM simulation is used to study the influence of crucial parameters on the performance of REMC-NFM.A prototype of REMC-NFM is designed and machined,and an exclusive experimental platform is built.The torque-angle characteristics,torque-displacement characteristics,and magnetic flux density in the working air gap with different excitation currents are measured.The experimental results are in good agreement with the analytical and FEM simulated results,which verifies the correctness of the analytical model.For torque-angle characteristics,the overall torque increases with both current and rotation angle,which reaches about 0.48 N·m with 1.5 A and 1.5°.While for torque-displacement characteristics,the overall torque increases with current yet decrease with armature displacement due to the negative feedback mechanism,which is about 0.16 N·m with 1.5 A and 0.8 mm.Besides,experimental results of conventional torque motor are compared with counterparts of REMC-NFM in order to validate the simplified model.The research indicates that the REMC-NFM can be potentially used as the electro-mechanical converter for 2D valves in civil servo areas.

Study on Bifurcation and Chaos in Boost Converter Based on Energy Balance Model

Based on boost converter operating in discontinuous mode, this paper proposes an energy balance model (EBM) for analyzing bifurcation and chaos phenomena of capacitor energy and output voltage when the converter parameter is varying. It is found that the capacitor energy and output voltage dynamic behaviors exhibit the typical period-doubling route to chaos by increasing the feedback gain constant K of proportional controller. The accurate position of the first bifurcation point and the iterative diagram of the capacitor energy with every K can be derived from EBM. Finally, the underlying causes for bifurcations and chaos of a general class of nonlinear systems such as power converters are analyzed from the energy balance viewpoint. Com-paring with the discrete iterative model, EBM is simple and high accuracy. This model can be easily devel-oped on the nonlinear study of the other converters.