Effect of finish-rolling conditions on mechanical properties and texture characteristics of AM50 alloy sheet

The conventional hot rolling of AM50 alloy at different roll temperatures and speeds was performed to investigate the effects of finish-rolling conditions on the mechanical properties and texture of rolled sheet. The better combination between strength（ultimate tensile strength： 295 MPa; yield strength： 224 MPa） and ductility（22.9%） can be obtained for the AM50 sheet rolled at the roll temperature of 200 °C with the roll speed of 5 m/min. The yield stress depends strongly on roll temperature, while the texture intensity in rolled sheets is more sensitive to roll speed during hot rolling. Increasing rolling temperature or roll speed can improve the mechanical anisotropy of AM50 rolled sheets.

Poly caprolactone/titanium dioxide nanofiber coating on AM50 alloy for biomedical application

Poly caprolactone(PCL)and Poly caprolactone/TiO_(2)(PCL/TiO_(2))composite nanofiber with different weight percentage compositions(2 wt%,4 wt%and 6 wt%)of TiO_(2)were prepared and coated over AM50 alloy using electrospinning technique.The surface morphology and elemental composition result confirms that the PCL/TiO_(2)composite nanofiber fiber were successfully electrospun on the surface of AM50 alloy.The degradation behavior of PCL and PCL/6 wt%TiO_(2)coated AM50 alloy was studied by immersing in Simulated Body Fluid(SBF)solution.The electrochemical and cell proliferation studies reveals that the cellular behavior of PCL and PCL/6 wt%TiO_(2)composite nanofiber exhibited good support for cell proliferation with enhanced corrosion resistance of AM50 alloy in SBF solution.

Effect of low concentration electrolytes on the formation and corrosion resistance of PEO coatings on AM50 magnesium alloy

In this paper,the formation process,morphology,and electrochemical performance of PEO coatings on AM50 magnesium alloy prepared in low concentration phosphate,aluminate,and phosphate-aluminate electrolytes were systematically studied.The results show that the coatings prepared from the phosphate electrolytes have a higher thickness and better corrosion resistance properties compared to the other electrolytes.The coatings prepared from low concentration phosphate-aluminate mixed electrolytes have slightly thinner thickness,a similar coating structure and an order of magnitude lower value of electrochemical impedance compared with phosphate electrolyte coatings.The Coatings prepared from low concentration aluminate electrolytes have the lowest thickness and the worst corrosion resistance properties which gets close to corrosion behavior of the bare AM50 under the same test conditions.Considering application,coatings prepared from single low concentration phosphate electrolytes and low concentration phosphate-aluminate electrolytes have greater potential than single low concentration aluminate coatings.However,reducing the electrolyte concentrations of coating forming ions too much has negative influence on the coating growth rate.

Effect of process parameters on microstructure and properties of AM50A magnesium alloy parts formed by double control forming

Effects of process parameters on microstructure and mechanical properties of the AM50A magnesium alloy components formed by double control forming （DCF） were investigated via a four-factor and four-level orthogonal experiment. The variable curves of DCF showed that the forging procedure was started in the following 35 ms after the injection procedure was completed. It was confirmed that the high-speed filling and high-pressure densifying were combined together in the DCF process. Better surface quality and higher mechanical properties were achieved in the components formed by DCF as compared to die casting （DC） due to the refined and uniform microstructure with a few defects or without defects. Injection speed affected more effectively the yield strength （YS）, ultimate tensile strength （UTS） and elongation as compared to pouring temperature, die temperature and forging force. But the pouring temperature had a more significant effect on hardness as compared to injection speed, die temperature and forging force. Pouring temperature of 675 ＆#176;C, injection speed of 2.7 m/s and forging force of 4000 kN except for die temperature were the optimal parameters for obtaining the highest YS, UTS, elongation and Vickers hardness. Die temperatures of 205, 195, 195 and 225 ＆#176;C were involved in achieving the highest YS, UTS, elongation and Vickers hardness, respectively. Obvious microporosity and microcracks were found on the fracture surface of the components formed by DC, deteriorating the mechanical properties. However, the tensile fracture morphology of the components formed by DCF was characterized by ductile fracture due to a large number of dimples and no defects, which was beneficial for improving the mechanical properties.

Influence of Ce addition on microstructure and mechanical properties of high pressure die cast AM50 magnesium alloy

The influence of Ce addition on the microstructure and mechanical properties of AM50 magnesium alloy was investigated to improve its mechanical properties.The results show that the addition of Ce to AM50 alloy results in the grain refinement and the mechanical properties of the Ce-modified AM50 at room and elevated temperatures are remarkably improved.AM50 magnesium alloy containing 1% Ce（mass fraction） shows better refinement and mechanical properties compared with the AM50 magnesium alloy with 0.5% Ce and even AM50 alloy without any Ce.

Effects of aging on the microstructures and mechanical properties of extruded AM50+xCa magnesium alloys

The effects of aging treatment on the microstructures and mechanical properties of extruded AM50 ＋ xCa alloys （x=0, 1, 2 wt.%） were studied. The results indicated the secondary phase Mgl7Al12 precipitated from the saturated α-Mg solid solution while Al2Ca changed slightly when the aging time was increased. The hardness of extruded AM50 ＋ xCa al- loys increased initially to its peak, and then dropped to reach its original hardness with the increase in aging time. With the increase in aging temperature, the hardness of the AM50 ＋ 2Ca ahoy decreased, whereas the hardness of AM50 and AM50 ＋ 1Ca alloys decreased in the initial stages of aging treatment and increased in the later stages of aging treatment. The tensile strengths of AM50 and AM50 ＋ 1Ca alloys increased after aging treatment for the precipitation of Mg17Al12 phase, which increases the resistance against dislocation movement at the grain boundary; with increase in aging temperature, their tensile strengths increased. For AM50 ＋ 2Ca alloy, the tensile strength declined after aging at 150℃ and 175℃, while it increased slightly at 200℃. The ductility of AM50 ＋ xCa alloys （x = 0, 1, 2 wt.%） declined after aging treatment.

Microstructure and tensile properties of AM50A magnesium alloy prepared by recrystallisation and partial melting process

Prior to thixoextrusion, the microstructural evolution of semi-solid AM50A magnesium alloy prepared by the recrystallisation and partial remelting (RAP) route was investigated.The effect of compressive ratio on microstructure of semi-solid AM50A magnesium alloy was studied.Furthermore, tensile properties of thixoextruded components were determined.The results showed that the occurrence of recrystallised grains was closely associated with the location of the first liquid formed above the solidus.With prolonging holding time, deformed microstructure was penetrated, causing fragmentation, which resulted in the decrease of average grain size.Moreover, prolonging holding time was favorable for the improvement of the degree of spheroidization due to the increase in the amount of liquid.With the increase in compressive ratio, the size of solid grain decreased, the degree of spheroidization was improved during partial remelting, and the tensile properties of thixoextruded AM50A components were improved.The tensile properties for AM50A magnesium alloy thixoextruded from starting material produced by the RAP route were better than those of the same alloy produced by die-casting and thixomolding.

Enhanced strengthening by two-step progressive solution and aging treatment in AM50-4%(Zn,Y) magnesium alloy

AM50-4%(Zn,Y)alloy with a Zn/Y mole ratio of6:1was subjected to thermal analysis,and the results were used for designing a two-step progressive solution treatment process.The effects of solution and aging treatments on the microstructure and mechanical properties of the AM50-4%(Zn,Y)alloy were investigated using OM,XRD,SEM/EDS,TEM,tensile test and hardness test.The experimental results demonstrated that the two-step progressive solution treatment could make theΦandβphases sufficiently dissolve into the matrix which possessed higher supersaturated degree of the dissolved solute compared with the one-step solution treatment.This resulted in a certain enhancement of the precipitation strengthening effect during the subsequent aging process.The precipitation of theФphase had a greater impact on the comprehensive mechanical properties of the alloy thanβphase precipitation when the aging treatment was performed at180℃.The peak aging strength of the AM50-4%(Zn,Y)alloy which was subjected to the two-step progressive solution treatment process(345℃for16h and375℃for6h)was obtained after the aging treatment at180℃for12h.

Low Porosity in Cast Magnesium Welds by Advanced Laser Twin-Spot Welding

Porosity is reported to be a major issue when welding cast magnesium. Therefore, it is important to understand the pore formation mechanisms and find procedures that could be used to reduce porosity. This study investigated the possibility of using twin-spot optics for reducing the porosity in laser welded cast magnesium. Two twin-spot welding setups were compared using either a beam splitter or twin-spot welding with primary and secondary (placed in front of the primary optic) optics. The results showed that welding with a dual optic setup with a defocused secondary beam reduced the volumetric porosity in the weld to 5%. The highest levels of volumetric porosity were 30%, and were a result of using the dual optic setup, but with a defocused primary beam. No clear relation between the level of porosity and power or welding speed was found. It was found that the amount of porosity depended on the balance of the energy input (controlled by defocusing) between the two beams. Porosity formation can be reduced if the energy from the first beam results in the nucleation and initial growth of pores. Reheating by the second beam then allows the pores to grow and escape from the molten material without melting additional base material. Furthermore, twin-spot welding is shown to be a promising combination of a production friendly solution and high quality welding.