Reliability of DC-link capacitor in pulsed power supply for accelerator magnet

Capacitors are widely used in pulsed magnet power supplies to reduce ripple voltage,store energy,and decrease power variation.In this study,DC-link capacitors in pulsed power supplies were investigated.By deriving an analytical method for the capacitor current on the H-bridge topology side,the root-mean-square value of the capacitor current was calculated,which helps in selecting the DC-link capacitors.The proposed method solves this problem quickly and with high accuracy.The current reconstruction of the DC-link capacitor is proposed to avoid structural damage in the capacitor’s current measurement,and the capacitor’s hotspot temperature and temperature rise are calculated using the FFT transform.The test results showed that the error between the calculated and measured temperature increases was within 1.5℃.Finally,the lifetime of DC-link capacitors was predicted based on Monte Carlo analysis.The proposed method can evaluate the reliability of DC-link capacitors in a non-isolated switching pulsed power supply for accelerators and is also applicable to film capacitors.

单级三相谐波电流注入可升降压AC/DC变换器

为适应电动车充电电压宽范围变化需求,本文针对传统充电桩前级整流器拓扑开展研究,提出一种新式单级三相AC/DC变换器。该变换器集成了三相桥式不控整流电路与Cuk模块,为降低输入侧电流谐波分量,选用双向开关管构建谐波电流回馈通路,整体构造成单级式拓扑结构。文章阐述了变换器的电路结构及工作模态,通过建立变换器的等效模型推导出电压增益。变换器通过简单的控制逻辑即可实现正弦输入电流并拥有高功率因数。最后通过搭建变换器数字控制实验平台验证了所提变换器的可行性。

高频链AC-DC矩阵变换器的变控制频率软开关调制策略

针对高频链AC-DC矩阵变换器的高效率要求,提出了一种变控制频率软开关调制策略。该调制策略在基于零矢量嵌入的分段同步控制策略基础上,以单控制周期平均功率不变为原则,通过改变控制周期长度,并调整一个控制周期内的电压矢量排布,优化脉冲宽度,使变换器在换流时全部开关器件的零电压开通成为可能。通过仿真分析和实验证明,采用本文提出的变控制频率调制策略,变换器在整流和逆变模式下,均可实现网侧电流三相平衡正弦,功率因数达到0.981,输出电压纹波小,最高效率达到96.9%,实现了高性能、高效率运行。

基于双模式变频移相调制的单级式双有源桥型DC-AC变换器

针对单级式双有源桥(DAB)型DC-AC变换器关断电流较大和软开关范围有限的问题,该文提出一种双模式变频移相调制策略。首先,对DAB变换器的单移相(SPS)调制和扩展移相(EPS)调制进行时域分析,得到其功率传输特性;然后,分析变换器的关断电流与软开关条件,得到移相比和开关频率约束方程;在此基础上,分析双模式间的移相比边界条件,提出变换器运行模式的切换机制,从而在实现变换器单级功率变换的同时,保证全范围软开关并降低低压侧的关断电流;最后,通过仿真和实验验证了所提调制策略的有效性与可行性。

不平衡电网下AC-DC矩阵变换器的新型模型预测控制

为降低AC-DC矩阵变换器在输入不平衡条件下网侧有功功率波动,以及离散型模型预测控制中开关频率不固定的问题,提出一种新型模型预测控制方法。通过根据电网电流相位角选择有效矢量,避免了传统模型预测控制评估价值函数计算的负担。提出了一种二阶扩展复数卡尔曼滤波器,计算精度可以达到泰勒级数展开的二阶项,新型模型预测控制能够在不平衡电网系统中应用。仿真结果表明:所提控制策略在输入电压不平衡工况下,能够有效抑制网侧电流谐波,稳定系统输出的有功功率,并且表现出良好的性能。

AC/DC变换器传导EMI建模与仿真

本研究旨在探究AC/DC变换器传导EMI的建模与仿真,强调其在电力电子系统设计中的重要性。通过基于传导机制的EMI建模方法,本研究完成了对AC/DC变换器传导EMI的仿真与分析。得出的基本结论是传导EMI在AC/DC变换器中具有显著影响,为其设计与优化提供了新的视角。此研究为电力电子系统的EMI管理提供了重要参考,有助于提高系统性能与可靠性。

基于电流应力优化和6脉波调制的双有源桥AC/DC变换器控制策略

针对双有源桥(dual active bridges,简称DAB)AC/DC变换器,该文提出基于电流应力优化和6脉波调制的双有源桥AC/DC变换器控制策略.DAB和三相逆变器(three phase inverter,简称TPI)是双有源桥AC/DC变换器的两个关键单元.对DAB采用电流应力优化,对TPI采用6脉波调制.仿真实验结果表明:相对于单移相(single phase shift,简称SPS)调制策略,该文策略的电感电流的峰值更小,即能更有效地降低电流应力.因此,该文所提策略具有优越性.

AC/DC通信电源模块远场电磁辐射发射预测研究

AC/DC通信电源产生的电磁辐射易超过限值,对其电磁辐射机理和预测方法开展研究有助于改善电磁兼容性设计。首先,在分析AC/DC通信电源模块共模电磁噪声的形成源头和传播路径后,提出其远场电磁辐射可分解为由“输入端口”、“输出端口”共模电压驱动的2类辐射。然后,提出将共模电压驱动源与寄生辐射体的辐射传递函数相结合,进行远场电磁辐射预测的新方法;设计频谱分析仪+电阻衰减器,实现各共模电压驱动源的频谱测量;采用FEKO电磁仿真软件,通过数值计算得到各寄生辐射体的辐射传递函数。最后,实现了4 kW AC/DC通信电源模块辐射预测,并实测验证了其有效性。

隔离型双向AC-DC矩阵变换器闭环控制方法研究

根据隔离型双向AC-DC矩阵变换器(Isolated AC-DC Matrix Converter,IAMC)没有中间电容缓冲环节,输入和输出变换器控制之间存在耦合,研究提出了IAMC两级功率变换器的控制方法。通过对全桥变换器进行闭环控制进而实现对直流侧输出电流和功率的直接控制;三相-单相矩阵变换器实现对有功和无功功率的独立控制,以满足网侧功率因数的高精度控制。所提控制策略有效降低了两级变换器的耦合强度,保证了系统的良好性能。在MATLAB中进行仿真,结果表明,所提出的控制方法在使系统电能质量得到提高的同时,可以实现单位功率因数可调,验证了所提控制策略的正确性和有效性。

Research on power electronic transformer applied in AC/DC hybrid distribution networks

The AC/DC hybrid distribution network is one of the trends in distribution network development, which poses great challenges to the traditional distribution transformer. In this paper, a new topology suitable for AC/DC hybrid distribution network is put forward according to the demands of power grid, with advantages of accepting DG and DC loads, while clearing DC fault by blocking the clamping double sub-module(CDSM) of input stage. Then, this paper shows the typical structure of AC/DC distribution network that is hand in hand. Based on the new topology, this paper designs the control and modulation strategies of each stage, where the outer loop controller of input stage is emphasized for its twocontrol mode. At last, the rationality of new topology and the validity of control strategies are verified by the steady and dynamic state simulation. At the same time, the simulation results highlight the role of PET in energy regulation.

基于标准特征多项式的变电站光储直柔系统双向AC/DC变换器控制策略

为增强变电站光储直柔系统的可靠性,针对其在并网过程中会对变电站电能质量造成不良影响,以及现有设计方法难于工程化问题提出了一种面向工程化的基于标准特征多项式配置方法(SCP)的双向AC/DC变换器控制策略。通过建立变电站光储直柔(PEDF)系统变换器的数学模型,并分析控制器参数对变换器在不同运行模式下的电能质量的影响,然后采用SCP方法来配置闭环系统特征值,分析该方法对抑制并网电流谐波、改善AC/DC变换器并网电能质量的作用,最后对此进行仿真分析并和传统PI控制器效果进行比较,结果表明:所提策略降低了AC/DC变换器在谐波畸变率和并网电流不对称度,系统设计简便,且具有很好地鲁棒性,适合工程实践。

A new high-performance AC/DC power factor correction switching converter based on one-cycle control technology and active floating-charge technology

A new family of converters,high-performance AC/DC power factor correction(PFC) switching converters with one-cycle control technology and active floating-charge technology,was derived and experimentally verified.The topology of a single-phase CCM and DCM Boost-PFC switching converter was also analyzed.Its operating prniciples and control methods were expounded.Based on these,a new type of AC/DC switching converter circuits for PFC combined with one-cycle control technology was presented herein.The proposed AC/DC switching converter significantly helps improve the converter efficiency and its power factor value.

Fabricating AC/DC nanogenerators based on single ZnO nanowires by using a nanomanipulator in a scanning electron microscope

Single zinc oxide nanowires(ZnO NWs)are promising for nanogenerators because of their excellent semiconducting and piezoelectric properties,but characterizing the latter efficiently is challenging.As reported here,an electrical breakdown strategy was used to construct single ZnO NWs with a specific length.With the high operability of a nanomanipulator in a scanning electron microscope,ZnO-NW-based twoprobe and three-probe structures were constructed for fabricating AC/DC nanogenerators,respectively.For a ZnO NW,an AC output of between−15.31 mV and 5.82 mV was achieved,while for a DC nanogenerator,an output of24.3 mV was realized.Also,the three-probe structure’s output method was changed to verify the distribution of piezoelectric charges when a single ZnO NW is bent by a probe,and DC outputs of different amplitudes were achieved.This study provides a low-cost,highly convenient,and operational method for studying the AC/DC output characteristics of single NWs,which is beneficial for the further development of nanogenerators.

Flexible linear clock-based distributed self-triggered active power-sharing secondary control of AC microgrids

Traditional active power sharing in microgrids,achieved by the distributed average consensus,requires each controller to continuously trigger and communicate with each other,which is a wasteful use of the limited computation and communication resources of the secondary controller.To enhance the efficiency of secondary control,we developed a novel distributed self-triggered active power-sharing control strategy by introducing the signum function and a flexible linear clock.Unlike continuous communication–based controllers,the proposed self-triggered distributed controller prompts distributed generators to perform control actions and share information with their neighbors only at specific time instants monitored by the linear clock.Therefore,this approach results in a significant reduction in both the computation and communication requirements.Moreover,this design naturally avoids Zeno behavior.Furthermore,a modified triggering condition was established to achieve further reductions in computation and communication.The simulation results confirmed that the proposed control scheme achieves distributed active power sharing with very few controller triggers,thereby substantially enhancing the efficacy of secondary control in MGs.

DC microgrid stability control with constant power load:a review

The DC microgrid has the advantages of high energy conversion efficiency,high energy transmission density,no reactive power flow,and grid-connected synchronization.It is an essential component of the future intelligent power distribution system.Constant power load(CPL)will degrade the stability of the DC microgrid and cause system voltage oscillation due to its negative resistance characteristics.As a result,the stability of DC microgrids with CPL has become a problem.At present,the research on the stability of DC microgrid is mainly focused on unipolar DC microgrid,while the research on bipolar DC microgrid lacks systematic discussion.The stability of DC microgrid using CPL was studied first,and then the current stability criteria of DC microgrid were summarized,and its research trend was analyzed.On this basis,aiming at the stability problem caused by CPL,the existing control methods were summarized from the perspective of source converter output impedance and load converter input impedance,and the current control methods were outlined as active and passive control methods.Lastly,the research path of bipolar DC microgrid stability with CPL was prospected.

V2G车网互联的双向AC/DC变换器直流阻抗模型及特性分析

双向AC/DC变换器的控制及直流输出阻抗是电动汽车充电桩并网运行及稳定性分析的关键。首先,提出含直流下垂环节的虚拟同步电机(VSM)控制策略,并利用上层功率指令实现双向AC/DC变换器直流电压的无差调节。然后,建立VSM功率控制环小信号模型,分析有功功率传输、有功功率指令与直流电压间的交互作用及影响。接着,建立双向AC/DC变换器在直流下垂VSM控制策略下的直流输出阻抗模型,详细分析阻尼系数、惯性系数、直流侧电容、传输功率、直流下垂系数等关键参数对直流输出阻抗的影响。最后,通过仿真及阻抗测量验证了所提直流下垂VSM控制策略的有效性和阻抗模型的正确性。

基于单片机的AC-DC变换电路设计

传统的AC-DC变换电路由于要通过高频变压器来实现电压变换,存在效率较低、电源的波纹很难降低等问题。因此,设计一种以单片机为核心控制器件的新型单相AC-DC变换电路。单相AC-DC变换电路设计结合BOOST开关器、输入负反馈和脉冲宽度调制,采用单片机辅助控制相结合的方式实现闭环控制,保证输出的稳定和高效。该电路包括全波桥式整流电路、BOOST开关器、电压反馈电路、电流采样电路和功率因数测量电路,通过负反馈控制UC3845芯片来改变PWM控制信号,从而调整BOOST开关器开关的通断,使输出电压稳定在36 V。单相AC-DC变换电路具有PFC功能,可通过LCD将实时的PF值进行检测,显示输出电流、输出电压、功率因数等数据。另外,在输出端设计了过流保护报警功能,该设计选取STC51单片机系列中的89C52RC芯片作为控制核心,结合电流电压检测共同来实现。实验结果表明,实测负载调整率为0.28%,电压调整率为0.28%,功率因数为0.91,说明所设计电路优于传统的AC-DC变换电路,具有转换率高的特点。

高效单片AC/DC电源管理集成电路设计

随着科技快速发展,电子产品的复杂程度不断升级,日益向小型化、智能化、高效能方向迈进。电源管理系统作为电子产品中的重要系统之一,其重要作用逐渐凸显。本研究设计了一种单片AC/DC开关电源集成电路,该电路具有效率高、体积小、可靠性高等优点。因此,本文基于高效的单片AC/DC电源管理集成电路构成,对其进行了优化设计,希望能够为我国电源管理系统设计行业的相关工作提供参考和借鉴。

Performance of PSS to Damp Power Oscillations Caused by an HVDC Link in AC-DC Power System

HVDC (High Voltage Direct Current) systems are increasingly being applied to improve power system operation and controllability. However, inappropriate setting of HVDC controller may have a detriment effect on the system performance. Generally, PSS (Power System Stabilizer) is known as a simple concept, easy to perform, and computationally effective to enhance damping of power system oscillations through excitation control of synchronous generator. This paper examines the effectiveness of the PSS to enhance the dynamic performance of AC-DC power systems and to compensate the negative damping of HVDC system. The dynamic performance is evaluated by examining the system response to various disturbances. In order to ensure the reliability of the simulation test results as well as the performance of the PSS, detailed HVDC modeling is adopted using SimPowerSystems toolbox in the MATLAB, and some important conclusions are drawn.

Investigation on some key problems of large power AC-DC-AC converter

China is an important country in iron and steel industry.Power electronics converters are widely used.For the cold rolling mills of high speed,AC-DC-AC converters should be used.In the paper,the design and the control system of the large power three-level AC - DC - AC converter with IGCTs is investigated,and a back-to-back large power three-level AC - DC - AC converter with IGCTs has been got. With a series experiments,the performance of the converter is examined.The experiment result indicates the converter reaches the design requirement and it shows excellent performance.The converter system has been put into use safely.It is estimated that the AC - DC - AC converter system will be used in the drive systems for rolling mills in the near future.