Friction stir processing of AA6061-T4 alloy with SiC particles was successfully carried out.SiC particles were uniformly dispersed into an AA6061-T4 matrix.Also SiC particles promoted the grain refinement of the AA606...Friction stir processing of AA6061-T4 alloy with SiC particles was successfully carried out.SiC particles were uniformly dispersed into an AA6061-T4 matrix.Also SiC particles promoted the grain refinement of the AA6061-T4 matrix by FSP.The mean grain size of the stir zone (SZ) with the SiC particles was obviously smaller than that of the stir zone without the SiC particles.The microhardness of the SZ with the SiC particles reached about HV80 due to the grain refinement and the distribution of the SiC particles.展开更多
The friction stir weldabilities of the strain-hardened AA1050-H24 and precipitate-hardened AA6061-T6 aluminum alloys were examined to reveal the effects of material properties on the friction stir welding behavior. Th...The friction stir weldabilities of the strain-hardened AA1050-H24 and precipitate-hardened AA6061-T6 aluminum alloys were examined to reveal the effects of material properties on the friction stir welding behavior. The experimental results are obtlained. (1) For AA1050-H24, the weld can possess smoother surface ripples; there is no elliptical weld nugget in the weld; there is no discernible interface between the stir zone and the thermomechanically affected zone;and the internal defect of the weld looks like a long crack and is located in the lower part of the weld. (2) For AA6061-T6, the weld usually possesses slightly rougher surface ripples; an elliptical weld nugget clearly exists in the weld; there are discernible interfaces among the weld nugget, thermomechanically affected zone and heat affected zone; and the internal defect of the weld is similar to that of the AA1050-H24 weld. (3) The effective range of welding parameters for AA1050-H24 is narrow, while the one for AA6061-T6 is very wide. (4) The maximum tensile strength efficiency of the AA1050-H24 joints is similar to that of the AA6061-T6 joints, i.e. 79% and 77%, respectively.展开更多
Aluminum 6061 alloy metal matrix composites (MMCs) reinforced with four different weight fractions of (Al<sub>2</sub>O<sub>3</sub> + red mud) particles up to 10 wt% were fabricated by a vortex ...Aluminum 6061 alloy metal matrix composites (MMCs) reinforced with four different weight fractions of (Al<sub>2</sub>O<sub>3</sub> + red mud) particles up to 10 wt% were fabricated by a vortex method. The effects of reinforcement content on the mechanical properties of the composites such as hardness and tensile strength were investigated. The density measurements showed that the samples contained little porosity, and the amount of porosity in the composites increased with increasing weight fraction of particles. Scanning electron microscopic observations of the microstructures revealed that the dispersion of the particles was uniform with small clusters at some places and porosity. The results showed that the hardness and the tensile strength of the composites increased with increasing weight fraction of particles.展开更多
基金Project(51775481)supported by the National Natural Science Foundation of ChinaProject(A2016002017)supported by the High-level Talents Program of Heibei Province,China
基金the financial support for this study from the Malaysian Ministry of Higher Education(MOHE) through the Fundamental Research Grant Scheme and Exploratory Research Grant Scheme
基金Project(10038688)supported by the Fundamental R&D Program for Core Technology of Materials Funded by the Ministry of Knowledge Economy,Republic of Korea
文摘Friction stir processing of AA6061-T4 alloy with SiC particles was successfully carried out.SiC particles were uniformly dispersed into an AA6061-T4 matrix.Also SiC particles promoted the grain refinement of the AA6061-T4 matrix by FSP.The mean grain size of the stir zone (SZ) with the SiC particles was obviously smaller than that of the stir zone without the SiC particles.The microhardness of the SZ with the SiC particles reached about HV80 due to the grain refinement and the distribution of the SiC particles.
文摘The friction stir weldabilities of the strain-hardened AA1050-H24 and precipitate-hardened AA6061-T6 aluminum alloys were examined to reveal the effects of material properties on the friction stir welding behavior. The experimental results are obtlained. (1) For AA1050-H24, the weld can possess smoother surface ripples; there is no elliptical weld nugget in the weld; there is no discernible interface between the stir zone and the thermomechanically affected zone;and the internal defect of the weld looks like a long crack and is located in the lower part of the weld. (2) For AA6061-T6, the weld usually possesses slightly rougher surface ripples; an elliptical weld nugget clearly exists in the weld; there are discernible interfaces among the weld nugget, thermomechanically affected zone and heat affected zone; and the internal defect of the weld is similar to that of the AA1050-H24 weld. (3) The effective range of welding parameters for AA1050-H24 is narrow, while the one for AA6061-T6 is very wide. (4) The maximum tensile strength efficiency of the AA1050-H24 joints is similar to that of the AA6061-T6 joints, i.e. 79% and 77%, respectively.
文摘Aluminum 6061 alloy metal matrix composites (MMCs) reinforced with four different weight fractions of (Al<sub>2</sub>O<sub>3</sub> + red mud) particles up to 10 wt% were fabricated by a vortex method. The effects of reinforcement content on the mechanical properties of the composites such as hardness and tensile strength were investigated. The density measurements showed that the samples contained little porosity, and the amount of porosity in the composites increased with increasing weight fraction of particles. Scanning electron microscopic observations of the microstructures revealed that the dispersion of the particles was uniform with small clusters at some places and porosity. The results showed that the hardness and the tensile strength of the composites increased with increasing weight fraction of particles.
