MoSi2 samples were prepared by a self-propagating high-temperature synthesis (SHS) and a hot-press technique. The sliding friction and wear properties of intermetallic MoSi2 against AISI10045 steel under dry friction ...MoSi2 samples were prepared by a self-propagating high-temperature synthesis (SHS) and a hot-press technique. The sliding friction and wear properties of intermetallic MoSi2 against AISI10045 steel under dry friction and oil lubrication conditions were investigated with a MRH-5A type ring-on-block friction and wear tester. The elemental composition, microstructure and worn surface morphology of the MoSi2 material were observed and analyzed by means of scanning electron microscopy (SEM) and X-ray diffraction (XRD). The synthetic parameter pv value reflecting friction work, was used to discuss the tribological properties of MoSi2 material. The results show that 1) oil lubrication can obviously improve the tribological properties of MoSi2, 2) the bigger the pv value, the greater the antifriction and the abrasive resistance of MoSi2 under oil lubrication, 3) with an increase in the pv value, the wear mechanism of MoSi2 material under dry sliding friction is the fatigue fracture and adhesive wear and 4) under oil lubrication the wear mechanism is mainly fatigue pitting.展开更多
莱钢特钢事业部新区采用铁水+废钢-100 t电弧炉-LF-VD-Φ500,600 mm圆坯连铸-步进式加热炉-950轧机轧制-缓冷-退火的流程生产Φ110～260 mm AISI4145HM钢(/%:0.44～0.46C,0.21～0.23Si,1.32～1.33Mn,1.18～1.20Cr,0.30～0.31Mo,0.16～0....莱钢特钢事业部新区采用铁水+废钢-100 t电弧炉-LF-VD-Φ500,600 mm圆坯连铸-步进式加热炉-950轧机轧制-缓冷-退火的流程生产Φ110～260 mm AISI4145HM钢(/%:0.44～0.46C,0.21～0.23Si,1.32～1.33Mn,1.18～1.20Cr,0.30～0.31Mo,0.16～0.17Ni,≤0.012P,≤0.004S,≤0.05Cu,0.15～0.35Alt)。通过控制电弧炉终点[C]≥0.15%,[P]≤0.008%,出钢预脱氧和合金化,LF高铝精炼渣(30%～40%Al_2O_3)及喂0.45kg/t_钢钙线,VD后梯度软吹,控制中间包钢水过热度12～25℃,拉速0.25～0.35 m/min,全程保护浇铸及M-EMS和F-EMS,轧后缓冷、退火等工艺措施,生产的铸坯低倍组织良好,中心疏松和中心缩孔≤1.0级,裂纹和皮下气泡为0级,各类夹杂物级别≤1.5,级别总和≤7.0,钢的各项指标均满足协议要求。展开更多
基金Projects 50405041 supported by National Natural Science Foundation of China and 04C218 by Hunan Province Education Foundation of China
文摘MoSi2 samples were prepared by a self-propagating high-temperature synthesis (SHS) and a hot-press technique. The sliding friction and wear properties of intermetallic MoSi2 against AISI10045 steel under dry friction and oil lubrication conditions were investigated with a MRH-5A type ring-on-block friction and wear tester. The elemental composition, microstructure and worn surface morphology of the MoSi2 material were observed and analyzed by means of scanning electron microscopy (SEM) and X-ray diffraction (XRD). The synthetic parameter pv value reflecting friction work, was used to discuss the tribological properties of MoSi2 material. The results show that 1) oil lubrication can obviously improve the tribological properties of MoSi2, 2) the bigger the pv value, the greater the antifriction and the abrasive resistance of MoSi2 under oil lubrication, 3) with an increase in the pv value, the wear mechanism of MoSi2 material under dry sliding friction is the fatigue fracture and adhesive wear and 4) under oil lubrication the wear mechanism is mainly fatigue pitting.
