A heterojunction structure design is a very good method for improving the properties of semiconductors in many research fields.This method is employed in the present study to promote the gas-sensing performance of Ag_...A heterojunction structure design is a very good method for improving the properties of semiconductors in many research fields.This method is employed in the present study to promote the gas-sensing performance of Ag_(3)PO_(4)nanocomposites at room temperature(25℃).A nanocomposite of Ag_(3)PO_(4)nanoparticles and three-dimensional peony-like WO_(3)(WO_(3)/Ag_(3)PO_(4))was successfully prepared by the precipitation method.The crystalline phases were analyzed by xray diffraction and the microstructure was characterized by scanning electron microscopy and transmission electron microscopy.The chemical bonding states were analyzed by x-ray photoelectron spectroscopy.The gas-sensing performance of WO_(3)/Ag_(3)PO_(4)sensors was systematically explored at room temperature.The composite sensors possessed a higher response and lower detection limit(1 ppm)to NH_(3)than those made of a single type of material;this is ascribed to the synergistic effect achieved by the heterojunction structure.Among the different composite sensors tested,gas sensor A5W5(Ag_(3)PO_(4):WO3mass ratio of 5:5)displayed the highest response to NH_(3)at room temperature.Interestingly,the A5W5 gas sensor exhibited relatively good stability and excellent selectivity to NH_(3).The A5W5 sensor also displayed a relatively good response under high humidity.The gas-sensing mechanism of the WO_(3)/Ag_(3)PO_(4)sensors is explained in detail.Taken together,the as-prepared sensor is highly efficient at detecting NH_(3)and could be suitable for practical applications.In addition,this study also provides a new method for developing Ag_(3)PO_(4)-based sensors in the gas-sensing field.展开更多
In order to avoid the formation ofηphase(W_(6)Co_(6)C or W_(3)Co_(3)C)that adversely affects the sintering process and its products in the preparation process of ultra-fine WC-Co powder,a technical route of prereduct...In order to avoid the formation ofηphase(W_(6)Co_(6)C or W_(3)Co_(3)C)that adversely affects the sintering process and its products in the preparation process of ultra-fine WC-Co powder,a technical route of prereduction of WO_(3)-Co_(3)O_(4)to WO_(2)-Co and then deep reduction carbonization to WC-Co powder has been proposed.This study mainly investigates the influence of gas partial pressure on the pre-reduction process of WO_(3)-Co_(3)O_(4)under a mixed atmosphere of H_(2)-C_(2)H_(4)-Ar at 600℃and establishes the kinetic equations of pre-reduction and carbon evolution.The results indicate that increasing the partial pressure of hydrogen is conducive to the rapid and complete conversion of WO_(3) to WO_(2).High carbon content can be generated by the deposition of C_(2)H_(4),and it hinders the diffusion of the reducing gas;WO_(3)still cannot be completely reduced to WO_(2)as the partial pressure of C_(2)H_(4) increases to 60%.For the carbon evolution of C_(2)H_(4),the carbon amount is positively related to the H_(2)partial pressure,but it shows the highest amount and evolution rate when the ethylene partial pressure is 20%.Based on the reduction rate curves of WO_(3) and carbon evolution rate curves of C_(2)H_(4),the rate equations of pre-reduction and carbon evolution of WO_(3)-Co_(3)O_(4)system at 600℃are established.The pre-reduction reaction belongs to the first-order reaction,and its equation is expressed as follows:r=-(dw_(WO_(3)))/dt=(9±0.15)×10^(-2)×P_(H_(2))^(0.44)P_(C_(2)H_(4))&(0.57)The carbon deposition rate equation of C_(2)H_(4) can be expressed as follows:r=-(dc_C)/dt=r_f-r_b≌7.35×10^(-2)×P_(C_(2)H_(4))^(0.31)展开更多
Heterojunction construction,especially S-scheme heterojunction,represents an efficient universal strategy to achieve high-performance photocatalytic materials.For further performance stimulation of these well-designed...Heterojunction construction,especially S-scheme heterojunction,represents an efficient universal strategy to achieve high-performance photocatalytic materials.For further performance stimulation of these well-designed heterojunctions,modulating the interfacial internal electric field(IEF)to steer dynamic charge transfer represents a promising approach.Herein,we realized the precise regulation of Fermi level(E_(F))of the oxidation semiconductor(mesoporous WO_(3-x))by tailoring the concentration of oxygen vacancies(V_(O)),maximizing the IEF intensity in Cs_(2)CuBr_(4)@WO_(3-x)(CCB@WO_(3-x))S-scheme heterojunction.The augmented IEF affords a robust driving force for directional electron delivery,leading to boosted charge separation.Hence,the developed CCB@WO_(3-x)S-scheme heterojunction demonstrated outstanding photocatalytic CO_(2)reduction performance,with the electron consumption rate(Relectron)up to 390.34μmol g^(-1)h^(-1),which is 3.28 folds higher than that of pure CCB.An in-depth analysis of the S-scheme electron transfer mode was presented via theoretical investigations,electron spin resonance(ESR),photo-irradiated Kelvin probe force microscopy(KPFM),and in-situ X-ray photoelectron spectroscopy(XPS).Finally,the CO_(2)photoconversion route was explored in detail using in-situ diffuse reflectance infrared Fourier transform spectroscopy(DRIFTS)and DFT theoretical calculations.展开更多
In-situ XRD,^(31)P NMR and ^(23)Na NMR were used to analyze the interaction behavior of Na_(3)V_(2)(PO_(4))_(3) at low voltage,and then a new intercalation model was proposed.During the transition from Na_(3)V_(2)(PO_...In-situ XRD,^(31)P NMR and ^(23)Na NMR were used to analyze the interaction behavior of Na_(3)V_(2)(PO_(4))_(3) at low voltage,and then a new intercalation model was proposed.During the transition from Na_(3)V_(2)(PO_(4))_(3) to Na_(4)V_(2)(PO_(4))_(3),Na ions insert into M1,M2 and M3 sites simultaneously.Afterwards,during the transition of Na_(4)V_(2)(PO_(4))_(3)to Na_(5)V_(2)(PO_(4))_(3),Na ions mainly insert into M3 site.展开更多
With the application of resins in various fields, numerous waste resins that are difficult to treat have been produced. The industrial wastewater containing Cr(Ⅵ) has severely polluted soil and groundwater environmen...With the application of resins in various fields, numerous waste resins that are difficult to treat have been produced. The industrial wastewater containing Cr(Ⅵ) has severely polluted soil and groundwater environments, thereby endangering human health. Therefore, in this paper, a novel functionalized mesoporous adsorbent PPR-Z was synthesized from waste amidoxime resin for adsorbing Cr(Ⅵ). The waste amidoxime resin was first modified with H3PO4 and ZnCl_(2), and subsequently, it was carbonized through slow thermal decomposition. The static adsorption of PPR-Z conforms to the pseudo-second-order kinetic model and Langmuir isotherm, indicating that the Cr(Ⅵ) adsorption by PPR-Z is mostly chemical adsorption and exhibits single-layer adsorption. The saturated adsorption capacity of the adsorbent for Cr(Ⅵ) could reach 255.86 mg/g. The adsorbent could effectively reduce Cr(Ⅵ) to Cr(Ⅲ) and decrease the toxicity of Cr(Ⅵ) during adsorption. PPR-Z exhibited Cr(Ⅵ) selectivity in electroplating wastewater. The main mechanisms involved in the Cr(Ⅵ) adsorption are the chemical reduction of Cr(Ⅵ) into Cr(Ⅲ) and electrostatic and coordination interactions. Preparation of PPR-Z not only solves the problem of waste resin treatment but also effectively controls Cr(Ⅵ) pollution and realizes the concept of “treating waste with waste”.展开更多
Photocatalytic H_(2) evolution from seawater splitting presents a promising approach to tackle the fossil energy crisis and mitigate carbon emission due to the abundant source of seawater and sunlight on the earth.How...Photocatalytic H_(2) evolution from seawater splitting presents a promising approach to tackle the fossil energy crisis and mitigate carbon emission due to the abundant source of seawater and sunlight on the earth.However,the development of efficient photocatalysts for seawater splitting remains a formidable challenge.Herein,a 2D/2D ZnIn_(2)S_(4)/WO_(3)(ZIS/WO_(3))heterojunction nanostructure is fabricated to efficiently separate the photoinduced carriers by steering electron transfer from the conduction band minimum of WO_(3) to the valence band maximum of ZIS via constructing internal electric field.Subsequently,plasmonic Au nanoparticles(NPs)as a novel photosensitizer and a reduction cocatalyst are anchored on ZIS/WO_(3) surface to further enhance the optical absorption of ZIS/WO_(3) heterojunction and accelerate the catalytic conversion.The obtained Au/ZIS/WO_(3) photocatalyst exhibits an outstanding H_(2) evolution rate of 2610.6 or 3566.3μmol g^(-1)h~(-1)from seawater splitting under visible or full-spectrum light irradiation,respectively.These rates represent an impressive increase of approximately 7.3-and 6,6-fold compared to those of ZIS under the illumination of the same light source.The unique 2D/2D structure,internal electric field,and plasmonic metal modification together boost the photocatalytic H_(2) evolution rate of Au/ZIS/WO_(3),making it even comparable to H_(2) evolution from pure water splitting.The present work sheds light on the development of efficient photocatalysts for seawater splitting.展开更多
基金financial support from the Collaborative Education Project of IndustryUniversity Cooperation of the Ministry of Education of China(Grant No.202101256024)the National Natural Science Foundation of China(Grant Nos.11904209 and 61802144)。
文摘A heterojunction structure design is a very good method for improving the properties of semiconductors in many research fields.This method is employed in the present study to promote the gas-sensing performance of Ag_(3)PO_(4)nanocomposites at room temperature(25℃).A nanocomposite of Ag_(3)PO_(4)nanoparticles and three-dimensional peony-like WO_(3)(WO_(3)/Ag_(3)PO_(4))was successfully prepared by the precipitation method.The crystalline phases were analyzed by xray diffraction and the microstructure was characterized by scanning electron microscopy and transmission electron microscopy.The chemical bonding states were analyzed by x-ray photoelectron spectroscopy.The gas-sensing performance of WO_(3)/Ag_(3)PO_(4)sensors was systematically explored at room temperature.The composite sensors possessed a higher response and lower detection limit(1 ppm)to NH_(3)than those made of a single type of material;this is ascribed to the synergistic effect achieved by the heterojunction structure.Among the different composite sensors tested,gas sensor A5W5(Ag_(3)PO_(4):WO3mass ratio of 5:5)displayed the highest response to NH_(3)at room temperature.Interestingly,the A5W5 gas sensor exhibited relatively good stability and excellent selectivity to NH_(3).The A5W5 sensor also displayed a relatively good response under high humidity.The gas-sensing mechanism of the WO_(3)/Ag_(3)PO_(4)sensors is explained in detail.Taken together,the as-prepared sensor is highly efficient at detecting NH_(3)and could be suitable for practical applications.In addition,this study also provides a new method for developing Ag_(3)PO_(4)-based sensors in the gas-sensing field.
基金the National Natural Science Foundation of China(22078326,21878305,21908227)。
文摘In order to avoid the formation ofηphase(W_(6)Co_(6)C or W_(3)Co_(3)C)that adversely affects the sintering process and its products in the preparation process of ultra-fine WC-Co powder,a technical route of prereduction of WO_(3)-Co_(3)O_(4)to WO_(2)-Co and then deep reduction carbonization to WC-Co powder has been proposed.This study mainly investigates the influence of gas partial pressure on the pre-reduction process of WO_(3)-Co_(3)O_(4)under a mixed atmosphere of H_(2)-C_(2)H_(4)-Ar at 600℃and establishes the kinetic equations of pre-reduction and carbon evolution.The results indicate that increasing the partial pressure of hydrogen is conducive to the rapid and complete conversion of WO_(3) to WO_(2).High carbon content can be generated by the deposition of C_(2)H_(4),and it hinders the diffusion of the reducing gas;WO_(3)still cannot be completely reduced to WO_(2)as the partial pressure of C_(2)H_(4) increases to 60%.For the carbon evolution of C_(2)H_(4),the carbon amount is positively related to the H_(2)partial pressure,but it shows the highest amount and evolution rate when the ethylene partial pressure is 20%.Based on the reduction rate curves of WO_(3) and carbon evolution rate curves of C_(2)H_(4),the rate equations of pre-reduction and carbon evolution of WO_(3)-Co_(3)O_(4)system at 600℃are established.The pre-reduction reaction belongs to the first-order reaction,and its equation is expressed as follows:r=-(dw_(WO_(3)))/dt=(9±0.15)×10^(-2)×P_(H_(2))^(0.44)P_(C_(2)H_(4))&(0.57)The carbon deposition rate equation of C_(2)H_(4) can be expressed as follows:r=-(dc_C)/dt=r_f-r_b≌7.35×10^(-2)×P_(C_(2)H_(4))^(0.31)
基金This work was financially supported by the National Natural Science Foundation of China(51972213)Natural Science Foundation of Shanghai(22ZR1460700).
文摘Heterojunction construction,especially S-scheme heterojunction,represents an efficient universal strategy to achieve high-performance photocatalytic materials.For further performance stimulation of these well-designed heterojunctions,modulating the interfacial internal electric field(IEF)to steer dynamic charge transfer represents a promising approach.Herein,we realized the precise regulation of Fermi level(E_(F))of the oxidation semiconductor(mesoporous WO_(3-x))by tailoring the concentration of oxygen vacancies(V_(O)),maximizing the IEF intensity in Cs_(2)CuBr_(4)@WO_(3-x)(CCB@WO_(3-x))S-scheme heterojunction.The augmented IEF affords a robust driving force for directional electron delivery,leading to boosted charge separation.Hence,the developed CCB@WO_(3-x)S-scheme heterojunction demonstrated outstanding photocatalytic CO_(2)reduction performance,with the electron consumption rate(Relectron)up to 390.34μmol g^(-1)h^(-1),which is 3.28 folds higher than that of pure CCB.An in-depth analysis of the S-scheme electron transfer mode was presented via theoretical investigations,electron spin resonance(ESR),photo-irradiated Kelvin probe force microscopy(KPFM),and in-situ X-ray photoelectron spectroscopy(XPS).Finally,the CO_(2)photoconversion route was explored in detail using in-situ diffuse reflectance infrared Fourier transform spectroscopy(DRIFTS)and DFT theoretical calculations.
基金supported by grants from the National Natural Science Foundation of China(No.22272055)multifunctional platform for innovation of ECNU(EPR).
文摘In-situ XRD,^(31)P NMR and ^(23)Na NMR were used to analyze the interaction behavior of Na_(3)V_(2)(PO_(4))_(3) at low voltage,and then a new intercalation model was proposed.During the transition from Na_(3)V_(2)(PO_(4))_(3) to Na_(4)V_(2)(PO_(4))_(3),Na ions insert into M1,M2 and M3 sites simultaneously.Afterwards,during the transition of Na_(4)V_(2)(PO_(4))_(3)to Na_(5)V_(2)(PO_(4))_(3),Na ions mainly insert into M3 site.
基金supported by the National Natural Science Foundation of China (No.52364022)the Natural Science Foundation of Guangxi Province,China (Nos.2023JJA160192 and 2021GXNSFAA220096)+1 种基金the Guangxi Science and Technology Major Project,China (No.AA23073018)the Guangxi Chongzuo Science and Technology Plan,China (No.2023ZY00503).
文摘With the application of resins in various fields, numerous waste resins that are difficult to treat have been produced. The industrial wastewater containing Cr(Ⅵ) has severely polluted soil and groundwater environments, thereby endangering human health. Therefore, in this paper, a novel functionalized mesoporous adsorbent PPR-Z was synthesized from waste amidoxime resin for adsorbing Cr(Ⅵ). The waste amidoxime resin was first modified with H3PO4 and ZnCl_(2), and subsequently, it was carbonized through slow thermal decomposition. The static adsorption of PPR-Z conforms to the pseudo-second-order kinetic model and Langmuir isotherm, indicating that the Cr(Ⅵ) adsorption by PPR-Z is mostly chemical adsorption and exhibits single-layer adsorption. The saturated adsorption capacity of the adsorbent for Cr(Ⅵ) could reach 255.86 mg/g. The adsorbent could effectively reduce Cr(Ⅵ) to Cr(Ⅲ) and decrease the toxicity of Cr(Ⅵ) during adsorption. PPR-Z exhibited Cr(Ⅵ) selectivity in electroplating wastewater. The main mechanisms involved in the Cr(Ⅵ) adsorption are the chemical reduction of Cr(Ⅵ) into Cr(Ⅲ) and electrostatic and coordination interactions. Preparation of PPR-Z not only solves the problem of waste resin treatment but also effectively controls Cr(Ⅵ) pollution and realizes the concept of “treating waste with waste”.
基金supported by the National Natural Science Foundation of China(21872104,21501131,21978216 and 22272082)the Natural Science Foundation of Tianjin for Distinguished Young Scholar(20JCJQJC00150)the Analytical&Testing Center of Tiangong University for PL work。
文摘Photocatalytic H_(2) evolution from seawater splitting presents a promising approach to tackle the fossil energy crisis and mitigate carbon emission due to the abundant source of seawater and sunlight on the earth.However,the development of efficient photocatalysts for seawater splitting remains a formidable challenge.Herein,a 2D/2D ZnIn_(2)S_(4)/WO_(3)(ZIS/WO_(3))heterojunction nanostructure is fabricated to efficiently separate the photoinduced carriers by steering electron transfer from the conduction band minimum of WO_(3) to the valence band maximum of ZIS via constructing internal electric field.Subsequently,plasmonic Au nanoparticles(NPs)as a novel photosensitizer and a reduction cocatalyst are anchored on ZIS/WO_(3) surface to further enhance the optical absorption of ZIS/WO_(3) heterojunction and accelerate the catalytic conversion.The obtained Au/ZIS/WO_(3) photocatalyst exhibits an outstanding H_(2) evolution rate of 2610.6 or 3566.3μmol g^(-1)h~(-1)from seawater splitting under visible or full-spectrum light irradiation,respectively.These rates represent an impressive increase of approximately 7.3-and 6,6-fold compared to those of ZIS under the illumination of the same light source.The unique 2D/2D structure,internal electric field,and plasmonic metal modification together boost the photocatalytic H_(2) evolution rate of Au/ZIS/WO_(3),making it even comparable to H_(2) evolution from pure water splitting.The present work sheds light on the development of efficient photocatalysts for seawater splitting.
