Crystallization management of CsPbI_(2)Br perovskites by PbAc_(2)-incorporated twice spin-coating process for efficient and stable CsPbI_(2)Br perovskite solar cells

CsPbI_(2)Br perovskite solar cell has been extensively studied due to its exceptional thermal stability and relatively stable perovskite phase structure.However,the presence of bromine leads to a rapid crystallization rate of CsPbI_(2)Br films,resulting in small grain size and high defect density.Additionally,CsPbI_(2)Br demonstrates poor light absorption due to its wide bandgap.Therefore,it is crucial to control the crystallization rate and increase the film thickness to reduce defect density,enhance light absorption,and improve photovoltaic performance.In this study,we utilized a PbAc_(2)-incorporated twice spincoating(PTS) process to address these issues.Initially,PbAc_(2) was added to the CsPbI_(2)Br precursor solution to form a CsPbI_(2)Br film,which was then coated with the CsPbI_(2)Br precursor solution to produce the PTS film,Ac^(-)can delay the perovskite crystallization,leading to the formation of thicker and denser CsPbI_(2)Br films.Moreover,lone-pair electrons of the oxygen atom provided by Ac^(-)formed coordination bonds with under-coordinated Pb~(2+) ions to fill halogen ion vacancies,thereby reducing the defect density.Ultimately,the PTS CsPbI_(2)Br device achieved a peak power conversion efficiency(PCE) of 16.19% and maintained 96.7% of its initial PCE over 1500 h at room temperature under 25% relative humidity without any encapsulation.

Enhancing performance of low-temperature processed CsPbI2Br all-inorganic perovskite solar cells using polyethylene oxide-modified TiO_(2)

CsPbX_(3)-based(X=I,Br,Cl)inorganic perovskite solar cells(PSCs)prepared by low-temperature process have attracted much attention because of their low cost and excellent thermal stability.However,the high trap state density and serious charge recombination between low-temperature processed TiO_(2)film and inorganic perovskite layer interface seriously restrict the performance of all-inorganic PSCs.Here a thin polyethylene oxide(PEO)layer is employed to modify TiO_(2)film to passivate traps and promote carrier collection.The impacts of PEO layer on microstructure and photoelectric characteristics of TiO_(2)film and related devices are systematically studied.Characterization results suggest that PEO modification can reduce the surface roughness of TiO_(2)film,decrease its average surface potential,and passivate trap states.At optimal conditions,the champion efficiency of CsPbI_(2)Br PSCs with PEO-modified TiO_(2)(PEO-PSCs)has been improved to 11.24%from 9.03%of reference PSCs.Moreover,the hysteresis behavior and charge recombination have been suppressed in PEO-PSCs.

Application of Feature, Event, and Process Methods to Leakage Scenario Development for Offshore CO_(2) Geological Storage

Offshore carbon dioxide(CO_(2)) geological storage(OCGS) represents a significant strategy for addressing climate change by curtailing greenhouse gas emissions. Nonetheless, the risk of CO_(2) leakage poses a substantial concern associated with this technology. This study introduces an innovative approach for establishing OCGS leakage scenarios, involving four pivotal stages, namely, interactive matrix establishment, risk matrix evaluation, cause–effect analysis, and scenario development, which has been implemented in the Pearl River Estuary Basin in China. The initial phase encompassed the establishment of an interaction matrix for OCGS systems based on features, events, and processes. Subsequent risk matrix evaluation and cause–effect analysis identified key system components, specifically CO_(2) injection and faults/features. Building upon this analysis, two leakage risk scenarios were successfully developed, accompanied by the corresponding mitigation measures. In addition, this study introduces the application of scenario development to risk assessment, including scenario numerical simulation and quantitative assessment. Overall, this research positively contributes to the sustainable development and safe operation of OCGS projects and holds potential for further refinement and broader application to diverse geographical environments and project requirements. This comprehensive study provides valuable insights into the establishment of OCGS leakage scenarios and demonstrates their practical application to risk assessment, laying the foundation for promoting the sustainable development and safe operation of ocean CO_(2) geological storage projects while proposing possibilities for future improvements and broader applications to different contexts.

Study on the Interactivity of Controlled and Automatic Information Processing in L2 Reading

L2 reading is not only an important channel for people to obtain information and knowledge,but also the main way for people to learn a foreign language.Reading information processing can be divided into controlled processing and automatic processing.Controlled information processing is a conscious and resource-intensive processing model,while automatic information processing is an unconscious and automatic processing model.This study investigates the characteristics and interactivity of controlled and automatic information processing in L2 reading,and explores the roles of controlled and automatic information processing strategies in improving L2 reading ability.The findings are as follows:(a)controlled and automatic information processing is interactive in L2 reading;and(b)the uses of controlled and automatic information processing strategies are beneficial to the improvement of the reading ability of L2 learners.This study has important theoretical and practical value in improving the efficiency of L2 reading teaching and learning.

Analysis of the Effect and Influencing Factors of Rural Domestic Sewage Treatment Based on A^(2)O-MBBR Integrated Process

[Objectives] This study was conducted to solve the prominent problems in the treatment of domestic sewage in southern rural areas of China. [Methods] An integrated process treatment mode of anaerobic/anoxic/aerobic moving bed biofilm reactor (A 2O-MBBR) was proposed to analyze and study its operating effect and influencing factors. [Results] The A^(2)O-MBBR mode had good COD removal efficiency and nitrogen and phosphorus removal performance, and the water quality index of the effluent met the Class A standard of GB181918-2002. This mode is suitable for treating rural domestic sewage, and has high treatment effects in different operating periods. In spring, the average removal rates of COD, NH_(4)^(+)-N, TN, TP and SS reached (83.53 ± 2.15)%, (89.44 ± 4.97)%, (67.36±18.53)%, (88.22±11.21)% and (91.73±2.25)%, respectively;In the autumn period, the average removal rates of COD, NH_(4)^(+)-N, TN, TP and SS were (83.49±2.64)%, (89.26±9.19)%, (66.05±17.00)%, (87.48±9.68)%, and (91.13±2.35)%. [Conclusions] This study provides theoretical reference and technical support for the popularization and application of A^(2)O-MBBR integrated process.

STUDY ON PREPARATION OF YBa_2Cu_3O_(7-x) ULTRAFINE POWDERS BY SOL-GEL PROCESS

The ultrafine powders of YBa2Cu3O7-x with the size of 100nm were synthesized by Sol-Gel process using cit-rate as complex and ammonium hydroxide to adjust pH of solu-tion. The process of Sol formation and Gel polymerization of YBa2Cu3O7-x in the Sol-Gel synthetic reaction has bee studied. The particle size ,pruity, sintering activity and superconducting properties of YBa2Cu3O7-x prepared by Sol-Gel method are better than by solid state reaction.

Transition of Y_2BaCuO_5 Phase in Powder Melting Processed YBa_2Cu_3O_(7-x) Superconductors

The morphology and the formation of Y2BaCuO5 phase in powder melting processed YBa2Cu3O7-x superconductors were investigated. The experimental results show the heat treatment can not change the shape of Y2BaCuO5 particles in powder melting processed samples. The formation of round Y2BaCuO5 phase is due to relative content of each constitution of precursor powders in powder melting process. For powder melting process, the excessive liquid phase is eliminated, which restrains the preferred growth of Y2BaCuO5 particles.

Influence of Pressure on the Annealing Process of β-Ca_2SiO_4(C_2S) in Portland Cement

Portland cement is the most common type of cement in general use around the world as a basic ingredient of concrete, mortar, stucco, and non-speciality grout. Dicalcium silicate （Ca2SiO4） is the primary constituent of a number of different types of cement. The β-Ca2SiO4 phase is metastable at room temperature and will transform into β-Ca2SiO4 at 663K. In this work, Portland cement is annealed at a temperature of 950K under pressures in the range of 0-5.5 CPa. The high pressure experiments are carried out in an apparatus with six anvil tops. The effect of high pressure on the obtaining nano-size β-Ca2SiO4 （C2S） process is investigated by x-ray diffraction and transmission electron microscopy. Experimental results show that the grain size of the C2S decreases with the increase of pressure. The volume fraction of the C2S phase increases with the pressure as the pressure is below 3 CPa, and then decreases （P 〉 3 GPa）. The nano-effect is very important to the stabilization of β-Ca2SiO4. The mechanism for the effects of the high pressure on the annealing process of the Portland cement is also discussed.

STUDY OF PREPARATION AND PROPERTY OF YBa_2Cu_3O_(7-δ)-Ag_x COMPOSITE SUPERCONDUCTORS PREPARED BY SOL-GEL PROCESS

YBa2Cu3O7-δ-Agx composite superconductors were prepared by hybrid sintering process using YBa2Cu3O7-δ-Agx ultrafine powder and Ag2O finepower, which were prepared by sol-gel process and precipitation process respectively. The effect of the Ag content on superconducting crictical transition temperature of YBa2Cu3O7-δ-Agx was not evident as long as YBa2Cu3O7-δ-Agx can form continuous network. But Ag can increase superconduction crictical current and density of the composite superconductors. The normal state (i.e. non-superconducting state at room temperature) resistivity shows a percolation threshold at 20%-30% Ag, whereas the superconducting net-work shows a percolationthreshold at 70% -80% Ag.

IN-SITU HVEM STUDY ON PHASE TRANSITION OF YBa_2Cu_3O_(7-x) SUPERCONDUCTING COMPOUND IN PROCESS OF HEATING

In-situ HVEM observation on phase transition of the YBa_2Cu_3O_(7-x) superconducting compound in pro- cess of heating was carried out,and high temperature X-ray diffraction analysis in air and X-ray diffraction phase analysis for the sample treated in vacuum condition were made.The results showed that the temperature of phase transition is related to oxygen content in the sample and in general,is 100℃ to 120℃ lower in vacu- um condition than in air.At 320℃ to 350℃ twin bands begin to disappear,and some Cu_2O are formed on the surface of the sample and transit from orthorhombic YBa_2Cu_3O_(7-x) to arthorhombic Y_2BaCuO_5 compound. This transition was completed at about 500℃.Above 900℃,this compound consists of the Y_2BaCuO_5, BaCuO_2,Y_2O_3 and some other minor compounds.No phase transition was observed during cooling the sample.

Influence of forming process on three-dimensional morphology of TiB_2 particles in Al-Ti-B alloys

A series of Al-Ti-B master alloys were prepared by different preparation routes,and the TiB2 particles in the master alloys were extracted and analyzed.It is found that the forming process has significant influence on the three-dimensional morphology of TiB2 particles.Different preparation routes result in different reaction forms,which accounts for the morphology variation of TiB2 particles.When the Al-Ti-B master alloy is prepared using ＂halide salt＂ route,TiB2 particles exhibit hexagonal platelet morphology and are independent with each other.In addition,the reaction temperature almost does not have influence on the morphology of TiB2 particles.However,TiB2 particles exhibit different morphologies at different reaction temperatures when the master alloys are prepared with Al-3B and Ti sponge.When the master alloy is prepared at 850 ℃,a kind of TiB2 particle agglomeration forms with a size larger than 5 μm.The TiB2 particles change to layered stacking morphology even dendritic morphology with the reaction temperature reaching up to 1200 ℃.

Hot deformation and processing maps of Al_2O_3/Al composites fabricated by flake powder metallurgy

The deformation behaviors of Al2O3/Al composites were investigated by compressive tests conducted at temperature of 300-450 °C and strain rates of 0.001-1.0 s-1 with Gleeble-1500 D thermal simulator system. The results show that the flow stress increases with increasing strain rate and decreasing temperature. The hyperbolic sine constitutive equation can describe the flow stress behavior of Al2O3/Al composites, and the deformation activation energy and constitutive equations were calculated. The processing maps of Al2O3/Al-2 μm and Al2O3/Al-1 μm composites at strain of 0.6 were obtained and the optimum processing domains are in ranges of 300-330 °C, 0.007-0.03 s-1 and 335-360 °C, 0.015-0.06 s-1 for hot working, respectively. The instability zones of flow behavior can also be recognized by the maps.

Dynamic recrystallization of Ti-6Al-2Zr-1Mo-1V in β forging process

The dynamic recrystallization（DRX） behavior of Ti-6Al-2Zr-1Mo-1V alloy was investigated at deformation temperature of 1000-1100 °C and strain rate of 10-3-1.0 s-1 by using compression test.The results show that discontinuous dynamic recrystallization（DDRX） is the predominant recrystallization mechanism at temperature higher than 1050 °C and strain rate lower than 0.01 s-1.Meanwhile,continuous dynamic recrystallization is the main mechanism observed at temperature below 1050 °C and strain rate above 0.01 s-1,mixed with a few DDRX grains.In addition,decreasing strain rate and increasing deformation temperature are found to facilitate the progress of DRX and refinement of grains in the Ti alloy in β forging process.

Changes of the Transcriptional Levels of Molecules Associated with Endogenous Antigen Processing and Presentation in Porcine Skin-derived Dendritic Cells Infected with PCV2 in vivo

[Objective] This study aimed to investigate the changes of the transcriptional levels of molecules associated with endogenous antigen processing and presenta- tion in porcine skin-derived dendritic cells infected with PCV2 in vivo. [Method] Healthy 40-day-old Landrace piglets were infected with porcine circovirus type 2 （PCV2） and euthanized on the 34, 7rd, 14th, 21st and 35th d post inoculation （DPI）. The porcine skin-derived dendritic cells （DCs） were collected to analyze the transcrip- tional levels of molecules （LMP7, UBP, MHC-I, calreticulin） associated with endogenous antigen processing and presentation by using real-time fluorescent quantitative PCR （real-time FQ-PCR）. [Result] The results showed that the level of LMP7 mR- NAs was reduced significantly on the 3DPI （P〈0.05）; the level of UBP mRNAs was consistently up-regulated, which increased significantly on the 21DPI and 35DPI （P〈 0.05）; the level of MHC-I mRNAs was significantly down-regulated on the 7DPI （P〈 0.05）; the level of calreticulin mRNAs was up-regulated slightly without significant dif- ference. [Conclusion] PCV2 can inhibit the endogenous antigen processing and presentation ability of porcine skin-derived DCs at early stages of infection.

焦化废水中几种含氮杂环有机物在A_1-A_2-O系统中的降解特性研究

在对焦化废水中有机物在A1 A2 O生物膜系统中降解转化规律进行分析的基础上 ,选取焦化废水中 6种主要的含氮杂环化合物 :吡啶、吲哚、喹啉、异喹啉、2 甲基喹啉、8 羟基喹啉 ,与苯酚共同配制成溶液 ,在A1 A2 O生物膜系统中运行 ,结果表明上述几种含氮杂环有机物在A1 A2 O系统中都可得到较完全的去除 .它们在厌氧段的降解速率从大到小依次为 :吲哚>2 甲基喹啉 >8 羟基喹啉 >异喹啉 >喹啉 >吡啶 .在厌氧条件下 ,吲哚和喹啉存在拮抗作用 ,而吡啶对喹啉有协同作用 ;

Influence of pretreatment process on structure, morphology and electrochemical properties of Li[Ni_(1/3)Co_(1/3)Mn_(1/3)]O_2 cathode material

The layered Li[Ni1/3Mn1/3Co1/3]O2 was separately synthesized by pretreatment process of ball mill method and solution phase route, using [Ni1/3Co1/3Mn1/3]3O4 and lithium hydroxide as raw materials. The physical and electrochemical behaviors of Li[Ni1/3Mn1/3Co1/3]O2 were characterized by X-ray diffraction （XRD）, scanning electron microscopy （SEM）, field emission scanning electron microscopy （FESEM） and electrochemical charge/discharge cycling tests. The results show that the difference in pretreatment process results in the difference in compound Li[Ni1/3Co1/3Mn1/3]O2 structure, morphology and the electrochemical characteristics. The Li[Ni1/3Mn1/3Co1/3]O2 prepared by solution phase route maintains the uniform spherical morphology of the [Ni1/3Co1/3Mn1/3]3O4, and it exhibits a higher capacity retention and better rate capability than that prepared by ball mill method. The initial discharge capacity of this sample reaches 178 mA-h/g and the capacity retention after 50 cycles is 98.7% at a current density of 20 mA/g. Moreover, it delivers high discharge capacity of 135 mA-h/g at a current density of 1 000 mA/g.

La_2O_3-Mo阴极碳化工艺研究

研究了碳化温度、碳化时间、碳化时苯的浓度对La2O3-Mo阴极碳化度大小和碳化层组织的影响.实验结果表明:在1683～1723K,苯的浓度为8.0～8.5Pa,碳化6～8min后La2O3-Mo阴极碳化度>5%,达到使用要求,碳化层是我们所希望的疏松多孔的Mo2C组织.

改良型A_2/O工艺处理印染废水的研究

阐述了南闸综合污水处理厂废水处理工艺的改良过程,经厌氧+缺氧/好氧+絮凝沉淀+转盘滤池工艺改良后,不仅使出水水质稳定,而且达到了《城镇污水处理厂污染物排放标准》GB18918-2002的一级A标准。

A_1-A_2/O工艺结合生物流化床降解焦化废水NH_3-N、COD中试研究

本文介绍了用 A1 - A2 / O工艺结合流化床技术对攀钢高浓度焦化废水进行 NH3 - N、COD降解的中试试验。试验结果表明 :当进水 NH3 - N<5 0 0 mg/ L、COD<2 0 0 0 m g/ L 时 ,该工艺可以实现 NH3 - N去除率 97%以上 ,COD去除率 85 %以上 ,酚去除率 99.9%。药剂及动力费用为 6 .6元 / t水 ,停留时间 5 0

不同矿浆温度下Ca^(2+)、Mg^(2+)对黄铁矿可浮性的影响

这是一篇矿物加工工程领域的论文。通过单矿物浮选实验、浮选溶液化学、Zeta电位、XPS,研究了不同矿浆温度下Ca^(2+)、Mg^(2+)对黄铁矿浮选效果的影响机理,结果表明:低温能够明显抑制黄铁矿的浮选,且温度降低能够明显弱化Ca^(2+)、Mg^(2+)对黄铁矿浮选的抑制作用。当矿浆温度从20℃降至5℃时,矿浆中带电粒子运动速度减慢,Zeta电位增大,生成氢氧化钙镁沉淀的临界pH值增大,纯水矿浆中黄铁矿表面的FeO/OH的比例减小,Ca^(2+)、Mg^(2+)矿浆中黄铁矿表面FeO/OH含量的降低幅度减小,减少了黄铁矿表面的氧化程度和活性吸附位点,减少了Ca^(2+)、Ca(OH)+,Mg^(2+)和Mg(OH)+等离子在黄铁矿表面的吸附;但低温并不改变Ca^(2+)、Mg^(2+)在黄铁矿表面的存在形式和吸附状态,pH值为9时,钙镁均以Ca^(2+)、Ca(OH)+、Mg^(2+)、Mg(OH)+的形式存在并吸附在黄铁矿表面。