Development and validation of an HPLC-UV method for analysis of methylphenidate hydrochloride and loxapine succinate in an activated carbon disposal system

Unused medications have the possibility of being abused, causing serious harm to individuals who were not prescribed the drug. The Food and Drug Administration(FDA) recommends the proper disposal of unused prescribed medications to maintain safety and prevent environmental hazards. However, many of the current disposal techniques do not properly address safety. A drug disposal pouch containing granular activated carbon offers a unique disposal method to deactivate residual or expired medication in a convenient, effective, and safe manner. A robust and validated method for methylphenidate hydrochloride and loxapine succinate was developed using high-performance liquid chromatography(HPLC) and the deactivation efficiency of the disposal system was tested. Methylphenidate hydrochloride was analyzed on a C18 analytical column(250 mm ?4.60 mm, 100?) using acetonitrile-water(0.05%(v/v) trifluoroacetic acid) as the mobile phase at a flow rate of1.0 mL/min with a run time of 15 min and retention time of 7.8 min. Loxapine succinate was separated on a C8100?(250 mm ? 4.6 mm, 5 mm) column maintained at 25 °C using a flow rate of 1.0 mL/min. The run time was 10 min and the retention time of the drug was around 4.6 min. Mobile phase was composed of acetonitrile and water(0.3% triethylamine) at pH 3.0 as 40:60(v/v). Reference standard solutions(100 mg/mL) for both drugs were prepared by dissolving in mobile phases. These methods provide good linearity(R2? 0.999) over the range of 5–100 mg/mL for methylphenidate hydrochloride and 0.1–100 mg/mL for loxapine succinate. The assay methods were successfully applied to study the deactivation of these drugs.

Measuring methods for three kinds of polyhydroxyalkanoates from activated sludge by gas chromatography

Gas chromatography determination of polyhydroxyalkanoates has been common;however,the pretreatment steps are often complex,and gas chromatography operation conditions are not given in detail.In this study,gas chromatography is used for analyzing PHB,PHV and PH2MV,three majors of PHAs in activated sludge.The sample was centrifuged at a speed of 4000 r/min for the separation of floc and supernatant,freezen,and dried for 12 h in vacuum freezing drier;and then transferred to the fridge for freezing to ice and drying for 12 h in vacuum freezing drier;then chloroform and a simple composition digestion solution including methanol,sulfuric acid and benzoic acid was added;digested at 105 ℃ for 6 h;cooled to room temperature,the lower solution of the result can be used for analyzing.Samples were analyzed by gas chromatography with FID detector and auto sampler;the standard curve of standard material shows an excellent linear relationship with correlation coefficients larger than 0.99;the relative standard deviation (RSD) of sludge samples is less than 1%.The recovery rates of each sample are between 95%-105%.The GC analysis time of each PHA sample is shorter than 10 minutes.

Preparation of AZ91D magnesium alloy semi-solid billet by new strain induced melt activated method

New strain induced melt activated (new SIMA) method for preparing AZ91D magnesium alloy semi-solid billet is introduced by applying equal channel angular extrusion into strain induced step in SIMA method, by which semi-solid billet with fine spheroidal grains and average grain size of 18 μm can be prepared. Furthermore, average grain size of semi-solid billet is reduced with increasing extrusion pass of AZ91D magnesium alloy obtained in ECAE process. By using semi-solid billet prepared by new SIMA, thixoforged magazine plates component with high mechanical properties such as yield strength of 201.4 MPa, ultimate tensile strength of 321.8 MPa and elongation of 15.3%, can be obtained.

“Three Methods and Three Points” regulates p38 mitogen-activated protein kinase in the dorsal horn of the spinal cord in a rat model of sciatic nerve injury

Tuina is a traditional Chinese treatment for sensory disturbances caused by peripheral nerve injury and related diseases. Our previous studies showed that tuina regulates relevant regions and indices of the spinal dorsal horn using the Dian, Bo, and Rou method in Yinmen（BL37）, Yanglingquan（GB34）, and Weizhong（BL40）. Treatment prevents muscle atrophy, protects spinal cord neurons, and promotes sciatic nerve repair. The mechanisms of action of tuina for treating peripheral nerve injury remain poorly understood. This study established rat models of sciatic nerve injury using the crushing method. Rats received Chinese tuina in accordance with the principle of ＂Three Methods and Three Points,＂ once daily for 20 days. Tuina intervention reduced paw withdrawal latency and improved wet weight of the gastrocnemius muscle, as well as promoting morphological recovery of sciatic nerve fibers, Schwann cells, and axons. The protein expression levels of phospho-p38 mitogen-activated protein kinase, tumor necrosis factor-α, and interleukin-1β also decreased. These findings indicate that ＂Three Methods and Three Points＂ promoted morphological recovery and improved behavior of rats with peripheral nerve injury.

Study on Component Synthesis Active Vibration Suppression Method Using Zero-placement Technique

The component synthesis active vibration suppression method （CSVS） can be applied to suppress the vibration of flexible systems. By this method, several same or similar time-varying components are arranged according to certain rules along the time axis. The synthesized command can suppress the arbitrary unwanted vibration harmonic while achieving the desired rigid body motion. The number of the components increases rapidly when the number of harmonic vibration is growing. In this article, the CSVS based on zero-placement technique is used to construct the synthesized command to suppress the multi-harmonics simultaneously in the discrete domain. The nature of zero-placement method is to put enough zeros to cancel system poles at necessary points. The designed synthesized command has equal time intervals between each component and which is much easier to be implemented. Using this method, the number of components increases linearly with the increasing of the number of being suppressed harmonics. For the spacecraft with flexible appendages, CSVS based on zero-placement is used to design the time optimal large angle maneuver control strategy. Simulations have verified the validity and superiority of the proposed approach.

Effects of Different Nitrogen Application Methods on Enzyme Activities in Leaves at Late Growth Stage of Spring Maize

[Objective] This paper aimed at exploring the effects of different nitrogen application methods on the enzyme activities of leaves at ear position in late growth stage of maize. [Method] By pot experiment, the superoxide dismutase （SOD） activity, peroxidase （POD） activity, malonyl dialdehyde （MDA） content and soluble protein content were determined. [Result] At the filling stage and ripening stage, with the increasing of nitrogen application rate, MDA content gradually decreased, while SOD activity, POD activity and soluble protein content increased. MDA content with two topdressing nitrogen was lower than that with one top dressing nitrogen at the same nitrogen application rate, while SOD activity, POD activity and soluble protein content with two topdressing nitrogen were higher than that with one topdressing nitrogen. [Conclusion] Different nitrogen application methods have relatively significant effects on the MDA content, SOD activity, POD activity and soluble protein content, which is of certain directive significance for preventing spring maize prematuration.

Chemoselective Transfer Hydrogenation of Cinnamaldehyde over Activated Charcoal Supported Pt/Fe3O4 Catalyst

A variety of spherical and structured activated charcoal supported Pt/Fe3O4 composites with an average particle size of ~100 nm have been synthesized by a self-assembly method using the difference of reduction potential between Pt （Ⅳ） and Fe （Ⅱ） precursors as driving force. The formed Fe3O4 nanoparticles （NPs） effectively prevent the aggregation of Pt nanocrystallites and promote the dispersion of Pt NPs on the surface of catalyst, which will be favorable for the exposure of Pt active sites for high-efficient adsorption and contact of substrate and hydrogen donor. The electron-enrichment state of Pt NPs donated by Fe304 nanocrystallites is corroborated by XPS measurement, which is responsible for promoting and activating the terminal C=O bond of adsorbed substrate via a vertical configuration. The experimental results show that the activated charcoal supported Pt/Fe3O4 catalyst exhibits 94.8% selectivity towards cinnamyl alcohol by the transfer hydrogenation of einnamaldehyde with Pt loading of 2.46% under the optimum conditions of 120 ℃ for 6 h, and 2-propanol as a hydrogen donor. Additionally, the present study demonstrates that a high-efficient and recyclable catalyst can be rapidly separated from the mixture due to its natural magnetism upon the application of magnetic field.

Adsorption Performance of Activated Carbon Prepared from Corn Stalks

[Objective] This study aimed to study the adsorption performance of activated carbon prepared from corn stalks. [Methed] With granular activated carbon prepared from corn stalks as research object, adsorption performance simulation test equipment was set up to investigate the adsorption performance of the prepared activated carbon for methanol by static weight method. In addition, the effects of adsorption bed structure, activated carbon particle size in adsorption bed, addition amount of graphite powder in activated carbon and modified activated carbon on systematic adsorption performance were studied. [Result] Under conditions of same activated carbon and same adsorption temperature, the adsorption performance of new adsorption bed A （installed with finned diaphragm adsorbate tubes） was signifi- cantly better than that of unmodified adsorption bed B. Compared with adsorption bed B, adsorption bed A took 5 min shorter to reach the adsorption amount of 0.22 g/g. Under the same adsorption temperature, the adsorption performance of bed loaded with different-particle size activated carbon was significantly better than that loaded with same-particle size activated carbon. The bed loaded with different-particle size activated carbon took 16 min shorter to reach the adsorption capacity of 0.22 g/g compared with the bed loaded with same-particle size activated carbon. Adding proper amount of graphite powder in activated carbon could enhance the thermal conductivity and strengthen the adsorption properties. The optimum addition amount of graphite powder was 20% of the total amount of activated carbon. Com- pared with that of the control, the adsorption performance of activated carbon soaked by weak acidic solution was significantly improved. It took 3 min shorter to reach 87.1% of the equilibrium adsorption amount. [Conclusion] This study will provide reference for optimizing structural design of adsorption bed and adsorption refrigeration system.

Total phenolic, flavonoid content, and antioxidant activity of flour, noodles, and steamed bread made from different colored wheat grains by three milling methods

The objective of this study was to evaluate the effects of wheat variety, food processing, and milling method on antioxidant properties. Black wheat variety Heibaoshi 1 had the highest total phenolic content(659.8 μg gallic acid equivalents g-1), total flavonoid content(319.3 μg rutin equivalents g-1), and antioxidant activity, whereas light purple wheat variety Shandongzimai 1 had the lowest total flavonoid content(236.2 μg rutin equivalents g-1) and antioxidant activity. Whole wheat flour and partially debranned grain flour had significantly higher total phenolic contents, total flavonoid contents, and antioxidant activity than refined flour(P < 0.05). Compared with flour, total phenolic contents, total flavonoid contents and antioxidant activity decreased in noodles and steamed bread, whereas noodles had slightly higher total phenolic and flavonoid content than steamed bread. Antioxidant activities(by ferric reducing ability of plasma assay) of steamed bread made from whole wheat flour, partially debranned grain flour, and refined flour were 23.5%, 21.1%, and 31.6% lower, respectively, than the corresponding values of flour. These results suggested that black whole wheat flour and partially debranned grain flour are beneficial to human health.

Inactivated properties of activated carbon-supported TiO_2 nanoparticles for bacteria and kinetic study

The activated carbon-supported TiO2 nanoparticles(TiO2/AC)were prepared by a properly controlled sol-gel method.The effects of activated carbons(AC)support on inactivated properties of TiO2 nanoparticles were evaluated by photocatalytic inactivation experiments of Escherichia coli.The key factors affecting the inactivation effciency were investigated,including electric power of lamp, temperature,and pH values.The results show that the TiO2/AC composites have high inactivation properties of E.coli in compari...

Grain Size and Photocatalytic Activity of Nanometer TiO_2 Thin Films Prepared by the Sol-gel Method

Transparent anatase TiO2 nanometer thin films with photocatalytic activity were prepared via the sol-gel method on soda-lime glass. The thickness , crystalline phase, grain size, surface hydroxyl amount and so on were characterized by scanning electron microscopy (SEM) , X-ray diffraction (XRD), transmission electron microscopy ( TEM), X-ray photoelectron spectroscopy (XPS) and UV-visible spectrophotometer ( UV-VIS). The photocatalytic activity of TiO2 thin films was evaluated for the photocatalytic decolorization of aqueous methyl orange . The effects of film thickness on the crystalline phase, grain size, transmittance and photocatalytic activity of nanometer Ti02 thin films were discussed.

Rapid communication Preparation of TiO_2 nanometer thin films with high photocatalytic activity by reverse micellar method

Two kinds of TiO_2 nanometer thin films were prepared on stainless steel bythe reverse micellar and sol-gel methods, respectively. The calcined TiO_ 2 thin films werecharacterized by X-ray diffraction (XRD), atomic force microscopy (AFM), BET surface area and X-rayphotoelectron spectroscopy (XPS). Photocatalytic activity was evaluated by photocatalyticdecoloration of methyl orange aqueous solution. The results showed that the TiO_2 thin filmsprepared by reverse micellar method (designated as RM-TiO_2 films) showed higher photocatalyticactivity than those by sol-gel method (designated as SG-TiO_2 films). This is attributed to the factthat the former is composed of smaller monodispersed spherical particles with a size of about 15 nmand possesses higher surface areas.

An Irregular Wave Maker of Active Absorption with VOF Method

A numerical irregular wave flume with active absorption of re-reflected waves is simulated by use of volume of fluid （VOF） method. An active ＇absorbing wave-maker based on linear wave theory is set on the left boundary of the wave flume. The progressive waves and the absorbing waves are generated simultaneously at the active wave generating-absorbing boundary. The absorbing waves are generated to eliminate the waves coming back to the generating boundary due to reflection from the outflow boundary and the structures. SIRW method proposed by Frigaard and Brorsen （1995） is used to separate the incident waves and reflected waves. The digital filters are designed based on the surface elevation signals of the two wave gauges. The corrected velocity of the wave-maker paddle is the output from the digital filter in real time. The numerical results of regular and irregular waves by the active absorbing-generating boundary are compared with the numerical results by the ordinary generating boundary to verify the performance of the active absorbing-generator boundary. The differences between the initial incident waves and the estimated incident waves are analyzed.

Effect of Preparation Methods of Bi_(2)O_(3) Nanoparticles on their Photocatalytic Activity

Bi 2O 3 nanoparticles were prepared by means of ammonia precipitation, polyol mediated methods and microemulsion chemical method. The structure and properties of the as-prepared nanoparticles, having been submitted to a heat-treatment test at 750 ℃, were characterized by means of XRD, BET, XPS and UV-Vis absorption techniques. The photocatalytic oxidation reactions of benzene, toluene and xylene were used as the model reaction to measure the photocatalytic activity of Bi 2O 3 nanoparticles, respectively. The results show that the crystallite size of Bi 2O 3 prepared with different methods and calcined at 750 ℃ were 50.6, 38.5 and 31.5 nm, respectively. The photocatalytic activity of Bi 2O 3 nanoparticles prepared with the microemulsion chemical method was higher than that of the particles prepared with the polyol mediated method; and that of the particles prepared with the micromulsion chemical method was the highest among the three. The degradation rates of the three pollutants xylene, toluene and benzene decreased in sequence.

Forecast daily indices of solar activity, F10.7, using support vector regression method

The 10.7 cm solar radio flux （F10.7）, the value of the solar radio emission flux density at a wavelength of 10.7 cm, is a useful index of solar activity as a proxy for solar extreme ultraviolet radiation. It is meaningful and important to predict F10.7 values accurately for both long-term （months-years） and short-term （days） forecasting, which are often used as inputs in space weather models. This study applies a novel neural network technique, support vector regression （SVR）, to forecasting daily values of F10.7. The aim of this study is to examine the feasibility of SVR in short-term F10.7 forecasting. The approach, based on SVR, reduces the dimension of feature space in the training process by using a kernel-based learning algorithm. Thus, the complexity of the calculation becomes lower and a small amount of training data will be sufficient. The time series of F10.7 from 2002 to 2006 are employed as the data sets. The performance of the approach is estimated by calculating the norm mean square error and mean absolute percentage error. It is shown that our approach can perform well by using fewer training data points than the traditional neural network.

Theoretical and Experimental Study on the Adsorption and Desorption of Methane by Granular Activated Carbon at 25℃

A theoretical and experimental study was conducted to accurately determine the amount of adsorption and desorption of methane by various Granular Activated Carbon （GAC） under different physical conditions. To carry out the experiments, the volumetric method was used up to 500 psia at constant temperature of 25℃. In these experiments, adsorption as well as desorption capacities of four different GAC in the adsorption of methane, the major constituent of natural gas, at various equilibrium pressures and a constant temperature were studied. Also, various adsorption isotherm models were used to model the experimental data collected from the experiments. The accuracy of the results obtained from the adsorption isotherm models was compared and the values for the regressed parameters were reported. The results shows that the physical characteristics of activated carbons such as BET surface area, micropore volume, packing density, and pore size distribution play an important role in the amount of methane to be adsorbed and desorbed.

A Generalized Limit Equilibrium Method for the Solution of Active Earth Pressure on a Retaining Wall

In this paper, a generalized limit equilibrium method of solving the active earth pressure problem behind a retaining wall is proposed.Differing from other limit equilibrium methods, an arbitrary slip surface shape without any assumptions of pre-defined shapes is needed in the current framework, which is verified to find the most probable failure slip surface. Based on the current computational framework, numerical comparisons with experiment, discrete element method and other methods are carried out. In addition, the influences of the inclination of the wall, the soil cohesion, the angle of the internal friction of the soil, the slope inclination of the backfill soil on the critical pressure coefficient of the soil, the point of application of the resultant earth pressure and the shape of the slip surface are also carefully investigated. The results demonstrate that limit equilibrium solution from predefined slip plane assumption, including Coulomb solution, is a special case of current computational framework. It is well illustrated that the current method is feasible to evaluate the characteristics of earth pressure problem.

Adsorption of congo red on mesoporous activated carbon prepared by CO2 physical activation

This research demonstrates the production of mesoporous activated carbon from sargassum fusiforme via physical activation with carbon dioxide.Central composite design was applied to conduct the experiments at different levels by altering three operating parameters.Activation temperature(766-934℃),CO2 flow rate(0.8-2.8 L·min^-1)and activation time(5-55 min)were the variables examined in this study.The effect of parameters on the specific surface area,total pore volume and burn-out rate of activated carbon was studied,and the influential parameters of methylene blue adsorption value were identified employing analysis of variance.The optimum conditions for maximum methylene blue adsorption value were:activation temperature=900℃,activation time=29.05 min and CO2 flow rate=1.8 L·min(-1).The activated carbon produced under optimum conditions was characterized by BET,FTIR and SEM.The adsorption behavior on congo red was studied.The effect of parameters on the adsorbent dosage,temperature,PH and initial congo red concentration was investigated.The adsorption properties of the activated carbon were investigated by kinetics.The equilibrium removal rate and maximum adsorption capacity reaches up to 94.72%,234 mg·g^-1,respectively when initial congo red concentration is 200 mg·L^-1 under adsorbent dosage(0.8 g·L^-1),temperature(30℃),PH7.

Measurement of mouse liver glutathione S-transferase activity by the integrated method

Objective: The integrated method was investigated to measure Vm/Km of mouse liver glutathione S-transfer-ase (GST) activity on GSH and 7-Cl-4-nitrobenzofurazozan. Methods: Presetting concentration of one substrate twenty-fold above the other's and taking maximum product absorbance Am as parameter while Km as constant, Vm/Km was obtained by nonlinear fitting of GST reaction curve to the integrated Michaelis-Menten equation In [Am/(Am -Ai)] + Ai/ ( ξ× Km ) = ( Vm/Km )×ti (1). Results: Vm/Km for GST showed slight dependence on initial substrate concentration and data range, but it was resistant to background absorbance, error in reaction origin and small deviation in presetting Km. Vm/Km was proportional to the amount of GST with upper limit higher than that by initial rate. There was close correlation between Vm/Km and initial rate of the same GST. Consistent results were obtained by this integrated method and classical initial rate method for the measurement of mouse liver GST. Conclusion: With the concentration of one substrate twenty-fold above the other's, this integrated method was reliable to measure the activity of enzyme on two substrates , and substrate concentration of the lower one close to its apparent Km was able to be used.

Advances in Studies on Extraction Methods and Physiological Activities of Jujube Flavonoids

Jujube is rich in nutrients and functional active ingredients. For example,jujube flavonoids have significant anti-oxidation,anticancer,antibacterial and anti-inflammatory functions. This paper elaborated the advances in the studies about the extraction methods,purification methods,antioxidant properties,stability and antibacterial effects of jujube flavonoids,in order to provide a certain reference for the study of jujube flavonoids.