Fuel cell using borohydride as the fuel has received much attention. AB5-type hydrogen storage alloy used as the anodic material instead of noble metals has been investigated. In order to restrain the generation of hy...Fuel cell using borohydride as the fuel has received much attention. AB5-type hydrogen storage alloy used as the anodic material instead of noble metals has been investigated. In order to restrain the generation of hydrogen and enhance the utilization of borohydride, Ti/Zr metal powders has been added into the parent LmNi4.78Mn0.22 （where Lm is La-richened mischmetal） alloy （LNM） by ball milling and heat treatment methods. It is found that the addition of Ti/Zr metal powders lowers the electrochemical catalytic activity of the electrodes, at the same time, restrains the generation of hydrogen and enhances the utilization of the fuel. All the results show that the hydrogen generation rate or the utilization of the fuel is directly relative to the electrochemical catalytic activity or the discharge capability of the electrodes. The utilization of the fuel increases with discharge current density. It is very important to find a balance between the discharge capability and the utilization of the fuel.展开更多
The nonstoichiometric La-rich mischmetal (designated by MI)-based hydrogen storage alloy with a composition of MI(Ni0.64Co0.2Mn0.12Al0.04)(4.76) was prepared by arc melting and annealed at 1173 K for 10 h to investiga...The nonstoichiometric La-rich mischmetal (designated by MI)-based hydrogen storage alloy with a composition of MI(Ni0.64Co0.2Mn0.12Al0.04)(4.76) was prepared by arc melting and annealed at 1173 K for 10 h to investigate the effect of annealing treatment on the microstructure and electrochemical characteristics of the alloy. X-ray diffraction analysis showed that annealing can cause a release of the crystal lattice strain and an increase in amounts of the La2Ni7-type second phase in MI(Ni0.64Co0.20Mn0.12Al0.04)(4.76) alloy. Scanning electron microscopy and electron probe microanalysis examinations indicated that annealing leads to disappearance of the dendrite structure in the as-cast alloy, growth of crystal grain, and decrease of composition segregation. The annealing at 1173 K for 10 h flattened and extended the potential plateau and increased the maximum discharge capacity to 328 mA center dot h/g from 310 mA center dot h/g and the cycling life. The mechanism of the improvement in electrochemical characteristics was discussed based on the alloy microstructure change induced by annealing.展开更多
文摘Fuel cell using borohydride as the fuel has received much attention. AB5-type hydrogen storage alloy used as the anodic material instead of noble metals has been investigated. In order to restrain the generation of hydrogen and enhance the utilization of borohydride, Ti/Zr metal powders has been added into the parent LmNi4.78Mn0.22 （where Lm is La-richened mischmetal） alloy （LNM） by ball milling and heat treatment methods. It is found that the addition of Ti/Zr metal powders lowers the electrochemical catalytic activity of the electrodes, at the same time, restrains the generation of hydrogen and enhances the utilization of the fuel. All the results show that the hydrogen generation rate or the utilization of the fuel is directly relative to the electrochemical catalytic activity or the discharge capability of the electrodes. The utilization of the fuel increases with discharge current density. It is very important to find a balance between the discharge capability and the utilization of the fuel.
文摘The nonstoichiometric La-rich mischmetal (designated by MI)-based hydrogen storage alloy with a composition of MI(Ni0.64Co0.2Mn0.12Al0.04)(4.76) was prepared by arc melting and annealed at 1173 K for 10 h to investigate the effect of annealing treatment on the microstructure and electrochemical characteristics of the alloy. X-ray diffraction analysis showed that annealing can cause a release of the crystal lattice strain and an increase in amounts of the La2Ni7-type second phase in MI(Ni0.64Co0.20Mn0.12Al0.04)(4.76) alloy. Scanning electron microscopy and electron probe microanalysis examinations indicated that annealing leads to disappearance of the dendrite structure in the as-cast alloy, growth of crystal grain, and decrease of composition segregation. The annealing at 1173 K for 10 h flattened and extended the potential plateau and increased the maximum discharge capacity to 328 mA center dot h/g from 310 mA center dot h/g and the cycling life. The mechanism of the improvement in electrochemical characteristics was discussed based on the alloy microstructure change induced by annealing.
