Study on Limited Filamentous Sludge Bulking Test in A/O Activated Sludge Process

[Objective] This study aimed to make use of the limited filamentous sludge bulking characteristics to purify water quality and save energy. [Method] The effects of dissolved oxygen （DO） on sludge bulking were explored by changing the DO con- centration in the aerobiotic pool of NO system from the low load （0.25 kg COD/（kg MLSS.d）） and the medium to high load （0.55 kgCOD/（kg MLSSod））. [Result] In the NO activated sludge system, when the sludge load was 0.25 kg COD/（kg MLSS.d）, DO=1.5 mg/L, the sludge index was at around 250, while when the sludge load- ing was 0.55 kg COD/（kg MLSS.d）, DO=1.5 mg/L, the sludge index was close to 300, occurring the limited filamentous bulking. The bulked sludge still showed high removal rates to COD, SS, nitrogen and phosphorus. [Conclusion] It could improve the oxygen transfer rate and reduce the aeration rate at low DO conditions to achieve energy-saving.

Synergetic Bioproduction of Short-Chain Fatty Acids from Waste Activated Sludge Intensified by the Combined Use of Potassium Ferrate and Biosurfactants

The synergetic effect and underlying mechanism of potassium ferrate(PF)with tea saponin(TS,a biosurfactant)in producing short chain fatty acids(SCFAs)from anaerobic fermentation of waste activated sludge(WAS)were explored in this work.Experimental results showed that 0.2 g PF(g TSS)^(-1)(total suspended solid)combined with 0.02 g TS(g TSS)^(-1) could further improve SCFAs’production,and the maximum SCFAs content reached 2008.7 mg COD L^(-1),which is 1.2 and 4.5 times higher than those with PF and TS individually added,respectively,and 5.3 times higher than that of blank WAS on Day 12.In the model substrates experiments,the degradation rates of bovine serum albumin and dextran with combination of PF and TS were 41.3%±0.1% and 48.5%±0.06%,respectively,on Day 3,which are lower than those in blank WAS(with degradation rates of 72.3%±0.5%and 90.3%±0.3%).It was revealed that the oxidative effect of PF and the solubilization of TS caused more organic matters to be dissolved out from WAS,providing a large number of biodegradable substances for subsequent SCFAs production.While WAS pretreated with the combination of PF and TS,the relative abundances of Firmicutes increased from 6.4%(blank)to 38.6%,and that of Proteobacteria decreased from 41.8%(blank)to 21.8%.The combination of PF and TS promoted the hydrolysis process of WAS by enriching Firmicutes,and then increased acetic acid production by inhibiting Proteobacteria that consumed SCFAs.Meanwhile,at the genus level,acidogenesis bacteria(e.g.,Proteiniclasticum and Petrimonas)were enriched whereas SCFAs consuming bacteria(e.g.,Dokdonella)were inhibited.

Study Progress Analysis of Effluent Quality Prediction in Activated Sludge Process Based on CiteSpace

In this paper, CiteSpace, a bibliometrics software, was adopted to collect research papers published on the Web of Science, which are relevant to biological model and effluent quality prediction in activated sludge process in the wastewater treatment. By the way of trend map, keyword knowledge map, and co-cited knowledge map, specific visualization analysis and identification of the authors, institutions and regions were concluded. Furthermore, the topics and hotspots of water quality prediction in activated sludge process through the literature-co-citation-based cluster analysis and literature citation burst analysis were also determined, which not only reflected the historical evolution progress to a certain extent, but also provided the direction and insight of the knowledge structure of water quality prediction and activated sludge process for future research.

Effects of Potassium Ferrate and Low-Temperature Thermal Hydrolysis Co-Pretreatment on the Hydrolysis and Anaerobic Digestion Process of Waste Activated Sludge

This study evaluated the effect of potassium ferrate(PF)and low-temperature thermal hydrolysis co-pretreatment on the promotion of sludge hydrolysis process and the impact on acid production in the subsequent anaerobic digestion process.The analytical investigations showed that co-pretreatment significantly facilitated the hydrolysis process of the sludge and contributed to the accumulation of short-chain fatty acids(SCFAs).The pretreatment conditions under the optimal leaching of organic matter from sludge were hydrothermal temperature of 75℃,hydrothermal treatment time of 12 h,and PF dosage of 0.25 g g^(−1)TSS(total suspended solids),according to the results of orthogonal experiments.By pretreatment under proper conditions,the removal rate of soluble chemical oxygen demand(SCOD)achieved 71.8%at the end of fermentation and the removal rate of total phosphorus(TP)was 69.1%.The maximum yield of SCFAs was 750.3 mg L^(−1),7.45 times greater than that of the blank group.Based on the analysis of the anaerobic digestion mechanism,it was indicated that the co-pretreatment could destroy the floc structure on the sludge surface and improve organic matter dissolving,resulting in more soluble organic substances for the acidification process.Furthermore,microbial community research revealed that the main cause of enhanced SCFAs generation was an increase in acidogenic bacteria and a reduction of methanogenic bacteria.

Preliminary Study on the Treatment Efficiency of Pasteurized Lime Thermal Alkaline Hydrolysis for Excess Activated Sludge and Reduction of Tetracycline Resistance Genes

Thermal alkaline hydrolysis is a common pretreatment method for the utilization of excess activated sludge(EAS).Owing to strict environment laws and need for better energy utilization,new methods were developed in this study to improve the efficiency of pretreatment method.Direct thermal hydrolysis(TH),pasteurized thermal hydrolysis(PTH),and alkaline pasteurized thermal hydrolysis(PTH+CaO and PTH+NaOH)methods were used to treat EAS.Each method was compared and analyzed in terms of dissolution in ammonium nitrogen(NH_(4)^(+)-N)and soluble COD(SCOD)in EAS.Furthermore,the removal of tetracycline resistance genes(TRGs)and class 1 transposon gene intI1 from EAS was investigated.The NH_(4)^(+)-N and SCOD concentrations in EAS treated by PTH were 1.24 and 2.58 times higher than those of TH.However,the removal efficiency of total TRGs and intI1 between the groups was comparable.The SCOD concentration of the PTH+NaOH group was 4.37 times higher than that of the PTH group,and the removal efficiency of total TRGs was increased by 9.52%compared with that by PTH.The NH_(4)^(+)-N and SCOD concentrations of the PTH+CaO group could reach 85.04%and 92.14%of the PTH+NaOH group,but the removal efficiency of total TRGs by PTH+CaO was 19.78%lower than that by PTH+NaOH.Thus,to reduce the financial cost in actual operation,lime(CaO)can be used instead of a strong alkali(NaOH),and pasteurized steam at 70℃ instead of conventional high-temperature heating to treat EAS.This study provides a reference for the development of alkaline hydrolysis under moderate temperatures along with the removal of TRGs in EAS.

Influence of Pyrolytic Biochar on Settleability and Denitrification of Activated Sludge Process

Biochar is a massively produced by-product of biomass pyrolysis to obtain renewable energy and has not been fully used. Incomplete separation of sludge and effluent and insufficient denitrification of sewage are two of main factors that influence the efficiency of activated sludge process. In this work, we proposed a new utilization of biochar and investigated the effect of biochar addition on the performance of settleability and denitrification of activated sludge. Results show that the addition of biochar can improve the settleability of activated sludge by changing the physicochemical characteristics of sludge （e.g., flocculating ability, zeta-potential, hydrophobicity, and extracellular polymeric substances constituents）. Moreover, the dissolved organic carbon released from biochar obtained at lower pyrolysis temperature can improve the nitrate removal efficiency to a certain extent.

STUDY AND SIMULATION OF AN ACTIVATED SLUDGE TREATMENT FOR METHYL VIOLET WASTE WATER

This paper researched a promising biological treatment of methyl violet waste water by methods of activated sludge.Effects of temperature and pH were studied on this process.Kinetic equation of the substrate biodegradation was investigated in the experimental range.It was studied and simulated that flow within the bubble region of this bioreactor according to the κ ε two fluid equation.Simulation results agree well with experimental data.

Optimization of Extraction Conditions of Extracellular Polymeric Substances from Activated Sludge

[Objective] To explore the optimal extraction conditions of extracellular polymeric substances （EPS） from activated sludge. [Method] The efficiency of five methods （H2SO4, formaldehyde-NaOH, mixing, heating and NaOH） on the extraction of EPS was investigated comparatively. The optimal extraction conditions of the most suitable method were determined. [Result] NaOH method is most effective in extracting EPS with less DNA contamination and shortened extraction period. The optimal extraction condition was pH of 11, extraction time of 10 min and agitation speed of 80-120 r/min. [Conclusion] The determined optimal extraction condition provided theoretical basis for EPS study.

Biosorption of cadmium(II) and lead(II) ions from aqueous solutions onto dried activated sludge

The removal of heavy-metal ions from aqueous solutions by using dried activated sludge has been investigated in batch systems. Effect of solution pH, initial metal ion concentration, and temperature were determined. The results of the kinetic studies showed that the uptake processes of the two metal ions（Cd（Ⅱ） and Pb（Ⅱ）） followed the pseudo-second-order rate expression. The equilibrium data fitted very well to both the Langmuir and Freundlich adsorption models. The FT-IR analysis showed that the main mechanism of Cd（Ⅱ） and Pb（Ⅱ） biosorption onto dried activated sludge was their binding with amide I group.

Functions and behaviors of activated sludge extracellular polymeric substances (EPS): a promising environmental interest

Extracellular polymeric substances （EPS） are the predominant constituents of activated sludge and represent up to 80% of the mass of activated sludge. They play a crucial role in the flocculation, settling and dewatering of activated sludge. Furthermore, EPS also show great efficiency in binding heavy metals. So EPS are key factors influencing reduction in sludge volume and mass, as well as activity and utilization of sludge. EPS are of considerable environmental interest and hundreds of articles on EPS have been published abroad, while information on EPS in China is limited. In this paper, results of over 60 publications related to constituents and characteristics of EPS and their influences on flocculation, settling and dewatering of sludge are compiled and analyzed. Metal-binding ability of EPS is also discussed, together with a brief consideration of possible research interests in the future.

Start-up of anaerobic ammonia oxidation bioreactor with nitrifying activated sludge

The anaerobic ammonia oxidation(Anammox) bioreactor was successfully started up with the nitrifying activated sludge. After anaerobically operated for 105 d, the bioreactor reached a good performance with removal percentage of both ammonia and nitrite higher than 95% and volumetric total nitrogen removal as high as 149.55 mmol/(L·d). The soft padding made an important contribution to the high efficiency and stability because it held a large amount of biomass in the bioreactor.

Immobilization study of biosorption of heavy metal ions onto activated sludge

Activated sludge was immobilized into Ca-alginate beads via entrapment, and biosorption of three heavy metal ions, copper(Ⅱ), zinc(Ⅱ), and chromimum(Ⅱ), from aqueous solution in the concentration range of 10\_100 mg/L was studied by using both entrapped activated sludge and inactivated free biomass at pH≤5. A biphasic metal adsorption pattern was observed in all immobilized biomass experiments. The biosorption of metal ions by the biosorbents increased with the initial concentration increased in the medium. The adsorption rate of immobilized pre-treated activated sludge(PAS) was much lower than that of free PAS due to the increase in mass transfer resistance resulting from the polymeric matrix. Biosorption equilibrium of beads was established in about 20 h and the adsorbed heavy metal ions did not change further with time. No significant effect of temperature was observed in the test for free biomass while immobilized PAS appeared to be strong temperature dependent in the test range of 10 and 40℃. Besides, the content of activated sludge in the calcium alginate bead has an influence on the uptake of heavy metals. The sorption equilibrium was well modeled by Langmuir isotherm, implying monomolecular adsorption mechanism. Carboxyl group in cell wall played an important role in surface adsorption of heavy metal ions on PAS.

Community analysis of ammonia-oxidizing bacteria in activated sludge of eight wastewater treatment systems

We investigated the communities of ammonia-oxidizing bacteria （AOB） in activated sludge collected from eight wastewater treatment systems using polymerase chain reaction （PCR） followed by terminal restriction fragment length polymorphism （T-RFLP）, cloning, and sequencing of the α-subunit of the ammonia monooxygenase gene （amoA）. The T-RFLP fingerprint analyses showed that different wastewater treatment systems harbored distinct AOB communities. However, there was no remarkable difference among the AOB T- RFLP profiles from different parts of the same system. The T-RFLP fingerprints showed that a full-scale wastewater treatment plant （WWTP） contained a larger number of dominant AOB species than a pilot-scale reactor. The source of influent affected the AOB community, and the WWTPs treating domestic wastewater contained a higher AOB diversity than those receiving mixed domestic and industrial wastewater. However, the AOB community structure was little affected by the treatment process in this study. Phylogenetic analysis of the cloned amoA genes clearly indicated that all the dominant AOB in the systems was closely related to Nitrosomonas spp. not to Nitrosospira spp. Members of the Nitrosomonas oligotropha and Nitrosomonas communis clusters were found in all samples, while members of Nitrosomonas europaea cluster occurred in some systems.

Optimization of process parameters for the bioconversion of activated sludge by Penicillium corylophilum, using response surface methodology

The optimization of process parameters for the bioconversion of activated sludge by Penicillium corylophilum was investigated using response surface methodology （RSM）. The three parameters namely temperature of 33℃, agitation of 150 r/min, and pH of 5 were chosen as center point from the previous study of fungal treatment. The experimental data on chemical oxygen demand （COD） removal （%） were fitted into a quadratic polynomial model using multiple regression analysis. The optimum process conditions were determined by analyzing response surface three-dimensional surface plot and contour plot and by solving the regression model equation with Design Expert software. Box-Behnken design technique under RSM was used to optimize their interactions, which showed that an incubation temperature of 32.5℃, agitation of 105 r/min, and pH of 5.5 were the best conditions. Under these conditions, the maximum predicted yield of COD removal was 98.43%. These optimum conditions were used to evaluate the trail experiment, and the maximum yield of COD removal was recorded as 98.5%.

Kinetic analysis of waste activated sludge hydrolysis and short-chain fatty acids production at pH 10

The accumulation of short-chain fatty acids （SCFAs）, a preferred carbon source for enhanced biological phosphorus removal microbes, was significantly improved when waste activated sludge （WAS） was fermented at pH 10. The kinetics of WAS hydrolysis and SCFAs production at pH 10 was investigated. It was observed that during WAS anaerobic fermentation the accumulation of SCFAs was limited by the hydrolysis process, and both the hydrolysis of WAS particulate COD and the accumulation of SCFAs followed first-order kinetics. The hydrolysis and SCFAs accumulation rate constants increased with increasing temperature from 10 to 35℃, which could be described by the Arrhenius equation. The kinetic data further indicated that SCFAs production at pH 10 was a biological process. Compared with the experiment of pH uncontrolled （blank test）, both the rate constants of WAS hydrolysis and SCFAs accumulation at 20℃ were improved significantly when WAS was fermented at pH 10.

Biosorption of zinc(Ⅱ) from aqueous solution by dried activated sludge

The biosorption potential of dried activated sludge as a biosorbent for zinc（Ⅱ） removal from aqueous solution was investigated.The effects of initial pH,contact time,initial zinc ion concentration,and adsorbent dosage on the biosorption processes were determined,and the equilibrium data were modeled by the Langmuir and Freundlich isotherms.The Langmuir isotherm model （R 2=0.999） was proved to fit the equilibrium data much better than the Freundlich isotherm model （R 2=0.918）.The monolayer adsorption capacity of dried activated sludge for zinc（Ⅱ） was found to be 17.86 mg/g at pH of 5 and 25°C.The kinetic data were tested using pseudo firstand second-order models.The results suggested that the pseudo second-order model （R 2 〉 0.999） was better for the description of the adsorption behavior of zinc（Ⅱ） onto the dried activated sludge.Fourier transform infrared spectral analysis showed that the dominant mechanism of zinc（Ⅱ） biosorption onto the dried activated sludge was the binding between amide groups and zinc ions.

Simulation and assessment of sludge concentration and rheology in the process of waste activated sludge treatment

The process of using flat-sheet membrane for simultaneous sludge thickening and digestion （MSTD） was employed. The variations of sludge concentration and rheology were characterized and simulated. Based on mass balance analysis, mathematical models were developed and successfully used to predict and evaluate the variations of sludge concentration and the digestion efficiency in the MSTD process. The apparent viscosity of sludge could be modeled as functions of mixed liquor suspended solids and shear rates. The sludge in the MSTD process showed both shear-thinning and viscoplastic behaviour, and under various shear rates different rheological models could be chosen to predict their flow behaviour. It was also found that sludge concentration and viscosity had significant correlations with membrane fouling in the MSTD process.

Purification of total DNA extracted from activated sludge

Purification of the total DNA extracted from activated sludge samples was studied. The effects of extraction buffers and lysis treatments （lysozyme, sodium dodecyl sulfate （SDS）, sonication, mechanical mill and thermal shock） on yield and purity of the total DNA extracted from activated sludge were investigated. It was found that SDS and mechanical mill were the most effective ways for cell lysis, and both gave the highest DNA yields, while by SDS and thermal shock, the purest DNA extract could be obtained. The combination of SDS with other lysis treatment, such as sonication and thermal shock, could apparently increase the DNA yields but also result in severe shearing. For the purification of the crude DNA extract, polyvinyl polypyrrolidone was used for the removal of humic contaminants. Cetyltrimethyl ammonium bromide, potassium acetate and phenol/chloroform were used to remove proteins and polysaccharides from crude DNA. Crude DNA was further purified by isopropanol precipitation. Thus, a suitable protocol was proposed for DNA extraction, yielding about 49.9 mg （total DNA）/g volatile suspended solids, and the DNA extracts were successfully used in PCR amplifications for 16S rDNA and 16S rDNA V3 region. The PCR products of 16S rDNA V3 region allowed the DGGE analysis （denatured gradient gel electrophoresis） to be possible.

Characteristics of microfauna and their relationships with the performance of an activated sludge plant in China

The occurrence and abundance of the microfauna groups were compared with the physico-chemical and operational parameters of the Baoding Lugang Sewage Treatment Plant in China. Attached and crawling ciliates were the dominant groups of ciliates. Crawling ciliates and testate amoebae showed a strong association with effluent BOD5 （biochemical oxygen demand）. Therefore, these two groups are likely to be useful bioindicators since their number decreased as the process produced poor quality effluent. Testate amoebae also had significant negative correlations with effluent TN （total nitrogen）, NH4^＋-N, SS （suspended solids） and SVI （sludge volumetric index）, which means that this group of ciliates may be indicators of good performance of the activated sludge system. Carnivorous ciliates and flagellates had significant positive correlations with SVI, suggesting that these two groups may be indicators of bad settlement conditions of sludge. As identification of the microfauna species is difficult and time-consuming, we recommend using microfauna functional groups to evaluate the performance of the activated sludge system.

The Role of Diatomite Particles in the Activated Sludge System for Treating Coal Gasification Wastewater

Diatomite is a kind of natural low-cost mineral material. It has a number of unique physical properties and has been widely used as an adsorbent in wastewater treatment. This study was conducted to investigate the aerobic biodegradation of coal gasification wastewater with and without diatomite addition. Experimental results indicated that diatomite added in the activated sludge system could promote the biomass and also enhance the performance of the sludge settling. The average mixed-liquor volatile suspended solids （MLVSS） is increased from 4055 mg.L^-1 to 4518 mg.L^-1 and the average settling volume （SV） are changed only from 45.9% to 47.1%. Diatomite additive could enhance the efficiency of chemical oxygen demand （COD） and total phenols removal from the wastewater. The COD removal increased from 73.3% to near 80% and the total phenols removal increased from 81.4% to 85.8%. The mechanisms of the increase of biomass and pollutants removal may correlates to the improvement of bioavailability and sludge settlement characteristics by diatomite added. Micrograph of the sludge in the diatomite-activated sludge system indicated that the diatomite added could be the carrier of the microbe and also affect the biomass and pollutant removal.