Research on the longitudinal protection of a through-type cophase traction direct power supply system based on the empirical wavelet transform

This paper proposes a longitudinal protection scheme utilizing empirical wavelet transform(EWT)for a through-type cophase traction direct power supply system,where both sides of a traction network line exhibit a distinctive boundary structure.This approach capitalizes on the boundary’s capacity to attenuate the high-frequency component of fault signals,resulting in a variation in the high-frequency transient energy ratio when faults occur inside or outside the line.During internal line faults,the high-frequency transient energy at the checkpoints located at both ends surpasses that of its neighboring lines.Conversely,for faults external to the line,the energy is lower compared to adjacent lines.EWT is employed to decompose the collected fault current signals,allowing access to the high-frequency transient energy.The longitudinal protection for the traction network line is established based on disparities between both ends of the traction network line and the high-frequency transient energy on either side of the boundary.Moreover,simulation verification through experimental results demonstrates the effectiveness of the proposed protection scheme across various initial fault angles,distances to faults,and fault transition resistances.

Traction power systems for electrified railways:evolution,state of the art,and future trends

Traction power systems(TPSs)play a vital role in the operation of electrified railways.The transformation of conventional railway TPSs to novel structures is not only a trend to promote the development of electrified railways toward high-efficiency and resilience but also an inevitable requirement to achieve carbon neutrality target.On the basis of sorting out the power supply structures of conventional AC and DC modes,this paper first reviews the characteristics of the existing TPSs,such as weak power supply flexibility and low-energy efficiency.Furthermore,the power supply structures of various TPSs for future electrified railways are described in detail,which satisfy longer distance,low-carbon,high-efficiency,high-reliability and high-quality power supply requirements.Meanwhile,the application prospects of different traction modes are discussed from both technical and economic aspects.Eventually,this paper introduces the research progress of mixed-system electrified railways and traction power supply technologies without catenary system,speculates on the future development trends and challenges of TPSs and predicts that TPSs will be based on the continuous power supply mode,employing power electronic equipment and intelligent information technology to construct a railway comprehensive energy system with renewable energy.

New generation traction power supply system and its key technologies for electrified railways

Unlike the traditional traction power supply system which enables the electrified railway traction sub- station to be connected to power grid in a way of phase rotation, a new generation traction power supply system without phase splits is proposed in this paper. Three key techniques used in this system have been discussed. First, a combined co-phase traction power supply system is applied at traction substations for compensating negative sequence current and eliminating phase splits at exits of substations; design method and procedure for this system are presented. Second, a new bilateral traction power supply technology is proposed to eliminate the phase split at section post and reduce the influence of equalizing current on the power grid. Meanwhile, power factor should be adjusted to ensure a proper voltage level of the traction network. Third, a seg- mental power supply technology of traction network is used to divide the power supply arms into several segments, and the synchronous measurement and control technology is applied to diagnose faults and their locations quickly and accurately. Thus, the fault impact can be limited to a min- imum degree. In addition, the economy and reliability of the new generation traction power supply system are analyzed.

Test Analysis of Traction Battery Peak Power

The test process of electric vehicles (EVs) traction battery peak power is analyzed in detail. Aimed at a special “traction” design of versatile battery—HORIZON~ C~2M Battery, the features are introduced. According to the peak power test schedule, the test parameters of HORIZON~ C~2M Battery are calculated and the charging and discharging experiments are carried out. The sustained (30 s) discharge power capability of battery at 2/3 of its open circuit voltage at each of various depths of discharge is determined. The dynamic internal resistance under peak power test is established. Considering the temperature impact during discharging, the peak power capability at each of various depths of discharge is corrected. The correctness of peak power test is validated by combining theory analysis with test results.

Industrial frequency single-phase AC traction power supply system for urban rail transit and its key technologies

To avoid stray current and maintain the benefit of no phase-split in the DC traction power supply system, an AC traction power supply system was proposed for the urban public transport such as metro and light rail transit. The proposed system consists of a main substation （MSS） and cable traction network （CTN）. The MSS includes a single-phase main traction transformer and a negative-se- quence compensation device, while the CTN includes double-core cables, traction transformers, overhead catenary system, rails, etc. Several key techniques for the proposed system were put forward and discussed, which can be summarized as （1） the power supply principle, equivalent circuit and transmission ability of the CTN, the cable-catenary matching technique, and the selection of catenary voltage level; （2） the segmentation technology and status identification method for traction power supply network, distributed and centralized protection schemes, etc.; （3） a power supply scheme for single-line MSS and a power supply scheme of MSS shared by two or more lines. The proposed industrial frequency single-phase AC traction power supply system shows an excellent technical performance, good economy, and high reliability, hence provides a new alternative for metro and urban rail transit power supply systems.

Power management in co-phase traction power supply system with super capacitor energy storage for electrified railways

Increasing railway traffic and energy utilization issues prompt electrified railway systems to be more economical,efficient and sustainable.As regenerative braking energy in railway systems has huge potential for optimized utilization,a lot of research has been focusing on how to use the energy efficiently and gain sustainable benefits.The energy storage system is an alternative because it not only deals with regenerative braking energy but also smooths drastic fluctuation of load power profile and optimizes energy management.In this work,we propose a co-phase traction power supply system with super capacitor(CSS_SC)for the purpose of realizing the function of energy management and power quality management in electrified railways.Besides,the coordinated control strategy is presented to match four working modes,including traction,regenerative braking,peak shaving and valley filling.A corresponding simulation model is built in MATLAB/Simulink to verify the feasibility of the proposed system under dynamic working conditions.The results demonstrate that CSS_SC is flexible to deal with four different working conditions and can realize energy saving within the allowable voltage unbalance of 0.008%in simulation in contrast to 1.3%of the standard limit.With such a control strategy,the performance of super capacitor is controlled to comply with efficiency and safety constraints.Finally,a case study demonstrates the improvement in power fluctuation with the valley-to-peak ratio reduced by 20.3%and the daily load factor increased by 17.9%.

Traction power substation balance and losses estimation in AC railways using a power transfer device through Monte Carlo analysis

The high dynamic power requirements present in modern railway transportation systems raise research challenges for an optimal operation of railway electrification. This paper presents a Monte Carlo analysis on the application of a power transfer device installed in the neutral zone and exchanging active power between two sections. The main analyzed parameters are the active power balance in the two neighbor traction power substations and the system power losses. A simulation framework is presented to comprise the desired analysis and a universe of randomly distributed scenarios are tested to evaluate the effectiveness of the power transfer device system. The results show that the density of trains and the relative branch length of a traction power substation should be considered in the evaluation phase of the best place to install a power transfer device, towards the reduction of the operational power losses, while maintaining the two substations balanced in terms of active power.

A preventive opportunistic maintenance method for railway traction power supply system based on equipment reliability

Conventional maintenance mode for the traction power supply system(TPSS)is to perform scheduled regular maintenance activities for power supply equipment,while such maintenance mode may result in undue maintenance tasks and low efficiency due to different degradation processes of different sorts of equipment.To address this problem,this paper introduces a preventive opportunistic maintenance(POM)method for TPSS based on equipment reliability.Firstly,a POM model is established by considering the equipment reliability degradation process based on Weibull distribution.Then,by considering the total power outage time in the planned operation cycle of TPSS as the optimization objective,the optimal maintenance scheme of TPSS is formulated by iterative method of maintenance strategies.The proposed method is verified by introducing practical maintenance strategies and fault record data of the traction transformer,circuit breaker and disconnector in an actual TPSS of a railway administration.Results show that the presented method can make full use of the existing fault data to develop a POM scheme for TPSS.It can improve maintenance efficiency and reduce power outage time,providing guidance to formulate scientific maintenance strategies for TPSS.

Scheme of long distance power supply for electrified railway traction network based on traction cable

Purpose–The traction cable is paralleled with the existing traction network of electrified railway through transverse connecting line to form the scheme of long distance power supply for the traction network.This paper aims to study the scheme composition and power supply distance(PSD)of the scheme.Design/methodology/approach–Based on the structure of parallel traction network(referred to as“cable traction network(CTN)”),the power supply modes(PSMs)are divided into cableþdirect PSM and cableþautotransformer(AT)PSM(including Japanese mode,French mode and new mode).Taking cableþJapanese AT PSM as an example,the scheme of long distance power supply for CTN under the PSMs of co-phase and out-of-phase power supply are designed.On the basis of establishing the equivalent circuit model and the chain circuit model of CTN,taking the train working voltage as the constraint condition,and based on the power flow calculation of multiple train loads,the calculation formula and process for determining the PSD of CTN are given.The impedance and PSD of CTN under the cableþAT PSM are simulated and analyzed,and a certain line is taken as an example to compare the scheme design.Findings–Results show that the equivalent impedance of CTN under the cableþAT PSM is smaller,and the PSD is about 2.5 times of that under the AT PSM,which can effectively increase the PSD and the flexibility of external power supply location.Originality/value–The research content can effectively improve the PSD of traction power supply system and has important reference value for the engineering application of the scheme.

Comparison of Three Modes of AT-fed Traction Power Networks

The features of three modes of AT-fed traction power networks (TPNs) have been briefly described in the existing literature, which is not adequate yet. In this paper, these three modes of TPNs are compared mainly on TPN capacity, transformer capacity, rail potential and voltage level, etc., and conclusions are drawn.

Investigation of Power Factor Behavior in AC Railway System Based on Special Traction Transformers

The single-phase traction load has essentially an unbalance characteristic at the Point of Common Coupling (PCC), which injects harmonic into the utility grid. In this paper, the effect of harmonic distortion and unbalance loading are investigated simultaneously for electrical railway systems. Special traction transformers (i.e. single-phase, V/V, Wye-Delta, Scott, and Le Blanc) are used between the utility grid and the traction load. For analysis, different defini-tions of power factors are considered, which are presented by IEEE Std.1459. The detailed simulation study is made with MATLAB/SIMULINK program to represent the impacts of harmonic components and unbalance loading on the power factor behavior in the Electrical Railway systems.

Improved fault location method for AT traction power network based on EMU load test

The autotransformer(AT)neutral current ratio method is widely used for fault location in the AT traction power network.With the development of high-speed electrified railways,a large number of data show that the relation between the AT neutral current ratio and the distance from the beginning of the fault AT section to the fault point(Q-L relation)is mostly nonlinear.Therefore,the linear Q-L relation in the traditional fault location method always leads to large errors.To solve this problem,a large number of load-related current data that can be used to describe the Q-L relation are obtained through the load test of the electric multiple unit(EMU).Thus,an improved fault location method based on the back propagation(BP)neural network is proposed in this paper.On this basis,a comparison between the improved method and the traditional method shows that the maximum absolute error and the average absolute error of the improved method are 0.651 km and 0.334 km lower than those of the traditional method,respectively,which demonstrates that the improved method can effectively eliminate the influence of nonlinear factors and greatly improve the accuracy of fault location for the AT traction power network.Finally,combined with a shortcircuit test,the accuracy of the improved method is verified.

计及光伏和储能接入的牵引供电系统能量管理策略

近年来,为实现电气化铁路“双碳”目标,多项铁路用能优化举措投入实施并取得一定成效,然而,单靠能耗优化治标不治本。为根治电气化铁路碳排放问题,在保证系统稳定运行的基础上,基于智能电网理念,提出计及光伏和储能接入的牵引供电系统能量管理策略。首先,构建计及光伏和储能接入的牵引供电系统;然后,基于电力市场电价及新能源出力,采用日前联合调控、日内滚动调节和实时优化控制铁路用能,并通过分层分级优化,打破各“源”端相对独立、各自为政的壁垒,实现多能互补;最后,通过共享储能模式,降低储能装置闲置率并提高新能源利用率。仿真结果表明,该能量管理策略可在保障系统运行稳定和安全的基础上有效地降低系统的运行成本,同时保持良好的电能质量。

基于RPC的光储接入牵引供电系统协调控制方法

为将光伏发电接入牵引供电系统进行有效利用,同时兼顾牵引供电系统电能质量改善及列车再生制动能量回收利用,提出了一种基于铁路功率调节器的光储系统接入牵引供电系统的协调控制方法.首先,搭建基于铁路功率调节器的光储系统接入牵引供电拓扑结构,并对其电能质量补偿机理进行理论分析;在此基础上,充分考虑光储系统的运行条件以及列车牵引、制动、空载或惰行工况,提出光储系统接入牵引供电的联合协调控制方法,实现了“光+储+荷”三者间的协调控制、牵引供电系统负序的动态补偿以及谐波的有效抑制;在RT-Lab实时仿真系统中建立了基于铁路功率调节器的光伏接入牵引供电系统仿真模型,并结合实际光照和牵引工况数据验证本文所提出的系统结构以及协调控制方法的有效性.结果表明:本文所提出的系统结构以及协调控制方法能够实现牵引供电系统中光储系统的有效接入,再生制动能量回收率提升至86.7%,功率因数提升6.4%,对谐波特别是高次谐波含有率有较大改善,满足光伏电能高效消纳及综合利用、电能质量动态综合补偿、再生制动能量回收多重需求.

新型混合式贯通牵引供电系统及其复合控制策略

电分相与负序等电能质量问题是制约电气化铁路向高速化、重载化发展的桎梏。贯通牵引供电系统为消弭上述问题提供了契机,但既有贯通方案依然存在所需器件数目多、改造成本高、可靠性差等弊端。为此,在充分利用既有牵引变压器基础上,该文设计一种新型混合式贯通牵引供电装置。该装置通过共直流侧与功率均分手段有效抵消输入侧纹波功率,降低有源/无源器件数目与电容容量。同时,针对直流侧二次纹波与负荷功率冲击,提出一种输入端口复合控制策略,有效解决纹波传递与冲击波动问题。最后通过仿真与实验验证所提装置及其控制策略的可行性与可靠性。

隧道牵引分区所雷击暂态特性及其二次设备电磁兼容研究

牵引供电系统遭受雷击会在分区所内产生过电压与过电流,对分区所开关柜中二次设备产生瞬态电磁干扰,影响其正常运行。文中针对电气化铁路隧道分区所,建立雷击暂态仿真模型,计算了接触网不同位置遭受雷击时分区所的过电压与过电流,建立了27.5 kV开关柜的电磁场有限元仿真模型,分析开关柜中不同区域的瞬态电场、磁场分布。结果表明:雷击接触网会在分区所内产生幅值较大、频率较高的过电压与过电流,在其作用下开关柜低压室瞬态电场可达147.2 V/m、瞬态磁场可达1.3 kA/m,断路器室前壁处瞬态电场可达822.9 kV/m、瞬态磁场可达15.85 kA/m,超过标准规定的幅值,二次设备需要考虑相应的电磁屏蔽措施。论文结果对牵引供电系统雷击过电压/电流防护以及二次设备电磁兼容设计具有参考价值。

上海轨道交通崇明线牵引供电制式方案研究

[目的]为了解决传统采用钢轨回流的直流牵引供电系统存在杂散电流腐蚀、直流供电距离受限等问题。[方法]对国内外主要城市轨道交通AC 25 kV/50 Hz牵引供电制式和直流牵引供电制式的应用情况、技术特点、适用性等指标进行对比分析后,结合上海轨道交通崇明线工程的特殊性,提出采用DC 1500 V架空接触网+负极专用回流轨的牵引供电方式;针对在越江段隧道内是否设置牵引变电所设计了两种供电方案,仿真计算了两种方案下供电系统供电能力达到24对/h时牵引网最低电压、整流机组功率和牵引变电所有效电流等指标,并进行了比较分析。[结果及结论]采用负极专用回流轨的直流牵引供电制式可从根本上杜绝杂散电流的产生及其对周边管线的腐蚀;在长距离越江区段设置牵引变电所方案与牵引直流设备“双套配置”方案相比,前者的供电可靠性和供电能力更具优势。

基于馈线和电流的专用轨回流牵引供电系统接地故障保护

对于专用轨回流牵引供电系统,负极回流轨对地具有良好的绝缘特性,极大地限制了正极接地故障所产生的短路电流。由于负极母线电位下降、接地电阻较大等原因,现有的正极接地保护在实际应用中暴露出选择性差、灵敏度低等问题。本文通过对专用轨回流牵引供电系统短路电流以及负荷电流的潮流分析,提出以供电区间馈线和电流作为正极接地故障判断的特征量,并设计基于该故障特征量的保护方案,基于MATLAB/Simulink仿真系统,验证了该保护方案的有效性。

基于多导体回路法的AT供电方式长回路电容计算方法研究

提出了一种基于多导体回路法以接触网和正馈线为传输导体的电气化铁路AT供电方式牵引网长回路电容计算方法。该方法以与电荷唯一对应的回路为基本单元,对复杂多导体传输线系统开展电场描述,实现了AT供电方式牵引网长回路电容的精确计算。

基于ZYNQ的动车组牵引网电能质量监测装置

针对动车组运营时牵引网的电能质量问题,文中基于ZYNQ平台设计了一种适用于动车组的牵引网电能质量监测装置。选用ZYNQ-7000系列的XC7Z045芯片作为装置主控芯片,采用模块设计,主要包括信号采集模块、信号处理模块和数据传输模块。信号采集模块使用AD9251芯片实现对电压电流原始数据的同步高速采集;信号处理模块利用主控芯片中内含的双核ARM Cortex-A9构成的PS以及FPGA构成的PL实现数据的高速处理;数据传输模块利用以太网芯片和网络变压器构建千兆网络电路实现数据的高速传输。实验结果证明:该装置性能稳定、计算精度高,各项参数计算误差在0.5%之内,满足动车组牵引网的电能质量监测需求。