Trace of B and Ga can substitute for Mo in Mn-Si-Cr dual phase steels.The technological process and CCT curves of steels treated with B and Ga are similar to those for Mn-Si-Cr-Mo steel.
The slow phase transformation of microalloyed dual phase steel makes the nonuniform stress and temperature fields during the post rolling cooling process have a significant impact on the phase transformation process.G...The slow phase transformation of microalloyed dual phase steel makes the nonuniform stress and temperature fields during the post rolling cooling process have a significant impact on the phase transformation process.Given the relatively slow phase transformation of DP780 steel within the microalloyed dual phase steel series,the influence of stress on the phase transformation behavior of DP780 steel was investigated.To quantify the nonuniform thermal and stress conditions in the steel coil,a thermo-mechanical coupled finite element model of the hot-rolled strip cooling process was established.Based on the simulation data,DP780 steel was chosen as the research material,and Gleeble 3500 thermal simulation equipment was used for experimental validation.The thermal expansion curves were analyzed through regression to establish the dynamic model of DP780 steel phase transformation under stress.Subsequently,metallographic analysis was conducted to determine phase transformation type and grain size of DP780 steel.The results confirmed that the stress promotes the occurrence of semi-diffusion-type bainite transformation.Furthermore,an appropriate level of stress facilitates the growth of bainitic grains,while the increased stress inhibits the growth of ferritic grains.展开更多
The effects of Nb addition,individually and in combination with Ti,were evaluated over a range of coiling temperatures.Coiling temperature influences the ratio of soluble and precipitated Nb in the hot rolled steel co...The effects of Nb addition,individually and in combination with Ti,were evaluated over a range of coiling temperatures.Coiling temperature influences the ratio of soluble and precipitated Nb in the hot rolled steel containing 0.08 % C and 2.2 % Mn.Nb bearing precipitates can co-precipitate on TiN and impact the microstructure and mechanical properties of the steel after annealing treatment.Microstructure characterization revealed that recovery and recrystallization processes preceded austenite formation.The effects of Nb on austenite formation in cold rolled steels during heating and isothermal holding and on austenite decomposition during subsequent cooling were investigated using dilatometry.The addition of Nb retarded ferrite recrystallization starting temperature,but had no significant effect on the starting temperature of austenite formation during heating.The Nb addition also accelerated austenite formation once the transformation started,and was beneficial for the formation of a finer and homogeneous microstructure.展开更多
A theorectical expression for the driving force and M_(?) point of martensitic transformation has been proposed.The M_(?) values using this expression are in good agreement with that obtained experimentally.It was fou...A theorectical expression for the driving force and M_(?) point of martensitic transformation has been proposed.The M_(?) values using this expression are in good agreement with that obtained experimentally.It was found that the values of M_(?) and M_(?) are not only related to the carbon content in martensite,but also to the volume fraction of ferrite.展开更多
The fine grained dual phase （FG-DP） steel with ferrite grains of 2-4.5 μm and martensite islands smaller than 3 μm was obtained through the mechanism of deformation-enhanced ferrite transformation （DEFT）. Mechan...The fine grained dual phase （FG-DP） steel with ferrite grains of 2-4.5 μm and martensite islands smaller than 3 μm was obtained through the mechanism of deformation-enhanced ferrite transformation （DEFT）. Mechanical properties of the steel were tested at room temperature. The results indicated that with a similar volume fraction of martensite （about 20vol%）,FG-DP steel exhibited a superior combination of higher strength and more rapid strain hardening at low strains compared with the coarse-grained dual phase （CG-DP） steel obtained by critical annealing. The combination of higher strength,large elongation,and more rapid strain hardening of FG-DP steel can be attributed to the fine ferrite grain and finely dispersed martensite islands. In addition,the uniformly distributed martensite islands in FG-DP steel have smaller interspacing compared with that of CG-DP steel. So,at the initial plastic deformation stage,the plastic deformation of ferrite was restrained and more pronounced load was transferred from ferrite to martensite. The plastic deformation of martensite in FG-DP steel started earlier.展开更多
The C-Mn and C-Mn-Nb steels were thermo-mechanically processed to develop dual phase steel and to study the effect of controlled rolling on the martensitic hardenability of austenite. The steel specimens were intercri...The C-Mn and C-Mn-Nb steels were thermo-mechanically processed to develop dual phase steel and to study the effect of controlled rolling on the martensitic hardenability of austenite. The steel specimens were intercritically annealed at 790℃, rolled at that temperature to the reductions of 10%, 23%, and 47% and immediately cooled at different rates. Quantitative metallography was used to construct the microstructure map, which illustrated that increasing deformation progressively reduced the proportion of new ferrite formed at all cooling rates and increased the amount of martensite at fast and intermediate rates. The martensitic hardenability of austenite remaining after all the rolling reductions was plotted as a function of cooling rates. It was observed that for the austenite-martensite conversion efficiencies greater than about 25%, controlled rolling increased the martensitic hardenability of austenite.展开更多
With the development of advanced high strength steel,especially for dual-phase steel,the model algorithm for cooling control after hot rolling has to achieve the targeted coiling temperature control at the location of...With the development of advanced high strength steel,especially for dual-phase steel,the model algorithm for cooling control after hot rolling has to achieve the targeted coiling temperature control at the location of downcoiler whilst maintaining the cooling path control based on strip microstructure along the whole cooling section.A cooling path control algorithm was proposed for the laminar cooling process as a solution to practical difficulties associated with the realization of the thermal cycle during cooling process.The heat conduction equation coupled with the carbon diffusion equation with moving boundary was employed in order to simulate temperature change and phase transformation kinetics,making it possible to observe the temperature field and the phase fraction of the strip in real time.On this basis,an optimization method was utilized for valve settings to ensure the minimum deviations between the predicted and actual cooling path of the strip,taking into account the constraints of the cooling equipment′s specific capacity,cooling line length,etc.Results showed that the model algorithm was able to achieve the online cooling path control for dual-phase steel.展开更多
Bake-hardening behaviour of carbon steel with different martensite morphologies and volume fraction was investigated. The specimens with fibrous and bulky martensite were prestrained in tension by 4%. After this, they...Bake-hardening behaviour of carbon steel with different martensite morphologies and volume fraction was investigated. The specimens with fibrous and bulky martensite were prestrained in tension by 4%. After this, they were unloaded and bake hardened at 180 ℃ for 10-160 min. It was found that dual-phase steel samples which were bake hardened at 180 ℃ for 20 rain showed an increase in the yield stress （YS） and ultimate tensile stress （UTS） but a decrease in ductility. Further increase in the bake-hardening time of 80 or 160 min has reduced the YS and UTS, but increased the ductility. △σ （increase in stress due to bake hardening）, YS and UTS values are higher for the microstructure containing fibrous martensite compared to the microstructure-containing bulky martensite. It was also observed that at a given baking temperature Aa, YS and UTS increased by volume of martensite.展开更多
文摘Trace of B and Ga can substitute for Mo in Mn-Si-Cr dual phase steels.The technological process and CCT curves of steels treated with B and Ga are similar to those for Mn-Si-Cr-Mo steel.
基金supported by the National Natural Science Foundation of China(Grant No.52004029).
文摘The slow phase transformation of microalloyed dual phase steel makes the nonuniform stress and temperature fields during the post rolling cooling process have a significant impact on the phase transformation process.Given the relatively slow phase transformation of DP780 steel within the microalloyed dual phase steel series,the influence of stress on the phase transformation behavior of DP780 steel was investigated.To quantify the nonuniform thermal and stress conditions in the steel coil,a thermo-mechanical coupled finite element model of the hot-rolled strip cooling process was established.Based on the simulation data,DP780 steel was chosen as the research material,and Gleeble 3500 thermal simulation equipment was used for experimental validation.The thermal expansion curves were analyzed through regression to establish the dynamic model of DP780 steel phase transformation under stress.Subsequently,metallographic analysis was conducted to determine phase transformation type and grain size of DP780 steel.The results confirmed that the stress promotes the occurrence of semi-diffusion-type bainite transformation.Furthermore,an appropriate level of stress facilitates the growth of bainitic grains,while the increased stress inhibits the growth of ferritic grains.
文摘The effects of Nb addition,individually and in combination with Ti,were evaluated over a range of coiling temperatures.Coiling temperature influences the ratio of soluble and precipitated Nb in the hot rolled steel containing 0.08 % C and 2.2 % Mn.Nb bearing precipitates can co-precipitate on TiN and impact the microstructure and mechanical properties of the steel after annealing treatment.Microstructure characterization revealed that recovery and recrystallization processes preceded austenite formation.The effects of Nb on austenite formation in cold rolled steels during heating and isothermal holding and on austenite decomposition during subsequent cooling were investigated using dilatometry.The addition of Nb retarded ferrite recrystallization starting temperature,but had no significant effect on the starting temperature of austenite formation during heating.The Nb addition also accelerated austenite formation once the transformation started,and was beneficial for the formation of a finer and homogeneous microstructure.
文摘A theorectical expression for the driving force and M_(?) point of martensitic transformation has been proposed.The M_(?) values using this expression are in good agreement with that obtained experimentally.It was found that the values of M_(?) and M_(?) are not only related to the carbon content in martensite,but also to the volume fraction of ferrite.
基金the Major State Basic Research and Development Program of China (No2004CB619102)
文摘The fine grained dual phase （FG-DP） steel with ferrite grains of 2-4.5 μm and martensite islands smaller than 3 μm was obtained through the mechanism of deformation-enhanced ferrite transformation （DEFT）. Mechanical properties of the steel were tested at room temperature. The results indicated that with a similar volume fraction of martensite （about 20vol%）,FG-DP steel exhibited a superior combination of higher strength and more rapid strain hardening at low strains compared with the coarse-grained dual phase （CG-DP） steel obtained by critical annealing. The combination of higher strength,large elongation,and more rapid strain hardening of FG-DP steel can be attributed to the fine ferrite grain and finely dispersed martensite islands. In addition,the uniformly distributed martensite islands in FG-DP steel have smaller interspacing compared with that of CG-DP steel. So,at the initial plastic deformation stage,the plastic deformation of ferrite was restrained and more pronounced load was transferred from ferrite to martensite. The plastic deformation of martensite in FG-DP steel started earlier.
文摘The C-Mn and C-Mn-Nb steels were thermo-mechanically processed to develop dual phase steel and to study the effect of controlled rolling on the martensitic hardenability of austenite. The steel specimens were intercritically annealed at 790℃, rolled at that temperature to the reductions of 10%, 23%, and 47% and immediately cooled at different rates. Quantitative metallography was used to construct the microstructure map, which illustrated that increasing deformation progressively reduced the proportion of new ferrite formed at all cooling rates and increased the amount of martensite at fast and intermediate rates. The martensitic hardenability of austenite remaining after all the rolling reductions was plotted as a function of cooling rates. It was observed that for the austenite-martensite conversion efficiencies greater than about 25%, controlled rolling increased the martensitic hardenability of austenite.
文摘With the development of advanced high strength steel,especially for dual-phase steel,the model algorithm for cooling control after hot rolling has to achieve the targeted coiling temperature control at the location of downcoiler whilst maintaining the cooling path control based on strip microstructure along the whole cooling section.A cooling path control algorithm was proposed for the laminar cooling process as a solution to practical difficulties associated with the realization of the thermal cycle during cooling process.The heat conduction equation coupled with the carbon diffusion equation with moving boundary was employed in order to simulate temperature change and phase transformation kinetics,making it possible to observe the temperature field and the phase fraction of the strip in real time.On this basis,an optimization method was utilized for valve settings to ensure the minimum deviations between the predicted and actual cooling path of the strip,taking into account the constraints of the cooling equipment′s specific capacity,cooling line length,etc.Results showed that the model algorithm was able to achieve the online cooling path control for dual-phase steel.
文摘Bake-hardening behaviour of carbon steel with different martensite morphologies and volume fraction was investigated. The specimens with fibrous and bulky martensite were prestrained in tension by 4%. After this, they were unloaded and bake hardened at 180 ℃ for 10-160 min. It was found that dual-phase steel samples which were bake hardened at 180 ℃ for 20 rain showed an increase in the yield stress （YS） and ultimate tensile stress （UTS） but a decrease in ductility. Further increase in the bake-hardening time of 80 or 160 min has reduced the YS and UTS, but increased the ductility. △σ （increase in stress due to bake hardening）, YS and UTS values are higher for the microstructure containing fibrous martensite compared to the microstructure-containing bulky martensite. It was also observed that at a given baking temperature Aa, YS and UTS increased by volume of martensite.
