Ag-ZSM-5 Catalyst for the Catalytic Decomposition of NO

The catalytic decomposition of NO over Ag-ZSM-5 catalyst prepared by ion-exchange was investigated. The exchanged silver in the zeolite was reduced and it collected in the course of the reaction to form silver particles of about 20 nm. The catalytic reaction induced a pronounced restructuring of the Ag particles through preferential formation of the (111) facets. These facets were shown to hind a tightly bound oxygen species (O-gamma). The O-gamma species occupies the active sites for NO adsorption resulting in catalyst deactivation. It could be removed by appropriate reducing agents, such as CO, to recover the active sites at elevated temperatures.

CuO/Co_(3)O_(4)Bifunctional Catalysts for Electrocatalytic 5-Hydroxymethylfurfural Oxidation Coupled Cathodic Ammonia Production

The electrochemical coupling of biomass oxidation and nitrogen conversion presents a potential strategy for high value-added chemicals and nitrogen cycling.Herein,in this work,CuO/Co_(3)O_(4)with heterogeneous interface is successfully constructed as a bifunctional catalyst for the electrooxidation of 5-hydroxymethylfurfural to 2,5-furandicarboxylic acid and the electroreduction of nitrate to ammonia(NH_(3)).The open-circuit potential spontaneous experiment shows that more 5-hydroxymethylfurfural molecules are adsorbed in the Helmholtz layer of the CuO/Co_(3)O_(4)composite,which certifies that the CuO/Co_(3)O_(4)heterostructure is conducive to the kinetic adsorption of 5-hydroxymethylfurfural.In situ electrochemical impedance spectroscopy further shows that CuO/Co_(3)O_(4)has faster reaction kinetics and lower reaction potential in oxygen evolution reaction and 5-hydroxymethylfurfural electrocatalytic oxidation.Moreover,CuO/Co_(3)O_(4)also has a good reduction effect on NO_(3)^(-).The ex-situ Raman spectroscopy shows that under the reduction potential,the metal oxide is reduced,and the generated Cu_(2)O can be used as a new active site for the reaction to promote the electrocatalytic conversion of NO_(3)^(-)to NH_(3) synthesis.This work provides valuable guidance for the synthesis of value-added chemicals by 5-hydroxymethylfurfural electrocatalytic oxidation coupled with NO_(3)^(-)while efficiently producing NH_(3).

Ag-ZSM-5催化剂上CH_4选择催化还原NO_x的研究

摘要 研究Ａｇ－ＺＳＭ－５催化剂上ＣＨ４选择性催化还原ＮＯｘ的反应性能,采用ＴＰＤ和ＴＰＳＲ技术研究ＮＯ和Ｏ２共吸附于Ａｇ－ＺＳＭ－５催化剂表面形成的吸附物种及其和ＣＨ４之间的反应．结果表明,Ａｇ－ＺＳＭ－５催化剂上ＣＨ４选择性还原ＮＯｘ活性和选择性较高．ＮＯ和Ｏ２共吸附在Ａｇ－ＺＳＭ－５催化剂上形成的ＮＯ３(ｓ)吸附物种能被ＣＨ４还原生成Ｎ２．在ＮＯ３(ｓ)和Ｏ２共存的体系中,ＣＨ４能优先并选择性还原ＮＯ３(ｓ)生成Ｎ２．

Selective hydrogenolysis of biomass-derived furfuryl alcohol into 1,2- and 1,5-pentanediol over highly dispersed Cu-Al_2O_3 catalysts

Cu nanoparticles supported on a variety of oxide supports, including SiO2, TiO2, ZrO2, Al2O3, MgO and ZnO, were investigated for the hydrogenolysis of biomass‐derived furfuryl alcohol to1,2‐pentanediol and 1,5‐pentanediol. A Cu‐Al2O3 catalyst with 10 wt% Cu loading prepared by a co‐precipitation method exhibited the best performance in terms of producing pentanediols compared with the other materials. This catalyst generated an 85.8% conversion and a 70.3% combined selectivity for the target pentanediols at 413 K and 8 MPa H2 over an 8‐h reaction. The catalyst could also be recycled over repeated reaction trials without any significant decrease in productivity. Characterizations with X‐ray diffraction, NH3/CO2‐temperature programmed desorption, N2 adsorption,transmission electron microscopy and N2 O chemisorption demonstrated that intimate and effective interactions between Cu particles and the acidic Al2O3 support in this material greatly enhanced its activity and selectivity. The promotion of the hydrogenolysis reaction was found to be especially sensitive to the Cu particle size, and the catalyst with Cu particles 1.9 to 2.4 nm in size showed the highest turnover frequency during the synthesis of pentanediols.

汽车尾气净化催化剂Ag-ZSM-5选择性催化还原NO

评价了Ag-ZSM-5分子筛催化剂选择性还原NO的活性,并运用原位漫反射红外光谱研究NO在该催化剂上的选择性还原机理.结果表明,以丙烯为还原剂,有O2(3.6%)存在时,Ag-ZSM-5有良好活性,在773K时NO还原成N2的转化率达68.8%.基于漫反射红外光谱,认为NO还原为N2的过程中,NO以NOx吸附态形式与丙烯的活化物种CxHy或CxHyOz反应,生成有机-氮氧化物(R-NO2或R-ONO)中间体,再进一步反应,最终生成N2;催化剂表面形成有机-氮氧化物是关键步骤,Ag的作用是促进形成NOx,O2 的作用是促进C3H6活化及NO转化成NOx,并且O2是有效产生有机-氮氧化物不可缺少的条件.

NH_3 selective catalytic reduction of NO: A large surface TiO_2 support and its promotion of V_2O_5 dispersion on the prepared catalyst

A titania support with a large surface area was developed, which has a BET surface area of 380.5 m^2/g, four times that of a traditional titania support. The support was ultrasonically impregnated with 5 wt% vanadia. A special heat treatment was used in the calcination to maintain the large surface area and high dispersion of vanadium species. This catalyst was compared to a common V2O5-TiO2 catalyst with the same vanadia loading prepared by a traditional method. The new catalyst has a surface area of 117.7 m^2/g, which was 38% higher than the traditional V2O5-TiO2 catalyst. The selective catalytic reduction（SCR） performance demonstrated that the new catalyst had a wider temperature window and better N2 selectivity compared to the traditional one. The NO conversion was 80% from 200 to 450 °C. The temperature window was 100 °C wider than the traditional catalyst. Raman spectra indicated that the vanadium species formed more V-O-V linkages on the catalyst prepared by the traditional method. The amount of V-O-Ti and V=O was larger for the new catalyst. Temperature programmed desorption of NH3, temperature programmed reduction by H2 and X-ray photoelectron spectroscopy results showed that its redox ability and total acidity were enhanced. The results are helpful for developing a more efficient SCR catalyst for the removal of NOx in flue gases.

原位漫反射红外光谱研究氮氧化物在Ag-ZSM-5催化剂上的吸附态及选择性催化还原反应机理

利用原位分析方法对催化剂表面吸附态进行动态表征 ,对了解催化反应机理具有重要的意义。漫反射红外光谱是一种理想的原位方法 ,应用该方法在 2 98～ 773K范围原位考察了以丙烯为还原剂 ,NO在Ag ZSM 5催化剂上的吸附态及选择性催化还原过程。认为NO的选择性催化还原符合直接作用机理 ,还原的关键是形成有机 氮氧化物 (R NO2 或R ONO)中间体。O2 的作用是使C3H6 充分活化 ,并是有效产生有机

Hydrogen Production by Low-temperature Steam Reforming of Bio-oil over Ni/HZSM-5 Catalyst

We investigated high catalytic activity of Ni/HZSM-5 catalysts synthesized by the impregnation method, which was successfully applied for low-temperature steam reforming of bio-oil. The influences of the catalyst composition, reforming temperature and the molar ratio of steam to carbon fed on the stream reforming process of bio-oil over the Ni/HZSM-5 catalysts were investigated in the reforming reactor. The promoting effects of current passing through the catalyst on the bio-oil reforming were also studied using the electrochemical catalytic reforming approach. By comparing Ni/HZSM-5 with commonly used Ni/Al2O3 catalysts, the Ni2O/ZSM catalyst with Ni-loading content of about 20% on the HZSM-5 support showed the highest catalytic activity. Even at 450 ℃, the hydrogen yield of about 90% with a near complete conversion of bio-oil was obtained using the Ni2O/ZSM catalyst. It was found that the performance of the bio-oil reforming was remarkably enhanced by the HZSM-5 supporter and the current through the catalyst. The features of the Ni/HZSM-5 catalysts were also investigated via X-ray diffraction, inductively coupled plasma and atomic emission spectroscopy, hydrogen temperature-programmed reduction, and Brunauer-Emmett-Teller methods.

纤维素直接制备5-羟甲基糠醛的研究进展

5-羟甲基糠醛(HMF)是一种重要的生物基平台化合物,被美国能源部评为12种最具潜力的生物基平台化合物之一。制取HMF最有效的方法是酸催化己糖脱水,己糖在自然界中数量有限,而纤维素在自然界中广泛存在,直接以纤维素为原料制备HMF避免了己糖的分离,具有更高的经济效益。纤维素由于其特殊的化学结构,不溶于水和一般的有机溶剂,反应活性较低,纤维素转化为HMF首先的障碍是纤维素的水解。文章从纤维素结构出发,基于纤维素催化转化制备HMF的反应机理,综述了近年来纤维素制备HMF中纤维素预处理的方法、溶剂体系、催化剂体系的研究进展,并对纤维素制备HMF的发展前景进行了展望,以期为相关研究工作提供一定的参考。

Methane aromatization in the absence of oxygen over extruded and molded MoO_3/ZSM-5 catalysts:Influences of binder and molding method

The influences of binder and molding method on the catalytic performance of methane aromatization in the absence of O2 over MoO3/ZSM-5 catalysts were investigated.SEM,NH3-TPD,FT-IR of adsorbed pyridine,N2 adsorption-desorption,cyclohexane adsorption and XPS were employed to characterize the physical and chemical properties of the catalysts.It was found that SiO2 was a suitable binder for the catalyst due to its appropriate weak acidity.The laminar catalyst comprising of an inert spherical core and a MoO3/ZSM-5 laminar shell with 0.1 0.2 mm in thickness showed a better catalytic performance than the extruded catalyst.The improved activity of the laminar catalyst could be attributed to the easy carbonization of Mo species and the quick removal of reaction products from the catalyst surface.

Preparation and Catalytic Application of Novel Water Tolerant Solid Acid Catalysts of Zirconium Sulfate/HZSM-5

Esterification of acrylic acid（AA） to produce AA esters has widespread application in the chemical industry. A series of water tolerant solid acid catalysts was prepared, and characterized by XRD, nitrogen adsorption, TGA-DTA, XPS, and ammonia adsorption FTIR. The effects of Si/Al ratio, zirconium sulfate（ZS） loading on HZSM-5 and calcination temperature on the esterification were investigated. When 20% （mass fraction） ZS is loaded on HZSM-5, the conversion of AA reaches 100%. XRD analysis indicates that ZS is highly dispersed on HZSM-5 because no crystalline structure assigned to ZS is found. Catalytic activity and hydrophobicity of ZS supported on HZSM-5 are higher compared with those of parent ZS or HZSM-5. Results show that this kind of novel catalysts is an efficient water tolerant solid acid catalyst for esterification reactions.

Effects of ZrO_2 on the Performance of CuO-ZnO-Al_2O_3/HZSM-5 Catalyst for Dimethyl Ether Synthesis from CO_2 Hydrogenation

A series of composite catalysts were prepared by the wet mixing method, and the mass ratio of CuO-ZnO-Al2O3-ZrO2 component to HZSM-5 zeolite （molar ratio of SiO2 to Al2O3 being 25） was 2：1. The CuO-ZnO-Al2O3-ZrO2 （CuO/ZnO/Al2O3=3/6/1 by weight） component was prepared by a modified ＇two-step＇ co-precipitation method. The effects of ZrO2 on the performance of CuO-ZnO-Al2O3/HZSMo5 catalyst for dimethyl ether synthesis from CO2 hydrogenation were investigated. It was found that ZrO2 improved the properties of CuO-ZnO-Al2O3/HZSM-5 as a structural promoter.

Effects of Temperature and Catalyst to Oil Weight Ratio on the Catalytic Conversion of Heavy Oil to Propylene Using ZSM-5 and USY Catalysts

It is useful for practical operation to study the rules of production of propylene by the catalytic conversion of heavy oil in FCC （fluid catalytic cracking）. The effects of temperature and C/O ratio （catalyst to oil weight ratio） on the distribution of the product and the yield of propylene were investigated on a micro reactor unit with two model catalysts, namely ZSM-5/Al2O3 and USY/Al2O3, and Fushun vacuum gas oil （VGO） was used as the feedstock. The conversion of heavy oil over ZSM-5 catalyst can be comparable to that of USY catalyst at high temperature and high C/O ratio. The rate of conversion of heavy oil using the ZSM-5 equilibrium catalyst is lower compared with the USY equilibrium catalyst under the general FCC conditions and this can be attributed to the poor steam ability of the ZSM-5 equilibrium catalyst. The difference in pore topologies of USY and ZSM-5 is the reason why the principal products for the above two catalysts is different, namely gasoline and liquid petroleum gas （LPG）, repspectively. So the LPG selectivity, especially the propylene selectivity, may decline if USY is added into the FCC catalyst for maximizing the production of propylene. Increasing the C/O ratio is the most economical method for the increase of LPG yield than the increase of the temperature of the two model catalysts, because the loss of light oil is less in the former case. There is an inverse correlation between HTC （hydrogen transfer coefficient） and the yield of propylene, and restricting the hydrogen transfer reaction is the more important measure in increasing the yield of propylene of the ZSM-5 catalyst. The ethylene yield of ZSM-5/A1203 is higher, but the gaseous side products with low value are not enhanced when ZSM-5 catalyst is used. Moreover, for LPG and the end products, dry gas and coke, their ranges of reaction conditions to which their yields are dependent are different, and that of end products is more severe than that of LPG. So it is clear that maximizing LPG and propylene and restricting dry gas and coke can be both achieved via increasing the severity of reaction conditions among the range of reaction conditions which LPG yield is sensitive to.

Efficient conversion of fructose to 5-hydroxymethylfurfural over sulfated porous carbon catalyst

Sulfated porous carbon （PC-SO3H） catalyst was successfully synthesized from one-pot treatment of porous polydivinylbenzene in H2SO4 at 250 ℃, which exhibited very good catalytic performances in the production of 5-hydroxymethylfurfural from fructose.

Effects of Calcination Temperature on the Acidity and Catalytic Performances of HZSM-5 Zeolite Catalysts for the Catalytic Cracking of n-Butane

The acidic modulations of a series of HZSM-5 catalysts were successfully made by calcination at different treatment temperatures, i.e. 500, 600, 650, 700 and 800 ℃, respectively. The results indicated that the total acid amounts, their density and the amount of B-type acid of HZSM-5 catalysts rapidly decreased, while the amounts of L-type acid had almost no change and thus the ratio of L/B was obviously enhanced with the increase of calcination temperature （excluding 800 ℃）. The catalytic performances of modified HZSM-5 catalysts for the cracking of n-butane were also investigated. The main properties of these catalysts were characterized by means of XRD, N2 adsorption at low temperature, NH3-TPD, FTIR of pyridine adsorption and BET surface area measurements. The results showed that HZSM-5 zeolite pretreated at 800 ℃ had very low catalytic activity for n-butane cracking. In the calcination temperature range of 500-700 ℃, the total selectivity to olefins, propylene and butene were increased with the increase of calcination temperature, while, the selectivity for arene decreased with the calcination temperature. The HZSM-5 zeolite calcined at 700 ℃ produced light olefins with high yield, at the reaction temperature of 650 ℃ the yields of total olefins and ethylene were 52.8% and 29.4%, respectively. Besides, the more important role is that high calcination temperature treatment improved the duration stability of HZSM-5 zeolites. The effect of calcination temperature on the physico-chemical properties and catalytic performance of HZSM-5 for cracking of n-butane was explored. It was found that the calcination temperature had large effects on the surface area, crystallinity and acid properties of HZSM-5 catalyst, which further affected the catalytic performance for n-butane cracking.

Low-temperature activation of methane over rare earth metals promoted Zn/HZSM-5 zeolite catalysts in the presence of ethylene

At low temperature of 723 K, methane can be easily activated in the presence of ethylene in the feed, and converted to higher hydrocarbons （C2-C4） and aromatics （C6-C10）, through its reaction over rare metals modified Zn/HZSM-5 zeolite catalysts without undesirable carbon oxides formation. Methane can get 37.3% conversion over the above catalysts under low temperature, and the catalysts show a longer lifetime than usual metal supported HZSM-5 zeolite catalysts without adding any rare earth metals. The effects of methane activation over various rare earth metal promoted Zn/HZSM-5 catalysts on the products and influences of several reaction conditions such as temperature, catalyst lifetime and molar ratio of CH4/C2H4 have been discussed.

Introduction of table sugar as a soft second template in ZSM-5 nanocatalyst and its effect on product distribution and catalyst lifetime in methanol to gasoline conversion

Methanol to gasoline reaction was investigated on two prepared ZSM-5 catalysts. The first one was a conventional catalyst denoted as ZSM-5（C） and the other was a hierarchical catalyst-ZSM-5（S） which was prepared by incorporation of table sugar in catalyst gel during the synthesis procedure. The catalysts were characterized by FTIR, XRD, FE-SEM, N2 adsorption-desorption, NH3-TPD and TGA analytical technics. The proposed material showed pore modification as well as acidity moderating properties in ZSM-5 catalyst. The methanol to gasoline reaction was conducted in a fixed bed reactor with a WHSV of 1.5 h-1.Methanol conversions, gasoline yield and selectivity in production for the synthesized catalysts were determined by gas chromatography method. The sugar modified catalyst converted more methanol than the conventional one and an enhancement in catalyst’s life time was observed. The selectivity to aromatics and durene were reduced compared to the conventional catalyst, so the gasoline quality was also further improved. The coking rate of catalysts was calculated employing TGA method. A reduction in coking rate and an increase in coke capacity of the modified catalyst were observed.

ZSM-5/MAPO Composite Catalyst for Converting Methanol to Olefins in a Two-Stage Unit with a Dimethyl Ether Pre-Reactor

A ZSM-5/MAPO composite catalyst was prepared by adding ZSM-5 zeolite powder to a conventional molecular sieve synthesis system, followed by modification with NH_4H_2PO_4. The samples were characterized by XRD, SEM, IR, NH_3-TPD, and BET analyses. The catalytic property of the samples toward the methanol-to-olefin(MTO) reaction was evaluated in a connected in series two-stage unit equipped with a continuous flow(once-through) fixed-bed tubular reactor similar to an industrial reactor. The first reactor mainly converted methanol into dimethyl ether and water, followed by being subject to continuous reaction in the second reactor, in which DME was converted to hydrocarbons. The composites exhibited the typical framework topology of MFI, AEI and AFI, which represented the ZSM-5 zeolite, the molecular sieves AlPO-18 or SAPO-18, AlPO-5 or SAPO-5, respectively. The composites showed several advantages for optimizing the zeolite acidity, enhancing the mass transfer, and restraining the side reactions. Catalytic reaction results showed that the composites exhibited higher selectivity to light olefins(84.0%) and lower selectivity to C_2―C_4 alkanes and C_5^+ hydrocarbons than pure ZSM-5. Moreover, the composite zeolite loaded with 3% of P demonstrated improved catalytic activity and stability for the conversion of methanol to propylene, because the coking rate was obviously suppressed.

Effect of Ga Addition on Catalytic Performance of PtSnNa/ZSM-5 Catalyst for Propane Dehydrogenation

PtSnNaGa/ZSM-5 catalysts with different contents of Ga were prepared and characterized by X-ray diffraction (XRD), nitrogen adsorption, hydrogen chemisorption, ammonia temperature-programmed desorption (NH3-TPD), hydrogen temperature-programmed reduction (H2-TPR), and temperature-programmed oxidation (TPO) techniques. The performances of these catalysts for propane dehydrogenation were investigated. The test results indicated that the addition of Ga not only could improve the catalytic stability and propene selectivity, but also could effectively prevent the catalysts from coking. It was found that the PtSnNaGa(0.5 m%)/ZSM-5 catalyst exhibited the best performance in terms of propene selectivity and propane conversion. The high catalytic performance was most probably attributed to the presence of Ga that could strength- en the interaction between metals and the support to stabilize the catalytic active sites.

Highly efficient production of 2,5-dihydroxymethylfuran from biomass-derived 5-hydroxymethylfurfural over an amorphous and mesoporous zirconium phosphonate catalyst

The development of high-efficiency and low-cost catalysts is very crucial for the MeerweinPonndorf-Verley (MPV) reduction of biomass-derived 5-hydroxymethylfurfural (HMF) into 2,5-dihydroxymethylfuran (DHMF). In this work, an amorphous and mesoporous zirconium phosphonate catalyst (Zr-DTMP), which is a zirconium-containing organic-inorganic nanohybrid, was successfully designed and synthesized by the simple assembly of zirconium tetrachloride (ZrCl4) and diethylene triaminepenta(methylene phosphonic acid)(DTMP). Satisfactorily, when Zr-DTMP was employed for the MPV reduction of HMF in the presence of 2-butanol (secBuOH), DHMF yield could be achieved as 96.5% in 3 h under a relatively mild reaction temperature of 140℃. Systematic investigations indicated that this high catalytic activity should be mainly due to the cooperative role of enhancive Lewis acid site (Zr4+) and Lewis base site (O2-) in activating the carbonyl group of HMF and dissociating the hydroxyl group of secBuOH, respectively. Additionally, Zr-DTMP showed excellent catalytic stability, when it was successively used 5 recycles, its surface characteristics and textural properties still remained almost unchanged, and so, the catalytic activity was not obviously affected. More interestingly, Zr-DTMP could also be applied for the selective reduction of other biomass-derived carbonyl compounds, such as 5-methylfurfural (MF), furfural (FF), levulinic acid (LA), ethyl levulinate (EL) and cyclohexanone (CHN), into the corresponding products with high yields, which is beneficial to the effective synthesis of various valuable bio-based chemicals.