The evolution of morphology, composition, thickness and corrosion resistance of the oxide film on pure Sn solder substrate submitted to high-temperature aging in 150 °C dry atmosphere was investigated. The result...The evolution of morphology, composition, thickness and corrosion resistance of the oxide film on pure Sn solder substrate submitted to high-temperature aging in 150 °C dry atmosphere was investigated. The results indicate that high-temperature aging accelerates the dehydration of Sn(OH)_(4)in the pre-existing native oxide film to form SnO_(2)and facilitates the oxidation of fresh Sn substrate, resulting in the gradual increase in oxide film thickness and surface roughness with prolonging aging time. However, the corrosion resistance of the film initially is enhanced and then deteriorated with an extending aging time. Besides, the formation and evolution mechanisms of the oxide film with aging time were discussed.展开更多
The electrochemical migration（ECM） behavior and mechanism of immersion silver processing circuit board（PCB-ImAg）and hot air solder leveling circuit board（PCB-HASL） under the 0.1 mol/L Na2SO4 absorbed thin liquid...The electrochemical migration（ECM） behavior and mechanism of immersion silver processing circuit board（PCB-ImAg）and hot air solder leveling circuit board（PCB-HASL） under the 0.1 mol/L Na2SO4 absorbed thin liquid films with different thicknesses were investigated using stereo microscopy and scanning electron microscopy（SEM）.Meanwhile,the corrosion tendency and kinetics rule of metal plates after bias application were analyzed with the aid of electrochemical impedance spectroscopy（EIS）and scanning Kelvin probe（SKP）.Results showed that under different humidity conditions,the amount of migrating corrosion products of silver for PCB-ImAg was limited,while on PCB-HASL both copper dendrites and precipitates such as sulfate and metal oxides of copper/tin were found under a high humidity condition（exceeding 85%）.SKP results indicated that the cathode plate of two kinds of PCB materials had a higher corrosion tendency after bias application.An ECM model involving multi-metal reactions was proposed and the differences of ECM behaviors for two kinds of PCB materials were compared.展开更多
Formation of AuSnx intermetallic compounds （IMCs） in laser reflowed solder joints was investigated. The results showed that few IMCs formed at the solder/0. 1μm Au interface. Needlelike AuSn4 IMCs were observed at ...Formation of AuSnx intermetallic compounds （IMCs） in laser reflowed solder joints was investigated. The results showed that few IMCs formed at the solder/0. 1μm Au interface. Needlelike AuSn4 IMCs were observed at the solder/0.5μm Au interface. In Sn-2.0Ag-O,75Cu-3,0Bi and Sn-3.5Ag-O.75Cu solder joints, when the laser input energy was increased, AuSn4 IMCs changed .from a layer to needlelike or dendritic distribution at the solder/0.9μm Au interface. As for the solder joints with 4.0 μm thickness of Au surface finish on pads, AuSn4 , AuSnx, AuSn IMCs, and Au2Sn phases formed at the interface. Moreover, the content of AuSnx IMCs, such as, AuSn4 and AuSn2, which contained high Sn concentration, would become larger as the laser input energy increased. In the Sn-37Pb solder joints with 0.9 μm or 4.0 μm thickness of the Au surface finish on pads, AuSn4 IMCs were in netlike distribution. The interspaces between them were filled with Pb-rich phases.展开更多
基金financial support from CAS Key Laboratory of Nuclear Materials and Safety Assessment, Institute of Metal Research, Chinese Academy of Sciences。
文摘The evolution of morphology, composition, thickness and corrosion resistance of the oxide film on pure Sn solder substrate submitted to high-temperature aging in 150 °C dry atmosphere was investigated. The results indicate that high-temperature aging accelerates the dehydration of Sn(OH)_(4)in the pre-existing native oxide film to form SnO_(2)and facilitates the oxidation of fresh Sn substrate, resulting in the gradual increase in oxide film thickness and surface roughness with prolonging aging time. However, the corrosion resistance of the film initially is enhanced and then deteriorated with an extending aging time. Besides, the formation and evolution mechanisms of the oxide film with aging time were discussed.
基金Project(51271032)supported by the National Natural Science Foundation of China
文摘The electrochemical migration（ECM） behavior and mechanism of immersion silver processing circuit board（PCB-ImAg）and hot air solder leveling circuit board（PCB-HASL） under the 0.1 mol/L Na2SO4 absorbed thin liquid films with different thicknesses were investigated using stereo microscopy and scanning electron microscopy（SEM）.Meanwhile,the corrosion tendency and kinetics rule of metal plates after bias application were analyzed with the aid of electrochemical impedance spectroscopy（EIS）and scanning Kelvin probe（SKP）.Results showed that under different humidity conditions,the amount of migrating corrosion products of silver for PCB-ImAg was limited,while on PCB-HASL both copper dendrites and precipitates such as sulfate and metal oxides of copper/tin were found under a high humidity condition（exceeding 85%）.SKP results indicated that the cathode plate of two kinds of PCB materials had a higher corrosion tendency after bias application.An ECM model involving multi-metal reactions was proposed and the differences of ECM behaviors for two kinds of PCB materials were compared.
基金This study was financially supported by National Natural Science Foundation of China （No.50675047）.
文摘Formation of AuSnx intermetallic compounds （IMCs） in laser reflowed solder joints was investigated. The results showed that few IMCs formed at the solder/0. 1μm Au interface. Needlelike AuSn4 IMCs were observed at the solder/0.5μm Au interface. In Sn-2.0Ag-O,75Cu-3,0Bi and Sn-3.5Ag-O.75Cu solder joints, when the laser input energy was increased, AuSn4 IMCs changed .from a layer to needlelike or dendritic distribution at the solder/0.9μm Au interface. As for the solder joints with 4.0 μm thickness of Au surface finish on pads, AuSn4 , AuSnx, AuSn IMCs, and Au2Sn phases formed at the interface. Moreover, the content of AuSnx IMCs, such as, AuSn4 and AuSn2, which contained high Sn concentration, would become larger as the laser input energy increased. In the Sn-37Pb solder joints with 0.9 μm or 4.0 μm thickness of the Au surface finish on pads, AuSn4 IMCs were in netlike distribution. The interspaces between them were filled with Pb-rich phases.
