REALIZATION OF FUZZY-FILTER CONTROL ON A BRUSHLESS AC GENERATOR

The transistor voltage regulators have been widely adopted in the brushless AC generators in aircraft. This paper researches the digital voltage regulator. The paper presents the hardware platform of the digital voltage regulator, which is based on a DSP chip — TMS320C32. A novel fuzzy filter control structure is developed from normal fuzzy control strategy. And the fuzzy filter control algorithm is adopted in the hardware platform successfully. The computer simulation has been conducted. Some control parameters have been obtained through the simulation. The same parameters have been applied in the digital regulation experiments on a brushless AC generator. In the experiment, the digital voltage regulator results in good responses. From the experiment results, it can be seen that the new control algorithm is efficient for the digital voltage regulator.

MODEL AND SIMULATION FOR A BRUSHLESS AC GENERATOR WITH A ROTARY RECTIFIER

Objective For a brushless AC generator with a rotary rectifier, it is necessary and significant to model and simulate at normal and fault operation states. Methods Two new concepts, namely, Simulink signals and PSB(Power System Blockset) variables, are proposed, and the difference between the two concepts is clarified. Based on the new model for synchronous machines \, a simulation model for a brushless AC generator with a rotary rectifier is constructed by Matlab/Simulink/PSB. This new model, which has a speed input terminal and an exciting voltage input one, can simulate the real electrical characters and direct mechanical connection between two synchronous machines perfectly. The rotary rectifier is a three-phase full-wave bridge rectifier which consists of six diodes. The model for the diodes is a macro-model which possesses much better accuracy than an ideal one of switches. Results Based on the present model, some simulation results such as exciting current waveform, phase current waveform and phase voltbge waveform are afftained at several operation conditions. Conclusion The simulation for a brushless AC generator with a rotary rectifier is demonstrated at normal and fault operation states, respectively. The results confirm the presented method.

Overview and Development of Variable Frequency AC Generators for More Electric Aircraft Generation System

With the development of more electric aircraft(MEA),higher demands for electrical energy are put forward in generation systems.Compared to constant frequency AC(CFAC)generation systems,the constant speed drive(CSD)is eliminated and integrated starter/generator(SG)can be realized in variable frequency AC(VFAC)generation systems.In this paper,an overview of VFAC generators for safety-critical aircraft applications is presented,with a particular focus on the key features and requirements of candidate generators and the starting control strategies.Wound rotor synchronous machines(WRSMs)are typical generators used in VFAC generation systems so far.Meanwhile,hybrid excitation synchronous machines(HESMs)and cage-type induction machines are promising candidates for VFAC generation systems.The generation operation of WRSM is relatively mature,however,the SG technology of WRSM is still full of challenges.As one of the most important issues,the starting excitation methods of WRSM are summarized.An HESM-based VFAC SG system is proposed and developed in this paper.The experimental results show that the starting mode,transition mode and generating mode of the VFAC SG system are realized.The continuous progress of VFAC generation system makes great contributions to the realization of MEA.

Influence of Temperature Probes Installation on the Salient Pole to Temperature Measurement

Accurate and reliable information about the temperature of the synchronous generators excitation winding hot spot is necessary to determine the dynamic limit caused by excitation winding overheating in the PQ diagram. For good estimation of a position and the hot spot temperature it is decided to mount 19 temperature probes on one pole of the 6-pole, 400 kVA. 50 llz synchronous generator. Due to a large number of the probes and because the probes should be glued with the metal epoxy it was assumed that mounting of the probes will disrupt the temperature field of the excitation winding. To get the answer to this question the excitation winding resistance was measured betbre and after mounting the probes, in a hot and a cold state. Temperature rise can be estimated if the resistance ratio in the hot and the cold state is known. The paper also addresses the analysis of the measurement accuracy. The result shows that, there is no significant influence on the temperature when mounting the 19 temperature probes which covered 10% of the pole excitation winding surface.